EN 10132-3-2000 en Cold Rolled Narrow Steel Strip for Heat Treatment - Technical Delivery Conditions - Part 3 Steels for Quenching and Tempering《热处理用冷轧窄钢带 交货技术条件 第3部分 淬火和回火钢［代替 GME.pdf

《EN 10132-3-2000 en Cold Rolled Narrow Steel Strip for Heat Treatment - Technical Delivery Conditions - Part 3 Steels for Quenching and Tempering《热处理用冷轧窄钢带 交货技术条件 第3部分 淬火和回火钢［代替 GME.pdf》由会员分享，可在线阅读，更多相关《EN 10132-3-2000 en Cold Rolled Narrow Steel Strip for Heat Treatment - Technical Delivery Conditions - Part 3 Steels for Quenching and Tempering《热处理用冷轧窄钢带 交货技术条件 第3部分 淬火和回火钢［代替 GME.pdf（15页珍藏版）》请在麦多课文档分享上搜索。

1、 STD.BSI BS EN LOL32-3-ENGL 2000 Lb24bb 0851175 5T8 BRITISH STANDARD Cold rolled narrow steel strip for heat treatment - Technical delivery conditions - Part 3: Steels for quenching and tempering The European Standard EN 10132-2:2000 has the status of a British Standard ICs 77.140.10; 77.140.50 BS E

2、N 10 132-3 :2000 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYBIGHT LAW COPYRIGHT European Committee for StandardizationLicensed by Information Handling Services STDmBSI BS EN LOL32-3-ENGL 2000 Lh24hh9 OBSLL76 Y34 BS EN 10132-3:2000 been prepared under the direction of the Engineerin

3、g Amd.No. Sector Committee, was published under the authority of the Standards Committee and comes into effect on 15 May 2000 O BSI 052000 ISBN O 580 36851 8 National foreword Date Comments This British Standard is the officiai English language version of EN 101323:2000. Together with BS EN 10132-1

4、and BS EN 10132-2, it supersedes BS 1449-1.151991 which is withdrawn. The UK participation in its preparation was enmsted to Technical Committee ISE/31, Wrought steels, which has the responsibility to. - aid enquirers to understand the text; - present to the responsible European committee any enquir

5、ies on the - monitor related international and European developments and promulgate interpretation, or proposals for change, and keep the UK interests informed; them in the UK A list of organizations represented on this committee can be obtained on request to its secretaxy. Cross-references The Brit

6、ish Standards which implement internationai or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index“, or by using the “Find“ facility of the BSI Standards Electronic Catalogue. A Britis

7、h Standard does not purport to include all the necessary provisions of a contract. Users of British Standasds ase responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front

8、cover, an inside front cover, the EN title page, pages 2 to 12, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. COPYRIGHT European Committee for StandardizationLicensed by Information Handling ServicesEUROPEAN ST

9、ANDARD NORME EUROPENNE EUROPISCHE NORM STD.BSI BS EN LOL32-3-ENGL 2000 11624669 08SLL77 370 H EN 101323 February 2000 ICs 77.140.10; 77.140.50 English version Cold rolled narrow steel strip for heat treatment - Technical delivery conditions - Part 3: Steels for quenching and tempering Feuillards lam

10、ins froid pour traitement thermique - Conditions techniques de livraison - Partie 3: Acier pour trempe et revenu Kaltband aus Stahl for eine Warmebehandlung - Technische Lieferbedingungen - Teil 3: Vergtungssthle This European Standard was approved by CEN on 3 January 2000. CEN members are bound to

11、comply with the CENKENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning sich national standards may be obtained on application to the Central

12、Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by trmslation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as he of

13、ficial versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COM

14、ITE EUROPEEN DE NORMALISATION EUROPISCHES KOMITEE FUR NORMUNG Central Secretariat: rue de Stassart, 36 8-1050 Brussels O 2000 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 10132-3:2000 E COPYRIGHT European Committee for Standardi

15、zationLicensed by Information Handling ServicesPage 2 EN 1 O1 32-3:2000 Contents Foreword 1 2 3 4 4.1 4.2 5 6 7 7.1 7.2 7.3 7.4 7.5 7.6 7.7 7.8 a 9 10 11 12 Scope Normative references Terms and definitions Classification and designation Classification Designation Information to be supplied by the pu

16、rchaser Manufacturing process Requirements General Method of delivery Delivery condition Chemical composition Mechanical properties Structure Surface finish Dimensions and tolerances on dimensions and shape Inspection Sampling Test methods Labelling, packaging and protection Retests Annex A (informa

17、tive): Technical information on steels for quenching and tempering Annex B (informative): List of corresponding former national designations 207 M Page 3 4 4 4 4 4 4 4 4 5 5 5 5 5 5 6 6 6 6 6 6 7 7 10 12 OBSI 05-2000 COPYRIGHT European Committee for StandardizationLicensed by Information Handling Se

18、rvicesSTDoBSI BS EN 10332-3-ENCL 2000 Lb24bb9 OBSLlr79 143 Page 3 EN 10132-312000 Foreword This European Standard has been prepared by Technical Committee ECISSTTC 23, Steels for heat treatment, alloy steels and free-cutting steels - Qualities and dimensions, the secretariat of which is held by DIN.

