EN 13766-2010 en Thermoplastic multi-layer (non-vulcanized) hoses and hose assemblies for the transfer of liquid petroleum gas and liquefied natural gas - Specification《液化石油气和液化天然气.pdf

《EN 13766-2010 en Thermoplastic multi-layer (non-vulcanized) hoses and hose assemblies for the transfer of liquid petroleum gas and liquefied natural gas - Specification《液化石油气和液化天然气.pdf》由会员分享，可在线阅读，更多相关《EN 13766-2010 en Thermoplastic multi-layer (non-vulcanized) hoses and hose assemblies for the transfer of liquid petroleum gas and liquefied natural gas - Specification《液化石油气和液化天然气.pdf（24页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN 13766:2010ICS 23.040.70NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDThermoplastic multi-layer (non-vulcanized)hoses and hoseassemblies for thetransfer of liquidpetroleum gas andliquefied natural gas SpecificationThis British Standardwas published under

2、theauthority of the StandardsPolicy and StrategyCommittee on 30 June2010 BSI 2010ISBN 978 0 580 64332 3Amendments/corrigenda issued since publicationDate CommentsBS EN 13766:2010National forewordThis British Standard is the UK implementation of EN 13766:2010. Itsupersedes BS EN 13766:2003 which is w

3、ithdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee PRI/66, Rubber and plastics tubing, hoses and hoseassemblies.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the nece

4、ssary provisionsof a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunityfrom legal obligations.BS EN 13766:2010EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13766 June 2010 ICS 23.040.70 Supersedes EN 13766:2003English Version

5、Thermoplastic multi-layer (non-vulcanized) hoses and hose assemblies for the transfer of liquid petroleum gas and liquefied natural gas - Specification Tuyaux et flexibles en thermoplastique multi couches (non vulcaniss) utiliss pour le dpotage de gaz ptrolier liquide et gaz naturel liqufi - Spcific

6、ation Thermoplastische, mehrlagige (nicht vulkanisierte) Schluche und Schlauchleitungen fr die Frderung von Flssiggas und verflssigtem Erdgas - Spezifikation This European Standard was approved by CEN on 5 May 2010. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stip

7、ulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard

8、 exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standa

9、rds bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and Un

10、ited Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13766:2010

11、: EBS EN 13766:2010EN 13766:2010 (E) 2 Contents Page Foreword 31 Scope 42 Normative references 43 Terms and definitions . 54 Classification 55 Materials and construction . 56 Dimensions . 66.1 Internal diameters, with tolerances and minimum bend radii . 66.2 Tolerance on length . 77 Performance requ

12、irements of hoses and hose assemblies 77.1 Film and fabric . 77.2 Hoses 77.3 End fittings . 87.4 Hose assemblies 87.5 Electrical continuity . 98 Test frequency . 99 Type tests . 910 Marking . 1010.1 Hose marking . 1010.2 Hose assembly marking 10Annex A (normative) Crush recovery test 11Annex B (norm

13、ative) Method of test for thermal ageing . 13Annex C (normative) Method of test of fittings subjected to low temperatures. 14C.1 General 14C.2 Specimen size 14Annex D (normative) Sequence of hydrostatic tests . 15Annex E (normative) Method of test for fitting security 16Annex F (normative) Method of

14、 test for leak tightness . 18Annex G (normative) Type and routine tests for hoses and hose assemblies 19Annex H (informative) Batch tests for hoses and hose assemblies 20Bibliography 21BS EN 13766:2010EN 13766:2010 (E) 3 Foreword This document (EN 13766:2010) has been prepared by Technical Committee

15、 CEN/TC 218 “Rubber and plastics hoses and hose assemblies”, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2010, and conflicting national standa

16、rds shall be withdrawn at the latest by December 2010. This document supersedes EN 13766:2003. Compared to the 2003 version, changes have been made to the following (sub)clauses, tables and annexes: Scope: Reference to EN 1474-2 added; Table 1: Temperature has been changed to 196 C; 7.1: Reference t

17、o new test standards added; Table 3: Change in length test refined; Table 4: Electrical resistance test refined; 7.5: Electrical Continuity text added; 10.1: Hose marking simplified; Annex E: text revised to incorporate cyclic testing to low temperatures; Annex G: Tests moved from hose to hose assem

18、blies; Annex H: Tests moved from hose to hose assemblies. This document has also been presented to ISO/TC 45/SC 1, for adoption as an ISO standard under the Vienna agreement. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound

