EN 13523-4-2014 en Coil coated metals - Test methods - Part 4 Pencil hardness《线圈包覆金属 测试方法 第4部分 铅笔硬度》.pdf

《EN 13523-4-2014 en Coil coated metals - Test methods - Part 4 Pencil hardness《线圈包覆金属 测试方法 第4部分 铅笔硬度》.pdf》由会员分享，可在线阅读，更多相关《EN 13523-4-2014 en Coil coated metals - Test methods - Part 4 Pencil hardness《线圈包覆金属 测试方法 第4部分 铅笔硬度》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS EN 13523-4:2014Coil coated metals TestmethodsPart 4: Pencil hardnessBS EN 13523-4:2014 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 13523-4:2014.It supersedes BS EN 13523-4:2001 which is withdrawn.The UK participation in its prepar

2、ation was entrusted to TechnicalCommittee STI/21, Surface preparation of steel.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correc

3、tapplication. The British Standards Institution 2014. Published by BSI StandardsLimited 2014ISBN 978 0 580 80218 8ICS 17.040.20; 25.220.60Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and

4、 Strategy Committee on 31 August 2014.Amendments issued since publicationDate Text affectedBS EN 13523-4:2014EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13523-4 July 2014 ICS 25.220.60 Supersedes EN 13523-4:2001English Version Coil coated metals - Test methods - Part 4: Pencil hardness Tles

5、 prlaques - Mthodes dessai - Partie 4: Duret crayon Bandbeschichtete Metalle - Prfverfahren - Teil 4: Bleistifthrte This European Standard was approved by CEN on 14 June 2014. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this Eur

6、opean Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versio

7、ns (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, B

8、elgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Swi

9、tzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN natio

10、nal Members. Ref. No. EN 13523-4:2014 EBS EN 13523-4:2014EN 13523-4:2014 (E) 2 Contents Page Foreword 3 1 Scope 5 2 Normative references 5 3 Terms and definitions .5 4 Principle 5 5 Apparatus and materials .5 6 Sampling .6 7 Test panels .6 8 Procedure .6 9 Expression of results 7 10 Precision .7 11

11、Test report 8 Bibliography 9 BS EN 13523-4:2014EN 13523-4:2014 (E) 3 Foreword This document (EN 13523-4:2014) has been prepared by Technical Committee CEN/TC 139 “Paints and varnishes”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard,

12、either by publication of an identical text or by endorsement, at the latest by January 2015 and conflicting national standards shall be withdrawn at the latest by January 2015. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN a

13、nd/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 13523-4:2001. The main technical changes are: a) the definition of pencil hardness was amended; b) the term “remove the coating” was corrected to “scratch the coating” in the descri

14、ption of the result of the test; c) a remark on preconditioning was added; d) concerning the applicability of the pencil hardness test, a reference to EN ISO 15184 was added. EN 13523, Coil coated metals Test methods, consists of the following parts: Part 0: General introduction Part 1: Film thickne

15、ss Part 2: Gloss Part 3: Colour difference Instrumental comparison Part 4: Pencil hardness Part 5: Resistance to rapid deformation (impact test) Part 6: Adhesion after indentation (cupping test) Part 7: Resistance to cracking on bending (T-bend test) Part 8: Resistance to salt spray (fog) Part 9: Re

16、sistance to water immersion Part 10: Resistance to fluorescent UV radiation and water condensation Part 11: Resistance to solvents (rubbing test) Part 12: Resistance to scratching BS EN 13523-4:2014EN 13523-4:2014 (E) 4 Part 13: Resistance to accelerated ageing by the use of heat Part 14: Chalking (

17、Helmen method) Part 15: Metamerism Part 16: Resistance to abrasion Part 17: Adhesion of strippable films Part 18: Resistance to staining Part 19: Panel design and method of atmospheric exposure testing Part 20: Foam adhesion Part 21: Evaluation of outdoor exposed panels Part 22: Colour difference Vi

18、sual comparison Part 23: Resistance to humid atmospheres containing sulfur dioxide Part 24: Resistance to blocking and pressure marking Part 25: Resistance to humidity Part 26: Resistance to condensation of water Part 27: Resistance to humid poultice (Cataplasm test) Part 29: Resistance to environme

19、ntal soiling (Dirt pick-up and striping) According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yu

20、goslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 13523-4:2014EN 13523-4:2014 (E) 5 1 Scop

21、e This part of EN 13523 describes the procedure to assess the relative hardness of an organic coating on a metallic substrate, by means of pencils of known hardness. Smooth surfaces will give more accurate results but the method is also applicable for textured surfaces. The more pronounced the textu

22、re, the greater the unreliability of results. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition o

23、f the referenced document (including any amendments) applies. EN 13523-0:2014, Coil coated metals Test methods Part 0: General introduction EN 23270, Paints and varnishes and their raw materials - Temperatures and humidities for conditioning and testing (ISO 3270) 3 Terms and definitions For the pur

24、poses of this document, the terms and definitions given in EN 13523-0:2014 and the following apply. 3.1 pencil hardness resistance of the coating surface to scratching when a pencil with a specified dimension, shape and hardness of the lead is pushed across the surface 4 Principle The coating is int

25、entionally damaged by pencils of increasing hardness. The hardest lead which does not scratch the coating for a minimum of 3 mm length determines the degree of hardness. 5 Apparatus and materials Ordinary laboratory apparatus, together with the following: 5.1 Set of CretacolorTMor Faber Castell draw

26、ing pencils1)or their equivalents in the following range: 6B, 5B, 4B, 3B, 2B, B, HB, F, H, 2H, 3H, 4H, 5H, 6H (softer) (harder) 1) Cretacolor is the trade name of a product supplied by Brevillier b) a reference to this part of EN 13523 (EN 13523-4); c) identification of the pencils used; d) whether

27、a mechanical device has been used; e) the results of the test, as indicated in Clause 9; f) any deviation from the test method specified; g) any unusual features (anomalies) observed during the test; h) the date of the test. BS EN 13523-4:2014EN 13523-4:2014 (E) 9 Bibliography EN 1396, Aluminium and

28、 aluminium alloys - Coil coated sheet and strip for general applications - Specifications EN 10169, Continuously organic coated (coil coated) steel flat products Technical delivery conditions EN ISO 15184:2012, Paints and varnishes - Determination of film hardness by pencil test (ISO 15184:2012) Thi

29、s page deliberately left blankThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are publis

30、hed by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The

31、 knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledg

32、e that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and internationa

33、l standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.SubscriptionsOur range of subscription services are designed to mak

34、e using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always

35、 be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automa

36、tically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences ca

37、n cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We continually improve the qualit

38、y of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.CopyrightAll the data, software and documentation set out in all British Standards and other BSI publications are the

39、property of and copyrighted by BSI, or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use. Except as permitted under the Copyright, Designs and Paten

40、ts Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. Details and advice can be obtained from the Copyright & Licensing Department.Useful Contacts:Customer ServicesTel: +44 845 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 845 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW