EN 2003-009-2007 en Aerospace series - Test methods - Titanium and titanium alloys - Part 009 Determination of surface contamination《航空航天系列的试验方法 钛和钛合金 第009部分 表面污染测定》.pdf

《EN 2003-009-2007 en Aerospace series - Test methods - Titanium and titanium alloys - Part 009 Determination of surface contamination《航空航天系列的试验方法 钛和钛合金 第009部分 表面污染测定》.pdf》由会员分享，可在线阅读，更多相关《EN 2003-009-2007 en Aerospace series - Test methods - Titanium and titanium alloys - Part 009 Determination of surface contamination《航空航天系列的试验方法 钛和钛合金 第009部分 表面污染测定》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 2003-009:2007Aerospace series Test methods Titanium and titanium alloys Part 009: Determination of surface contaminationThe European Standard EN 2003-009:2007 has the status of a British StandardICS 49.025.30g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g4

2、0g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 2003-009:2007This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 April 2007 BSI 2007ISBN 978 0 580 50530 0N

3、ational forewordThis British Standard was published by BSI. It is the UK implementation of EN 2003-009:2007.The UK participation in its preparation was entrusted by Technical Committee ACE/61, Metallic materials for aerospace purposes, to Panel ACE/61/-/49, Titanium and its alloys.A list of organiza

4、tions represented on ACE/61/-/49 can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations. Am

5、endments issued since publicationAmd. No. Date CommentsEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 2003-009March 2007ICS 49.025.30English VersionAerospace series - Test methods - Titanium and titanium alloys -Part 009: Determination of surface contaminationSrie arospatiale - Mthodes dessais -

6、Titane et alliagesde titane - Partie 009 : Dtermination de la contaminationde surfaceLuft- und Raumfahrt - Prfverfahren - Titan undTitanlegierungen - Teil 009: Bestimmung derOberflchenverunreinigungThis European Standard was approved by CEN on 5 October 2006.CEN members are bound to comply with the

7、CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or

8、to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial version

9、s.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain,

10、Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2007 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.

11、Ref. No. EN 2003-009:2007: E2 Contents Page Foreword3 Introduction .4 1 Scope 4 2 Normative references 4 3 Terms and definitions .4 4 Principle4 5 Micrographic examination (Method A) 5 6 Hardness testing (Method B)5 7 Test report 6 Annex A (informative) Examples of contamination .7 EN 2003-009:20073

12、 Foreword This document (EN 2003-009:2007) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Ass

13、ociations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2007, and conflicting national stand

14、ards shall be withdrawn at the latest by September 2007. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC

15、Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg

16、, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. EN 2003-009:20074 Introduction Contamination caused by an -stabilizer occurs in an environment containing oxygen, nitrogen or carbon when the product surface reaches a temp

17、erature which allows these elements to diffuse into the product surface. It leads to the formation of an -stabilized surface which is hard and brittle, seldom exceeding 0,2 mm and is detrimental to the product. 1 Scope This standard specifies two methods of determining surface contamination caused b

18、y an -stabilizer on titanium and titanium alloys, for aerospace applications. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the refe

19、renced document (including any amendments) applies. EN 2002-7, Aerospace series Metallic materials Test methods Part 7: Hardness test. 1)EN 3114-001, Aerospace series Test method Microstructure of ( + ) titanium alloy wrought products Part 001: General requirements. 3 Terms and definitions For the p

20、urposes of this document, the terms and definitions given in EN 3114-001 apply. 4 Principle Determination of surface contamination is carried out by: micrographic examination (Method A); or hardness testing (Method B). 1) Published as ASD Prestandard at the date of publication of this standard. EN 2

21、003-009:20075 5 Micrographic examination (Method A) 5.1 Sampling Unless otherwise specified the product shall be sampled in the delivery condition, such that the product surface can be examined at its transverse section. The location of the sample shall be at the discretion of the manufacturer, unle

22、ss otherwise specified. The sampling procedure shall not result in any heating which may lead to a contamination of the test sample. 5.2 Procedure 5.2.1 Preparation of the micro-section The micro-section selected from the test sample shall be prepared by mechanical polishing. The method of preparati

23、on shall not cause any damage to the microstructure. It shall lead to sharp edges. The micro-section shall be etched, using an appropriate solution e.g.: 2 % to 5 % HF (hydrofluoric acid); 40 % to 50 % 2-Propanol (isopropylalcohol); water. or 2 % to 5 % HF (hydrofluoric acid); 10 % to 20 % HNO3(nitr

24、ic acid); water. 5.2.2 Micro-examination Optical micro-examination shall be carried out with a magnification of 100 times to 500 times. 5.3 Expression of results Report any appearance of a white layer or an area with a high density of light colour -phase (see annex), indicating the presence of surfa

25、ce contamination. 6 Hardness testing (Method B) 6.1 Sampling See 5.1. EN 2003-009:20076 6.2 Procedure 6.2.1 Preparation of the specimen The section to be inspected shall be prepared by mechanical polishing. This preparation shall not cause any alteration. It shall lead to sharp edges. 6.2.2 Tests Un

26、less otherwise specified, Vickers hardness measurements shall be carried out under a load of 0,200 kg according to EN 2002-7 at the following locations: at least, three points at a distance 0,1 mm from the section surface; at least, three points at about mid-thickness of the section. The average val

27、ue of these measurements shall be calculated for each location. 6.3 Expression of results Report the difference between the two average values. A difference between these values 50 HV0,2, indicates surface contamination. 7 Test report The test report shall refer to this standard and shall include: c

28、omplete identification of the tested product, including the manufacturers name, designation and batch number; method used : micrographic examination (Method A) or hardness testing (Method B); location of test sample; method of test sample preparation; all relevant test sample dimensions; date of tes

29、t and traceability to individuals performing the test work; equipment used; for micrographic examination (Method A) the etchant used; for hardness test (Method B), recorded individual and average hardnesses for the two test locations and the difference between the two averages; test results; any fac

30、tor which may have affected the results and any deviation from the test method. EN 2003-009:20077 Annex A (informative) Examples of contamination EXAMPLE 1 (X 400) EXAMPLE 2 (X 250) EN 2003-009:2007BS EN 2003-009:2007BSI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the in

31、dependent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that th

32、ey possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the i

33、dentity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, internat

34、ional and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply

35、the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI el

36、ectronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial

37、 discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at ht

38、tp:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Pat

39、ents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary

40、 details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.