EN 12773-1999 en Footwear - Test Methods for Outsoles - Needle Tear Strength《鞋类 鞋底试验方法 针刺裂强度》.pdf

《EN 12773-1999 en Footwear - Test Methods for Outsoles - Needle Tear Strength《鞋类 鞋底试验方法 针刺裂强度》.pdf》由会员分享，可在线阅读，更多相关《EN 12773-1999 en Footwear - Test Methods for Outsoles - Needle Tear Strength《鞋类 鞋底试验方法 针刺裂强度》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、STD-BSI BS EN 12773-ENGL 2000 W Lb24bb9 0830246 994 W BRITISH STANDARD Footwear - Test methods for outsoles - Needle tear strength The European Standard EN 127731999 has the status of a British Standard NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW LS EN 2773:ZOOO STD-BSI BS

2、 EN L2773-ENGL 2000 Lh24bh9 0830247 820 H Amd. No. BS EN 12773:2000 Date Comments National foreword This British Standard is the official English language version of EN 127731999. The UK participation in its preparation was entrusted to Technical Committee TCV69, Footwear and leather, which has the

3、responsibility to: - aid enquirers to understand the text; - present to the responsible European committee any enquiries on the - monitor related international and European developments and promulgate interpretation, or proposals for change, and keep the UK interests informed; them in the UK A list

4、of orgamizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International

5、 Standards Correspondence Index”, or by using the “Find facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British S

6、tandard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a Cont cover, an inside hnt cover, the EN title page, pages 2 to 7 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. This Briti

7、sh Standard, having been prepared under the direction of the Sector Committee for Materials and Chemicals, was published under the authority of the Standards Committee and comes into effect on 15 Febniary 2000 O BSI 02-2000 ISBN O 580 35616 7 STD-BSI BS EN ii2773-ENGL 2000 I1624669 0830248 767 EUROP

8、EAN STANDARD EN 12773 NORME EUROPENNE EUROPISCHE NORM November 1999 ICs 61 .O60 English version Footwear - Test methods for outsoles - Needle tear strength Chaussures - Mthodes dessai applicables aux semelles dusure - Rsistance du point de couture Schuhwerk - Prfverfahren fur Laufsohlen - Nadelausre

9、ifestigkeit This European Standard was approved by CEN on 17 September 1999. CEN members are bound to comply with the CENICENELEC Internal Regulations which stipulate the conditions for giving this Europan Standard the status of a national standard without any alteration. Up-to-date lists and biblio

10、graphical references concerning sich national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by trmslation under the responsibility of a

11、 CEN member into its own language and notified to the Central Secretariat has the same status as be official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norwa

12、y, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Central Secretariat: rue de Stassart, 36 8-1050 Brussels 8 1999 CEN All rights of exploitation in any form and by any means reserved worldw

13、ide for CEN national Members. Ref. No. EN 12773:1999 E STD-BSI BS EN 12773-ENGL 2000 m 1b24bb 0830249 bT3 m Page 2 EN I 2773: I999 Contents Page Foreword . 1 Scope 2 Normative references 3 Definit ions . 4 Apparatus and material . 6 Test method . 8 Test report . 5 Sampling and conditioning 7 Express

14、ion of results OBSI 02-2000 sTD.BS1 BS EN L2773-ENGL 2000 Lb24bb 0830250 315 Page 3 EN 12773:1999 Foreword This European Standard has been prepared by Technical Committee CEN/TC 309, Footwear, the Secretariat of which is held by AENOR. This European Standard shall be given the status of a national s

15、tandard, either by publication of an identical text or by endorsement, at the latest by May 2000, and conflicting national standards shall be withdrawn at the latest by May 2000. According to the CENICENELEC Internal Regulations, the national standards organizations of the following countries are bo

16、und to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. OBSI 02-2000 STD-BSI BS EN 12773-ENGL 2000 Lb2Ybb7 0830251 251

17、m Page 4 EN 12773: 1 999 1 Scope This European Standard specifies a method for the determination of the needle tear strength for outsoles, irrespective of the material. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These

18、 normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated

19、 references the latest edition of the publication referred to applies. EN 10002-2 Metallic materials. Tensile testing - Part 2: Verification of the force measuring system of the tensile testing machines. EN 12222 Footwear - Standard atmospheres for conditioning and testing of footwear and components

20、 for footwear. prEN 13400: 1998 Footwear - Sampling location of components for footwear. 3 Definit ions For the purposes of this standard the following definition applies: 3.1 needle tear strength the quotient by division of the maximum force, occurring during tearing-out of the needle, by the thick

