EN 13523-2-2014 en Coil coated metals - Test methods - Part 2 Gloss《线圈包覆金属 测试方法 第2部分 注释》.pdf

《EN 13523-2-2014 en Coil coated metals - Test methods - Part 2 Gloss《线圈包覆金属 测试方法 第2部分 注释》.pdf》由会员分享，可在线阅读，更多相关《EN 13523-2-2014 en Coil coated metals - Test methods - Part 2 Gloss《线圈包覆金属 测试方法 第2部分 注释》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS EN 13523-2:2014Coil coated metals TestmethodsPart 2: GlossBS EN 13523-2:2014 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 13523-2:2014.It supersedes BS EN 13523-2:2001 which is withdrawn.The UK participation in its preparation was

2、entrusted to TechnicalCommittee STI/21, Surface preparation of steel.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplicati

3、on. The British Standards Institution 2014. Published by BSI StandardsLimited 2014ISBN 978 0 580 80217 1ICS 25.220.60Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee o

4、n 30 June 2014.Amendments issued since publicationDate Text affectedBS EN 13523-2:2014EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13523-2 June 2014 ICS 25.220.60 Supersedes EN 13523-2:2001English Version Coil coated metals - Test methods - Part 2: Gloss Tles prlaques - Mthodes dessai - Part

5、ie 2: Brillant Bandbeschichtete Metalle - Prfverfahren - Teil 2: Glanz This European Standard was approved by CEN on 7 May 2014. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standar

6、d without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any

7、other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republ

8、ic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN C

9、OMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13523-2:2014 EBS EN 13

10、523-2:2014EN 13523-2:2014 (E) 2 Contents page Foreword 3 Introduction .5 1 Scope 6 2 Normative references 6 3 Terms and definitions .6 4 Principle 6 5 Apparatus .6 6 Sampling .6 7 Test panels .7 8 Procedure .7 8.1 Selection of the measuring geometry7 8.2 Calibration 7 8.3 Measurement 7 9 Expression

11、of results 7 10 Precision .7 11 Test report 7 Bibliography 9 BS EN 13523-2:2014EN 13523-2:2014 (E) 3 Foreword This document (EN 13523-2:2014) has been prepared by Technical Committee CEN/TC 139 “Paints and varnishes”, the secretariat of which is held by DIN. This European Standard shall be given the

12、 status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2014, and conflicting national standards shall be withdrawn at the latest by December 2014. Attention is drawn to the possibility that some of the elements of this document may be

13、the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 13523-2:2001. The main technical changes are: a) the text was aligned with the revision of EN ISO 2813, i.e. the result of the measurement is expr

14、essed in gloss units (GU); b) the definition for specular gloss was deleted; c) for calibration of the glossmeter, a reference to EN ISO 2813 was added; d) a remark on preconditioning was added; e) the procedure was amended so that measurements can be taken in the rolling direction or perpendicular

15、to the rolling direction, which has to be stated in the test report; f) the selection of the measuring geometry was aligned with the revision of EN ISO 2813. g) for precision data, a reference to EN ISO 2813 was added. EN 13523, Coil coated metals Test methods, consists of the following parts: Part

16、0: General introduction Part 1: Film thickness Part 2: Gloss Part 3: Colour difference Instrumental comparison Part 4: Pencil hardness Part 5: Resistance to rapid deformation (impact test) Part 6: Adhesion after indentation (cupping test) Part 7: Resistance to cracking on bending (T-bend test) Part

17、8: Resistance to salt spray (fog) Part 9: Resistance to water immersion Part 10: Resistance to fluorescent UV radiation and water condensation BS EN 13523-2:2014EN 13523-2:2014 (E) 4 Part 11: Resistance to solvents (rubbing test) Part 12: Resistance to scratching Part 13: Resistance to accelerated a

18、geing by the use of heat Part 14: Chalking (Helmen method) Part 15: Metamerism Part 16: Resistance to abrasion Part 17: Adhesion of strippable films Part 18: Resistance to staining Part 19: Panel design and method of atmospheric exposure testing Part 20: Foam adhesion Part 21: Evaluation of outdoor

19、exposed panels Part 22: Colour difference Visual comparison Part 23: Resistance to humid atmospheres containing sulfur dioxide Part 24: Resistance to blocking and pressure marking Part 25: Resistance to humidity Part 26: Resistance to condensation of water Part 27: Resistance to humid poultice (Cata

20、plasm test) Part 29: Resistance to environmental soiling (Dirt pick-up and striping) According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Re

