EN 3283-1994 en Bearings Airframe Rolling - Rigid Single Row Ball Bearings in Corrosion Resisting Steel - Diameter Series 8 and 9 - Dimensions and Loads《飞机机架滚动轴承 耐腐蚀钢制硬性单排滚珠轴承 直径系列.pdf

《EN 3283-1994 en Bearings Airframe Rolling - Rigid Single Row Ball Bearings in Corrosion Resisting Steel - Diameter Series 8 and 9 - Dimensions and Loads《飞机机架滚动轴承 耐腐蚀钢制硬性单排滚珠轴承 直径系列.pdf》由会员分享，可在线阅读，更多相关《EN 3283-1994 en Bearings Airframe Rolling - Rigid Single Row Ball Bearings in Corrosion Resisting Steel - Diameter Series 8 and 9 - Dimensions and Loads《飞机机架滚动轴承 耐腐蚀钢制硬性单排滚珠轴承 直径系列.pdf（11页珍藏版）》请在麦多课文档分享上搜索。

1、4 CEN EN+3283 94 3404589 007L2L4 7LT = BRITISH STANDARD AEROSPACE SERIES Bearings, airframe rolling - Rigid single row ball bearings in corrosion resisting steel - Diameter series 8 and 9 - Dimensions and loads The European Standard EN 3283 : 1994 has the status of a British Standard UDC 629 32 : 62

2、1.822.74.004.1 : 9.14.018.89 BS EN 3283 : 1994 CEN EN*32i3 94 E 3404589 0071215 b5b = BS EN 3283 : 1994 This British Standard, having been prepared under the direction of the Aerospace Standards Policy Committee, was published under the authority of the Standards Board and comes into effect on 15 Se

3、ptember 1994 O BSI 1994 Cooperating organizations The European Committee for Standardization (CEN), under whose supervision this European Standard was prepared, comprises the national standards organizations of the following countries: Austria Belgium Denmark Finland France Germany Greece Iceland Ir

4、eland Italy Luxembourg Netherlands Norway Portugal Spain Sweden Switzerland United Kingdom Oesterreichisches Normungsinstitut Institut belge de normalisation Dansk Standard Suomen Standardisoimisliito, r. y. Association francaise de normalisation Deutsches Institut fr Normung e.V. Hellenic Organizat

5、ion for Standardization Technological Institute of Iceland National Standards Authority of Ireland Ente Nazionale Italiano di Unificazione Inspection du Travail et des Mines Nederlands Normalisatie-instituut Norges Standardiseringsforbund Instituto Portugus da Qualidade Asociacin Espaola de Normaliz

6、acin y Certificacin Standardiseringskommissionen i Sverige Association suisse de normalisation British Standards Institution Amendments issued since publication Amd. No. 1 Date I Text affected The following BSI references relate to the work on this standard: Committee reference MCEI7 Draft for comme

7、nt 88/72196 DC ISBN O 580 21883 X CEN ENx3283 94 = 3404589 0073236 592 = BS EN 3283 : 1994 Contents Cooperating organizations National foreword Page Inside front page i Foreword 2 Specification 1 Scope 3 2 Normative references 3 3 Definition 3 4 Symbols 3 5 Required characteristics 4 6 Designation 6

8、 7 Marking 6 8 Echnical specification 6 National annexes NA (informative) Committees responsible Inside back page NB (informative) Cross-references Inside back page National foreword This British Standard has been prepared under the direction of the Aerospace Standards Policy Committee and is the En

9、glish language version of EN 3283 : 1994 Aerospace series - Bearings, ai?frame rolling - Rigid single row ball bearings in corrosion redsting steel - Diameter seres 8 and 9 - mensi ions and loads, published by the European Committee for Standardization (CEN). EN 3283 was produced as a result of inte

10、rnational discussions in which the United Kingdom took an active part. Compliance with a British Standard does not of itself confer immunity from legal obligations. i CEN EN*3283 94 3404589 0073237 429 EUROPEAN STANDARD EN 3283 NORME EUROPENNE EUROPISCHE NORM June 1994 UDC 629.7.02 : 621.822.74.004.