21、ness of the test piece 4 Apparatus and material The following apparatus and material shall be used: 4.1 Tensile-testing machine The tensile-testing machine shall comply with the requirements of EN 10002-2, to an accuracy corresponding to grade B, with a constant rate of traverse of 100 mdmin 2 10 mm

22、/min. Autographic recording of force or a maximum force pointer is recommended. Page 5 EN 12773:1999 4.2 Needle Either a smooth-surfaced steel needle of 1 mm * 0,Ol mm diameter or a corresponding piece of spring steel wire, ground to a point. 4.3 Clamping device Figure 1 shows an example of a clampi

23、ng device. The distance between the support links for the needle shall be adjustable, so that it can be adjusted to the thickness of the specimen. The clamping device shall be equipped with a suitable protective device to prevent the needle from jumping out. 4.4 Thickness gauge Thickness gauge, stan

24、ding on a firm base and loaded with a dead weight such that the presser foot applies a pressure of 10 kPa A 3 kPa. The gauge has a presser foot which is flat, circular and 1 O mm f O, 1 mm in diameter. The gauge has a scale division of 0,Ol mm. 5 Sampling and conditioning The test pieces to be teste

25、d are taken in accordance with prEN 13400:1998. All test pieces shall be conditioned according to EN 12222 before testing for a minimum of 24 h. Test pieces are strips of 50 mm * 1 mm length and 20 mm f 1 mm width. The thickness of the test piece shall be preferably: - 2,O mm f 0,2 mm for polymeric

26、and elastomeric compact outsoles; - 4,O mm f 0,2 mm for semi-expanded and cellular outsoles; - for leather outsoles the original thickness shall be tested. The test is being performed with at least three specimens. Their uniform thickness (see specification below) shall be obtained by means of an ap

27、propriate splitting machine. If feasible, smooth original “skin” surfaces of the sample shall remain unchanged in the specimens. This leads to three possible types of specimen: Specimen with 2 original “skins” - S 2 Specimen with 1 original “skin” - S 1 Specimen with no original “skin” - S O The fin

28、al result shall be based only on specimens of the same type, which shall be stated in the report. OBSI 02-2000 _ STD-BSI BS EN 12773-ENGL 2000 W 1b24bb9 0830253 024 W Page 6 EN 12773: 1 999 6 Test method Measure the thickness of the test piece, using the thickness gauge (see 4.4). Pierce the piece w

29、ith a needle of 1 mm diameter (see 4.2), 5 mm from the edge at the centre of the narrow side (see Figure l), as nearly perpendicular as possible with the aid of a template. The piece shall not have been previously bored or punched. Place the needle, which is now stuck in the piece, in the clamping d

30、evice (see 4.3). The distance between the support links shall be adjusted so that they just touch the piece. Clamp the lower end of the piece in the lower grip (shown in Figure 1 as a scissors-clamp). Stress the piece with a feed-rate of 100 mm/min f 10 mdmin on the clamps. Read off the maximum stre

31、ngth in newtons which occurs during the tearing-out of the needle. 7 Expression of results The needle tear strength Ss expressed in newtons per millimetres of thickness is given by the formula Ss = F/d where F is the maximum force in newtons d is the thickness in millimetres The result will be the a

32、verage of the three determinations. 8 Testreport The test report shall include the following information: results, expressed in accordance with clause 7; thickness of the test pieces; full description of the samples tested including commercial styles, codes, colours, nature, etc.; reference to this

33、method of test; date of testing; any deviation from this test method. OBSI 02-2000 STD*BSI BS EN 12773-ENGL 2000 W 1624667 0830254 ThO Page 7 EN 12773: 1999 Dimensions in mm Support links ieedle Figure 1 - Example of clamping device OBSI 02-2000 STD-BSI BS EN L2773-ENGL 2000 Lb24669 0830255 9T7 BS E

34、N 12773:2000 BSI 389 Chiswick High Road London w4 4AL BSI - British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions Br

35、itish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity

36、while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel O20 8996 9OOO. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers autom

37、atically receive the latest editions of standards. Buying standards Orders for all BSI, intedonal and foreign standards publications should be addressed to Customer Services. Tel 020 8996 9001. Fax: 020 8996 7001. in response to orders for international standards, it is BSI policy to supply the BSI

38、implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of mformation on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electroni

39、c information services are also available which give details on ail its products and services. Contact the Infomation Centre. Tel 020 8996 7111. Fax: O20 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of s

40、tandards. For details of these and other benefits contact Membership Am on. Tel 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under

41、 the Copynght, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or bammitted in any form or by any means - electronic, photocopying, recording or otherwise - without prior written permission from BSI. This does not preclude the free use, in the course of implem

42、enting the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Detaiis and advice can be obtained from the Copyright Manager. Tel 020 8996 7070.