21、public, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS

22、 EN 13523-2:2014EN 13523-2:2014 (E) 5 Introduction In EN 1396 and EN 10169, tolerances against nominal gloss are given for different gloss ranges of the coil coated product. BS EN 13523-2:2014EN 13523-2:2014 (E) 6 1 Scope This part of EN 13523 specifies the procedure for determining the gloss of an

23、organic coating on a metallic substrate. Gloss is a characteristic of fundamental importance to the appearance of the coil coated product. The apparatus requires a flat specimen of size greater than the aperture, thus, uneven surfaces cannot be measured. This method is applicable to all pigmented an

24、d unpigmented coatings including metallic/pearlescent coatings. However, for textured coatings it is only indicative. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only

25、 the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 13523-0:2014, Coil coated metals Test methods Part 0: General introduction EN 23270, Paints and varnishes and their raw materials Temperatures and humidities for c

26、onditioning and testing (ISO 3270) EN ISO 2813, Paints and varnishes Determination of specular gloss of non-metallic paint films at 20, 60 and 85 (ISO 2813) 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 13523-0:2014 and the following apply. 3.1 glos

27、s optical property of a surface, characterized by its ability to reflect light specularly SOURCE: FprEN ISO 4618:2014, 2.132, modified, Note 1 to entry deleted 4 Principle The gloss of the organic coating is determined by measuring the specular reflectance. The angle of incident light is usually 60,

28、 but angles of 20 or 85 may be used for more accurate measurement of high or low gloss values. 5 Apparatus Ordinary laboratory apparatus, together with the following: 5.1 60 glossmeter or multi-angle glossmeter, in accordance with EN ISO 2813. 5.2 Calibration standards, as recommended by the manufac

29、turer of the glossmeter, in accordance with EN ISO 2813. 6 Sampling See EN 13523-0. BS EN 13523-2:2014EN 13523-2:2014 (E) 7 7 Test panels See EN 13523-0. 8 Procedure 8.1 Selection of the measuring geometry Specify the optimum reflector geometry based on a measurement of the sample with the 60 geomet

30、ry: The 60 geometry is applicable to all paint films, but for very high gloss and near-matt films 20 or 85 might be more suitable. The 20 geometry is intended to give improved differentiation between high-gloss paint films, i.e. films with a 60 gloss higher than about 70 GU (gloss units). The 85 geo

31、metry is intended to give improved differentiation between low-gloss paint films, i.e. films with a 60 gloss lower than about 10 GU (gloss units). 8.2 Calibration Adjust the instrument with a high-gloss reference standard to the assigned gloss value, as specified in EN ISO 2813. 8.3 Measurement Meas

32、ure the gloss at ambient temperature. For more accurate measurements, as required for instance in case of dispute, the temperature shall be (23 2) C and the relative humidity (50 5) %, in accordance with EN 23270. Conditioning is carried out in accordance with EN 13523-0:2014, Clause 6. The gloss ma

33、y be measured in the rolling direction or perpendicular to the rolling direction. The direction of measurement shall be stated in the test report. Place the instruments aperture over the coated specimen and note the gloss reading. Take readings at not less than three different parts of the coated sp

34、ecimen at the specified geometry (60, 20 or 85). Report the gloss as the average of these readings and report the geometry used if it is not 60. 9 Expression of results Express the result of the measurements in gloss units (GU), as the average of the readings taken. 10 Precision For precision data s

35、ee EN ISO 2813. 11 Test report The test report shall contain at least the following information: a) all details necessary to identify the product tested; b) a reference to this part of EN 13523 (EN 13523-2); c) the geometry used if it is not 60; d) whether the measurement has been taken in the rolli

36、ng direction or perpendicular to the rolling direction; BS EN 13523-2:2014EN 13523-2:2014 (E) 8 e) the results of the test, as indicated in Clause 9; f) any deviation from the test method specified; g) any unusual features (anomalies) observed during the test; h) the date of the test. BS EN 13523-2:

37、2014EN 13523-2:2014 (E) 9 Bibliography 1 EN 1396, Aluminium and aluminium alloys - Coil coated sheet and strip for general applications - Specifications 2 EN 10169:2010+A1:2012, Continuously organic coated (coil coated) steel flat products - Technical delivery conditions 3 FprEN ISO 4618:2014, Paint

38、s and varnishes Terms and definitions (ISO/FDIS 4618:2014) This page deliberately left blankThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. B

39、ritish Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry, government, consumers, innovators and others to shape their combine

40、d experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goal

41、s.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publica

42、tions, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.Subsc

43、riptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desk

44、top. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating

45、 service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are abl

46、e to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updat

47、ed by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.CopyrightAll the data, software and documentation set ou

48、t in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and u

49、se. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. Details and advice can be obtained from the Copyright & Licensing Department.U