11、1 : 669.14.018.89 Descriptors: Aircraft industry, airframe bearings, ball bearings, corrosion resisting steel, dimensions, static loads English version Aerospace series - Bearings, airframe rolling - Rigid single row ball bearings in corrosion resisting steel - Diameter series 8 and 9 - Dimensions a

12、nd loads Srie arospatiale - Roulements pour structures daronefs - Roulements en acier rsistant la corrosion rigides, une range de billes - Srie de diamtres 8 et 9 - Dimensions et charges Belastungen Luft- und Raumfahrt - Flugwerklager - Einreihige Rillenkugellager aus korrosionsbestndigem Stahl - Du

13、rchmesserreihen 8 und 9 - Mafie und This European Standard was approved by CEN on 1994-06-07. CEN members are bound to comply with the CENICENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-dat

14、e lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the

15、responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, N

16、orway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels O 1994 Copyright reserved to CEN members Ref. No. EN 3283 : 1994 E Previou

17、s page is blank CEN EN*3283 74 = 3404587 007L218 365 Page 2 EN 3283 : 1994 Foreword This European Standard has been prepared by the European Association of Aerospace Manufacturers (AECMA). After inquiries and votes carried out in accordance with the rules of this Association, this standard has succe

18、ssively received the approval of the National Associations and the Official Services of the member countries of AECMA, prior to its presentation to CEN. This standard was submitted for formal vote, and the result was positive. This European Standard shall be given the status of a national standard,

19、either by publication of an identical text or by endorsement, at the latest by December 1994, and conflicting national standards shail be withdrawn at the latest by December 1994. According to the CENKENELEC Internal Regulations, the following countries are bound to implement this European Standard:

20、 Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, United Kingdom. CEN EN*3283 94 m 3404589 007L2L9 2TL m Page 3 EN 3283 : 1994 1 Scope This standard specifies the characteristics of rigid sing

21、le row ball bearings in corrosion resisting steel of diameter series 8 and 9 1) designed to withstand only slow rotations and oscillations under load. They are intended for use between fixed and moving parts of the aircraft structure and their control mechanisms. The airframe rolling bearings define

22、d in this standard are used from - 54 OC to + 150 OC. However, being lubricated with the following greases : - very high pressure grease, ester type (code A), operational range - 73 OC to + 121 OC or - very high pressure grease, synthetic hydrocarbons, general purpose (code BI, operational range - 5

23、4 OC to + 177 OC (see EN 3280). their field of application when lubricated with code A grease is limited to + 121 OC. 2 Normative references This European Standard incorporates by dated or undated reference provisions from other publications. These normative references are cited at the appropriate p

24、laces in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication re

25、ferred to applies. IS0 15 IS0 1 132 EN 2030 EN 2226 EN 3280 Rolling bearings - Radial bearings - Boundary dimensions - General plan Rolling bearings - Tolerances - Definitions Steel FE-PM43 - Hardened and tempered - Bars D 5 150 mm - Aerospace series 2) Steel FE-PM43 - Hardened and tempered - Hand a

26、nd die forgings De 5 150 mm - Aerospace series 2) Aerospace series - Bearings, airframe rolling, rigid or self-aligning - Technical specification 3 Definition For the purposes of this standard, the following definition applies : Bearing : full complement of balls (without cage), with filling slot. 4

27、 Symbols The definitions of tolerances and clearances are given in IS0 1 132. single plane mean bore diameter deviation single plane mean outside diameter deviation axial internal clearance radial internal clearance assembled bearing inner ring face runout with raceway assembled bearing outer ring f

28、ace runout with raceway radial runout of assembled bearing inner ring radial runout of assembled bearing outer ring permissible static axial load permissible static radial load. I 1) See IS0 15 2) Published as AECMA Standard at the date of publication of this standard CEN EN*3283 94 3404589 0073220

29、TL3 W Page 4 EN 3283: 1994 5 Required characteristics 5.1 Configuration : see figure 1 ; the bearings are fitted with either seals or shields. Values : see table 1. Dimensions - Tolerances - Clearances - Loads - Mass 5.2 Surface roughness Raceways and rolling elements : Ra = 0,2 pm Bore, side faces

30、and cylindrical outer surface : Ra = 0,8 pm. 5.3 Materials Inner ring : EN 2030 or EN 2226, 2 58 HRC Outer ring : EN 2030 or EN 2226,2 58 HRC Balls : EN 2030, 2 58 HRC Shields : Corrosion resisting material Seals : Polytetrafluoroethylene (PTFE) or polytetrafluoroethylene (PTFE) reinforced with fibr

31、eglass. Type with shields Code P Type with seals Code E NOTE 1 : The installation of seals and shields is at the manufacturers option. NOTE 2 : The shields shall not extend beyond B . Figure 1 30 35 40 50. 60 O -11 -10 7 30 42 33.1 35 47 38.3 40 52 43,3 50 65 53 O -13 60 10 78 63.5 O -12 O -15 I I s