19、to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Swe

20、den, Switzerland and United Kingdom. BS EN 13766:2010EN 13766:2010 (E) 4 1 Scope This European Standard specifies requirements for two types of thermoplastic multi-layer (non-vulcanized) transfer hoses and hose assemblies for carrying liquefied petroleum gas and liquefied natural gas. Each type is s

21、ubdivided into two classes, one for onshore duties, and the other for offshore. This European Standard is applicable for hose sizes from 25 mm to 250 mm, working pressures from 10,5 bar to 25 bar and operating temperatures from 196 C to + 45 C. NOTE Offshore LNG hose assemblies are also specified in

22、 EN 1474-2. WARNING Persons using this European Standard should be familiar with normal laboratory practice. This standard does not purport to address all the safety problems, if any, associated with its use. It is the responsibility of the user to establish appropriate health and safety practices a

23、nd to ensure compliance with any national regulatory conditions. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced docume

24、nt (including any amendments) applies. EN 10045-1, Metallic materials Charpy impact test Part 1: Test method EN 10088-3, Stainless steels Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purpose

25、s EN ISO 527-1, Plastics - Determination of tensile properties Part 1: General principles (ISO 527-1:1993 including Corr 1:1994) EN ISO 1043-1, Plastics Symbols and abbreviated terms Part 1: Basic polymers and their special characteristics (ISO 1043-1:2001) EN ISO 1402:2009, Rubber and plastics hose

26、s and hose assemblies Hydrostatic testing (ISO 1402:2009) EN ISO 1746, Rubber or plastics hoses and tubing Bending tests (ISO 1746:1998, including technical corrigendum 1:1999) EN ISO 4671, Rubber and plastics hose and hose assemblies Methods of measurement of the dimensions of hoses and the lengths

27、 of hose assemblies (ISO 4671:2007) EN ISO 4672, Rubber and plastics hoses Sub-ambient temperature flexibility tests (ISO 4672:1997) EN ISO 7326, Rubber and plastics hoses Assessment of ozone resistance under static conditions (ISO 7326:2006) EN ISO 8031:2009, Rubber and plastics hoses and hose asse

28、mblies Determination of electrical resistance and conductivity (ISO 8031:2009) EN ISO 8330:2008, Rubber and plastics hoses and hose assemblies Vocabulary (ISO 8330:2007) EN ISO 13934-1, Textiles Tensile properties of fabrics Part 1: Determination of maximum force and elongation at maximum force usin

29、g the strip method (ISO 13934-1:1999) BS EN 13766:2010EN 13766:2010 (E) 5 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN ISO 8330:2008 apply. 4 Classification Hoses shall be classified according to their usage, working pressure and working temperatur

30、e range as given in Table 1. Table 1 Pressure and temperature range Pressure/temperature Class Aa Class Bb Class AClass B Type 1 Type 1 Type 2 Type 2 Maximum working pressure (bar) 25 20 13 10,5 Proof pressure (bar) 37,5 30 19,5 15,8 Minimum burst pressure (bar) 100 100 52 52,5 Working temperature r

31、ange (C) 50 3 to + 45 50 3 to + 45 196 5 to + 45 196 5 to + 45 NOTE 1 1 bar = 0,1 Mpa NOTE 2 Due to pressurisation during test and operations the temperature of the fluid could increase. The indicated temperatures are measured at atmospheric pressure; aClass A is for use onshore. bClass B is for use

32、 offshore. 5 Materials and construction Hoses shall be constructed as shown in Figure 1 and shall consist of the following: a) Class A: 1) An internal wire helix of stainless steel conforming to EN 10088-3, numbers 1.4306, 1.4401, 1.4404 or 1.4436; 2) A multi-ply wall of layers of films and fabrics

33、made of thermoplastics that in combination give the required properties specified in Table 1 and provide a complete seal; 3) An external wire helix of stainless steel conforming to EN 10088-3, numbers 1.4306, 1.4401, 1.4404 or 1.4436. b) Class B: 1) An internal wire helix of stainless steel conformi

34、ng to EN 10088-3, numbers 1.4401, 1.4404 or 1.4436; 2) A multi-ply wall of layers of films and fabrics made of thermoplastics that in combination give the required properties specified in Table 1 and provide a complete seal; 3) An external wire helix of stainless steel conforming to EN 10088-3, numb

35、ers 1.4401, 1.4404 or 1.4436. BS EN 13766:2010EN 13766:2010 (E) 6 NOTE By agreement between manufacturer and purchaser, the outer layer may have colour identification. Key 1 internal wire 2 film 3 fabric 4 external wire Figure 1 Section of a typical thermoplastic multilayer hose 6 Dimensions 6.1 Int

