EN 2003-010-2007 en Aerospace series - Titanium and titanium alloys - Test methods - Part 010 Sampling for determination of hydrogen content《航空航天系列 钛和钛合金的试验方法 第010部分 氢含量测定用取样》.pdf

《EN 2003-010-2007 en Aerospace series - Titanium and titanium alloys - Test methods - Part 010 Sampling for determination of hydrogen content《航空航天系列 钛和钛合金的试验方法 第010部分 氢含量测定用取样》.pdf》由会员分享，可在线阅读，更多相关《EN 2003-010-2007 en Aerospace series - Titanium and titanium alloys - Test methods - Part 010 Sampling for determination of hydrogen content《航空航天系列 钛和钛合金的试验方法 第010部分 氢含量测定用取样》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 2003-010:2007Aerospace series Titanium and titanium alloys Test methods Part 010: Sampling for determination of hydrogen contentThe European Standard EN 2003-010:2007 has the status of a British StandardICS 49.025.30g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g4

2、4g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 2003-010:2007This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 April 2007 BSI 2007ISBN 978 0 580

3、50531 7National forewordThis British Standard was published by BSI. It is the UK implementation of EN 2003-010:2007.The UK participation in its preparation was entrusted by Technical Committee ACE/61, Metallic materials for aerospace purposes, to Panel ACE/61/-/49, Titanium and its alloys.A list of

4、organizations represented on ACE/61/-/49 can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligat

5、ions. Amendments issued since publicationAmd. No. Date CommentsEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 2003-010March 2007ICS 49.025.30English VersionAerospace series - Titanium and titanium alloys - Test methods -Part 010: Sampling for determination of hydrogen contentSrie arospatiale - Ti

6、tane et alliages de titane - Mthodesdessais - Partie 010 : chantillonnage pour ladtermination de la teneur en hydrogneLuft- und Raumfahrt - Titan und Titanlegierungen -Prfverfahren - Teil 010: Probenentnahme fr dieBestimmung des WasserstoffgehaltesThis European Standard was approved by CEN on 5 Octo

7、ber 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtain

8、ed on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management

9、 Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Pol

10、and, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2007 CEN All rights of exploitation in any form and by any

11、 means reservedworldwide for CEN national Members.Ref. No. EN 2003-010:2007: E2 Contents Page Foreword3 Introduction .4 1 Scope 4 2 Normative references 4 3 General requirements4 4 Location of test pieces4 5 Analysis samples.6 EN 2003-010:20073 Foreword This document (EN 2003-010:2007) has been prep

12、ared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countr

13、ies of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2007, and conflicting national standards shall be withdrawn at the latest by September 2007.

14、 Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizatio

15、ns of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,

16、 Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. EN 2003-010:20074 Introduction This standard is part of the series of EN metallic material standards for aerospace applications. The general organization of this series is described in EN 4258. 1 Scope This standard specifies th

17、e location of the test pieces and the analysis samples used for the determination of hydrogen content in titanium and titanium alloys products. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cit

18、ed applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 4258, Aerospace series Metallic materials General organization of standardization Links between types of EN standards and their use. 3 General requirements 3.1 The hydrogen conten

19、t of a product shall be determined in the delivery condition unless otherwise agreed between manufacturer and purchaser. 3.2 The test pieces shall be cut so as to avoid contamination. Clean cutting tools shall be used. Abrasive wheel cutting and cutting fluids are permissible provided they are appli

20、ed under controlled conditions. 3.3 Cutting of the hydrogen analysis sample by laboratory personnel shall be done as far as possible using clean dry cutting tools. At this stage, abrasive cutting and cutting fluids are to be avoided unless it can be demonstrated that the technique used does not sign

21、ificantly affect the analysis results. 4 Location of test pieces 4.1 General Since hydrogen is more highly concentrated in zones close to the surface, the location of the test piece shall ensure that an analysis sample representative of the product is taken at a defined location related to the produ

22、ct surface; or if that surface remains in the finished part it shall include the product surface. EN 2003-010:20075 4.2 Sheet and strip (thickness 6 mm) Test pieces shall be taken so as to include the total sheet or strip thickness, in accordance with Figure 1. Figure 1 Sheet and strip (thickness 6

23、mm) 4.3 Plate (thickness 6 mm) Depending on the thickness of the plate the test pieces shall either: contain at least one product surface as shown in Figure 2; or include the total thickness of the plate. Figure 2 Plate (thickness 6 mm), forgings and castings 4.4 Bar for machining, bar for fasteners

24、, sections and wire 4.4.1 For products with a diameter or thickness 5 mm, the test pieces shall include the total thickness of the product. EN 2003-010:20076 4.4.2 For products with a diameter or thickness 5 mm, the test piece shall either: contain at least one product surface as shown in Figure 3;

25、or include the total thickness of the product. Figure 3 Forging stock (diameter or thickness 100 mm), bar for machining, bar for fasteners, sections and wire 4.5 Forging stock For forging stock with a diameter or thickness 100 mm, the test pieces location shall be in accordance with Figure 3. For la

26、rger diameters or thicknesses, the test pieces location shall be agreed between manufacturer and purchaser. 4.6 Forgings and castings Unless otherwise required in the inspection schedule, the location of test pieces shall be in accordance with Figure 2. 4.7 Tubes For tubes with a wall thickness 5 mm

27、, the test pieces shall include the whole wall thickness. For larger wall thicknesses, the location of the test pieces shall be agreed between manufacturer and purchaser. 5 Analysis samples 5.1 Mass The analysis samples shall be taken from the test pieces. They shall have normally a mass of less tha

28、n 1 g. 5.2 Cleaning The analysis samples shall be cleaned, degreased and dried. Immediately before analysis is carried out, the laboratory personnel shall ensure that the analysis sample has a clean metallic, surface. EN 2003-010:2007blankBS EN 2003-010:2007BSI389 Chiswick High RoadLondonW4 4ALBSI B

29、ritish Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of B

30、ritish Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of t

31、he technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buy

32、ing standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for internation

33、al standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical

34、Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with stand

35、ards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via Br

36、itish Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permi

37、tted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.This does not preclude the free use, in the course o

38、f implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.