32、e, 40 Ki, L 6.5 40 8.5 14 18 22 32 55 16 18 20 23 29 47 77 CEN EN*3283 94 D 3404589 007L22L 95T D Page 5 EN 3283 : 1994 e Table 1 Dimensions in millimetres kgll O00 d Tolerances w - 10 10 22 13 12 12 24 15 15 15 28 17,6 17 17 30 19,6 6 O -8 O -9 16 I I i8 I I 2o I 2o I I 32 I 23 I 20 I I 23 I 0.3 to

33、 0.8 1-44 I O0 I - d Code internal clearances Pm - Runout tolerances max. prn I Permissible static loads 2) kN Axial Radial ! Fa max. Starting torque 1 1 in mN.m Axial max. Ga Radial- I Axial I Radi Code 1- Code 10 12 - 4,s 1 10.6 2 to 13 3 to 18 5 to 20 15 17 16 115 17.6 17.3 9.8 21.5 11.1 24.5 20

34、25 30 35 40 50 - - - - - 1 O0 40 25 31,8 6 to 20 120 60 - 150 1) Definition, see EN 3280. 2) Axial and radial loads may be applied simultaneously. For ultimate static loads, see EN 3280. CEN EN*3283 94 3404589 0073222 896 Page 6 EN 3283 : 1994 6 Designation EXAMPLE : Description block Identity block

35、 BEARING I EN3283AlOP I - Code Number for of grease this standard type (see 1 ) Diameter code d (see table 1) Code for type (see figure 1) NOTE : If necessary, the code 19005 shall be placed between the description block and the identity block. 7 Marking In addition to the manufacturers own marking,

36、 each bearing shall be marked, on one side face only, using the identity block, see 6. Marking position and method are at the manufacturers option. 8 Technical specification See EN 3280. CEN EN*3283 94 W 3404589 0073223 722 W BS EN 3283 : 1994 National annex NA (informative) Committees responsible T

37、he United Kingdom participation in the preparation of this European Standard was entrusted by the Aerospace Standards Policy Committee (ACE/-) to Rchnical Committee MCEI7 upon which the following bodies were represented: Ball and Roller Bearing Manufacturers Association Ministry of Defence Society o

38、f British Aerospace Companies Ltd. National annex NB (informative) Cross-references The British Standards corresponding to the international standards referred to in the text are as follows. international standard Corresponding British Standard IS0 15 : 1981 IS0 1132 : 1980 BS 6267 : 1982 Specificat

39、ion for rolling bearings: boundary dimensions for radial bearings BS 6107 Rolling bearings : tolerances Part 1 : 1981 Glossary of terms CEN EN83283 94 3404589 0073224 669 = BS EN 3283 : 1994 BSI 2 Park Street London W1A 2BS BSI Linford Wood Milton Keynes MK14 6LE 9409 - 4 - 0.4k - FP BSI - British S

40、tandards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Contract requirements A British Standard does not purport to include all the nece

41、ssary provisions of a contract. Users of British Standards are responsible for their correct application. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. Any person who finds an inaccur

42、acy or ambiguity while using this British Standard should notify BSI without delay so that the matter may be investigated swiftly. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Ord

43、ers for all BSI, international and foreign standards publications should be addressed to Customer Services, Publications at Milton Keynes: Tel: 0908 221166; Fax: 0908 322484. In response to orders for international and European standards, it is BSI policy to supply the BSI implementation of those th

44、at have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library, the Standardline Database, the BSI Information Technology Service (BITS) and its Technical

45、 Help to Exporters Service. Contact Customer Services, Information at Milton Keynes: El: 0908 226888. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Head

46、of Customer Services, Membership Group at Milton Keynes: %l: O908 226777. Copyright Copyright subsists in all BSI publications and no part may be reproduced in any form without the prior permission in writing of BSI. This does not preclude the free use, in the course of implementing the standard of

47、necessary details such as symbols and size, type or grade designations including use by incorporation into computer programs, but where these details are reproduced including without limitation in printed form, in computer programs or in any other form whatsoever, the permission in writing of BSI must be obtained and if granted will be on terms including royalty, before the product is sold, licensed or otherwise exploited for commercial gain. Enquiries about copyright should be made to the Copyright Manager, Publications at Milton Keynes. ISBN O 580 21883 X MCE/7