EN 12241-1999 en Touch and Close Fasteners - Method for Closure Prior to Washing and Drying or Dry Cleaning《接触锁扣 洗 干燥或干洗前的锁紧方法》.pdf

《EN 12241-1999 en Touch and Close Fasteners - Method for Closure Prior to Washing and Drying or Dry Cleaning《接触锁扣 洗 干燥或干洗前的锁紧方法》.pdf》由会员分享，可在线阅读，更多相关《EN 12241-1999 en Touch and Close Fasteners - Method for Closure Prior to Washing and Drying or Dry Cleaning《接触锁扣 洗 干燥或干洗前的锁紧方法》.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、 BS EN 12241:2000 STD-BSI BS EN IiZZqL-ENGL 2000 6 Lb24hL9 0822585 2b3 II BRITISH STANDARD Touch and close fasteners - Method for closure prior to washing and drying or dry cleaning The European Standard EN 12241:1999 has the status of a British Standard ICs 61.040 NO COPMNG WITHOUT BSI PERMISSION E

2、XCEPT AS PERMITTED BY COPYRIGHT LAW STD-BSI BS EN 12241-ENGL 2000 W Lb24bb9 08225Bh LTT BS EN 12241:2000 Amd.No. National foreword Date Comments This British Standard is the English language version of EN 12241: 1999. The UK participation in its preparation was entrusted to Technical Committee TCV75

3、, Fastenings, which has the responsibility to: - aid enquirers to understand the text; - present to the responsible European committee any enquiries on the - monitor related international and European developments and promulgate interpretation, or proposals for change, and keep the UK interests info

4、rmed them in the UK. A list of organizations represented on this committee can be obtained on request to its secrem. Cross-references The British Standards which implement intemational or European publications referred to in this document may be found in the BSI Stan its width should be chosen in ac

5、cordance with the specific density of the phosphor-bronze used in its manufacture. 4.2 Set of forks with a handle (see Figure 2) which engages the metal roller (4.1), and allows the roller to be moved without any extra down force being applied (see Figure 3). 4.3 Flat surface (for example a table) O

6、BSI 01-2000 - STD=BSI BS EN 122Yl-ENGL 2000 lb24bb7 0822570 hZ0 9 Page 4 EN 12241:1999 5 Test specimens Cut sufficient test specimens, in number and length, from both the male and female tapes in accordance with the requirements of any subsequent test method. 6 Conditioning Condition the test specim

7、ens for a minimum of 24 h, in accordance with the standard temperate atmosphere for testing, as specified in EN 20139. The closing of the test specimens and the testing of the tapes shall also take place under these conditions. 7 Procedure Make each closure as follows. Place the male tape on the fla

8、t surface with the pile uppermost and then place the female tape on top with the pile facing downwards so that the full length and width of the tapes make a closure, using minimal hand pressure. Traverse the metal roller (4.1), at a rate of approximately 200 mds, along the tapes in one direction the

9、n immediately reverse and traverse in the other direction then turn the mating tapes over. Repeat the procedure until the roller has traversed the mating tapes five times in each direction, i.e. a total of ten times. Take care that the centre of gravity of the roller does not deviate from the centre

10、 line of the tapes during this operation. Take care that the roller covers the entire width of the mating tapes NOTE: The tapes are turned over to minimize curvature. 8 Test report Report the following information: a) number and date of this European Standard; b) date of the test; c) identification

11、of the touch and close fastener tapes; d) any deviation from this standard and any incident likely to have affected the results. OBSI 01-2000 STDmBSI BS EN LZZLiL-ENGL 2000 W Lb2Libb7 0822573 5b7 4 c4 I I I Page 5 EN 12241:1999 Dimensions in millimetres Key: 1 Choose roller width to meet specified m

12、ass Figure 1: Metal roller Dimensions in millimetres Key: 1 Handle 2 Forks 3 Space between the forks to be 2 mm greater than the roller width Figure 2: Set of forks with a handle OBSI 01-2000 STD-BSI BS EN L224L-ENGL 2000 m Lb24bb7 0822592 4T3 m Page 6 EN 12241:1999 I I I I Figure 3: Rolling mechani

13、sm for touch and close fasteners OBSI 01-2000 12241:2000 BSI 389 Chiswick High Road London w4 4AL STD - BSI BSI - British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the LJK view on standards in Europe and at the international l

14、evel. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant ahn of BSI to improve the quaiity of our products and services. We would be

15、grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside nont cover. Tel: O20 8996 9OOO. Fax: 020 8996 7400. BSI offers members an individual updating se

16、rvice called PLUS which ensures that subscribeis automatidly receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addresed to Customer Services. Tek O20 8996 9001. Fax: O20 8996 7001. In response to orders for inter

17、national standards, it is BSI policy to supply the BSI implementation of those that have been published as British standards, unless otherwise requested. Information on standards ES1 provides a wide range of infodon on national, European and international standards through its Library and its Techni

18、d Help to Exporters Service. Various ES1 eleclxonic infomation services are also available which give details on all its products and services. Contact the Informakion Centre. Tel: 020 8996 7111. Fax: O20 8996 7048. Subscribing members of BSI are kept up to date with standards developments and recei

19、ve substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership A- on. Tel: O20 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. ES1 also holds the copyright, in the UK, of the publications of the internation

20、al standardization bodies. Except as permitted under the Copynght, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or tsansmittd in any form or by any means - electronic, photocopying, recording or otherwise - without prior written permission fiom BSI. This do

21、es not preclude the i-ee use, in the come of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Dem and advice can be obtained fi-om the Copyright Manager. Tel 020 8996 7070.