36、ernal diameters, with tolerances and minimum bend radii When measured in accordance with EN ISO 4671, the values of the internal diameter of the hose shall conform to Table 2. When tested by the method described in EN ISO 1746 the value of the minimum bend radius shall be as given in Table 2. The ho

37、se shall show no sign of permanent deformation of the cross section i.e. kinking. Table 2 Dimensions and minimum bend radius Dimensions in millimetres Internal diameter Tolerance Minimum bend radius 25 1 150 32 1 175 38 1 175 40 1 200 50 1 200 65 2 200 75 2 250 80 2 250 100 2 500 150 2 660 200 3 910

38、 250 3 2 500 BS EN 13766:2010EN 13766:2010 (E) 7 6.2 Tolerance on length When tested in accordance with EN ISO 4671 the tolerance on the measured length of delivered hose assemblies shall be %21+. 7 Performance requirements of hoses and hose assemblies 7.1 Film and fabric When tested at the minimum

39、temperature, Type 1: 50 3 C and Type 2: 196 5 C (and in accordance with EN ISO 13934-1 or equivalent for fabric testing and EN ISO 527-1 or equivalent for film testing ) samples of film and fabric shall have an elongation at break of not less than 10 %. 7.2 Hoses When tested in accordance with the m

40、ethods given in Table 3, the physical properties of the hoses shall conform to Table 3. Table 3 Physical properties of hoses Property Unit Requirement Method Proof pressure Bar No leakage or other signs of damage at pressure given in Table 1 EN ISO 1402 with pressure increase not less than 1,7 bar/m

41、in Change in length at proof pressure (max) % 10 EN ISO 1402:2009, 8.2 initial length measured when the hose is pressurised to 0,7 bar Twist at proof pressure (max) /m 10 EN ISO 1402:2009, 8.2 initial reading taken when hose is pressurised to 0,7 bar Burst pressure Bar Values in Table 1 EN ISO 1402

42、Bend No leakage or visible damage when the hose is bent to radius given in Table 2 and subjected to the proof pressure. EN ISO 1746 Crush recovery (max) % 3 Annex A Ozone resistance 72 h at 40 C No cracking observed at 2 magnification EN ISO 7326 Thermal ageing No leakage at proof pressure given in

43、Table 1 Annex B Low temperature flexibility Test at minimum temperature given in Table 1 EN ISO 4672 BS EN 13766:2010EN 13766:2010 (E) 8 7.3 End fittings End fittings and metallic ferrules shall be made from the following materials depending on the type of hose to be used in the assembly: Type 1 hos

44、e: LT (low temperature) grade carbon steel or stainless steel; Type 2 hose: austenitic stainless steel tested in accordance with Annex C. For all types of end fittings, that part of the fitting that enters the hose and forms the means by which the fitting is connected to the hose shall be provided w

45、ith scrolls or protrusions on the surface that correspond to the pitch of the internal helix wire of the hose. 7.4 Hose assemblies Hose assemblies shall be fitted with end fittings as described in 7.3. End fittings shall be attached to the hose by one of the following methods: a) by the use of a sea

46、l and a metal ferrule which is swaged or crimped; b) by the use of a thermoset resin e.g. epoxy and a metal ferrule which is swaged or crimped. NOTE Hoses should be assembled by the hose manufacturer. When tested by the methods given in Table 4, hose assembly shall conform to Table 4. When assembled

47、 to a hose there shall be electrical continuity between the end fitting and the internal and external wires. BS EN 13766:2010EN 13766:2010 (E) 9 Table 4 Physical properties of hose assemblies Property Unit Requirements Method(s)Proof pressure Bar No leakage or other signs of weakness at pressure giv

48、en in Table 1 EN ISO 1402 with a pressure increase not less than 1,7 bar/min Bend No leakage or visible damage when the hose is bent to the radius given in Table 2 and is subjected to the proof pressure EN ISO 1746 Series of hydrostatic tests Bar % o/m burst pressure given in Table 1 Change in lengt

49、h as in Table 3 Twist as given in Table 3 Annex D Security of end fitting Bar No leakage at proof pressure given in Table 1 Annex E and EN ISO 1402 Electrical resistance between end fittings No reduction of electrical resistance between end fittings 50 2 000 BS EN 13766:2010EN 13766:2010 (E) 12 Key 1 test force, F 2 test plate 3