19、 This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by August 2000, and conflicting national standards shall be withdrawn at the latest by August 2000. According to the CENICENELEC Internal Regulations,

20、 the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United K

21、ingdom. The European Standard EN 1 O1 32, Cold rolled narrow steel strip for heat-treatment - Technical delivery conditions, is subdivided as follows: Part 1 : General; Part 2: Case hardening steels; Part 3: Steels for quenching and tempering; Part 4: Spring steels and other special applications. OB

22、SI 05-2000 COPYRIGHT European Committee for StandardizationLicensed by Information Handling ServicesPage 4 EN 10132-312000 1 Scope I .I This part of EN 1 O1 32 applies to non-alloy and alloy cold rolled narrow steel strip in thicknesses up to 6 mm for quenching and tempering, and in the quenched and

23、 tempered condition with thicknesses between 0,30 mm and 3,OO mm for general and for specific applications. 1.2 This EN 1 O1 32-3 is complemented by EN 1 O1 32-1. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These norma

24、tive references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated refer

25、ences the latest edition of the publication referred to applies. EN 10020, Definition and classification of grades of steel. EN I O1 32-1, Cold rolled narrow steel strip for heat treatment - Technical delivery conditions - Part I: General. EN 1 O1 40, Cold rolled narrow steel strip - Tolerances on d

26、imensions and shape. EN IS0 6508-1 , Metallic materials - Rockwell hardness test - Part I: Test method (scales A, B, C, D, E, F, G, H, K, N, T) (IS0 6508-1:1999). 3 Terms and definitions For the purposes of this standard, the terms and definitions given in EN 101 32-1 apply. 4 Classification and des

27、ignation 4.1 Classification All steels covered by this European Standard are classified according to EN 10020. Steel grades C22E, C30E, C35E, C40E, C45E, C50E, C55E, C60E and 25Mn4 are non-alloy special steels, steel grades 25CrMo4, 34CrMo4 and 42CrMo4 are alloy special steels. 4.2 Designation See E

28、N 101 32-1. 5 Information to be supplied by the purchaser See EN 1 O1 32-1. OBSI 05-2000 COPYRIGHT European Committee for StandardizationLicensed by Information Handling Services STD.BSI BS EN 10132-3-ENGL 2000 Lb24bb 085LLBL 8TJ Page 5 EN 1 O1 32-312000 6 Manufacturing process See EN 10132-1. 7 Req

29、uirements 7.1 General See EN 10132-1. 7.2 Method of delivery See EN 10132-1 7.3 Delivery condition Cold rolled narrow steel strip covered by EN 10132-3 shall be supplied in one of the following delivery conditions: - annealed or annealed and skin passed (+A or +LC); - cold rolled (+CR); - quenched a

30、nd tempered (+QT) - for the grades indicated in Table 3 of this standard. NOTE The delivery condition - annealed to achieve spheroidized carbides (+AC) - may be agreed. In such cases, limits on spheroidization and mechanical properties may also be agreed at the time of enquiry and order. 7.4 Chemica

31、l composition 7.4.1 Cast analysis The chemical composition shall be in accordance with the values specified in Table I for the cast analysis. 7.4.2 Product analysis In cases where a product analysis is requested, the admissible deviations from the values specified for the cast analysis are indicated

32、 in Table 2. 7.5 Mechanical properties The mechanical properties of the strip shall be in accordance with the values given in Table 3. For thicknesses outside this range, mechanical properties shall be agreed between the customer and the supplier. NOTE I For those customers who specify Rockwell hard

33、ness rather than Vickers hardness or tensile strength, a table is given in A.l , showing Rockwell hardness values for information. NOTE 2 For information, the minimum hardness values given in Table A.2 show the minimum values after quenching, without tempering. OBSI 05-2000 COPYRIGHT European Commit

34、tee for StandardizationLicensed by Information Handling ServicesPage 6 EN 101 32-312000 7.6 Structure 7.6.1 Grain size See EN 1 O1 32-1. 7.6.2 Non-metallic inclusions See EN 1 O1 32-1. 7.6.3 Decarburization For steels with minimum carbon contents 0,50 %, decarburization shall not exceed 3 % of the m

35、aterial thickness per side when measured at a distance of 5 mm from the strip edge (see also EN 1 O1 32-1). 7.7 Surface finish The surface finish of cold rolled steel strip shall be bright as achieved by rolling and annealing in a controlled atmosphere. The surface finishes of quenched and tempered

36、cold rolled strip are as follows: - grey/blue oxide finish: unpolished; - bright tempered: unpolished; - polished: obtained by fine grinding, abrasive brushing or other processes; - polished and coloured: blue or yellow colour obtained by oxidization by heat treatment. 7.8 Dimensions and tolerances

37、on dimensions and shape Tolerances on width for quenched and tempered strip shall be agreed between customer and supplier. For all other tolerances EN 10140 applies (see also EN 10132-1). Special edges are available by agreement between supplier and customer, and the tolerances on width for these ed

38、ges are to be agreed. 8 Inspection See EN 10132-1. 9 Sampling See EN 1 O1 32-1. 10 Test methods See EN I O1 32-1. OBSI 05-2000 COPYRIGHT European Committee for StandardizationLicensed by Information Handling Services STD.BSI BS EN 10L32-3-ENGL 2000 H Lb24bb 085LL83 b74 Page 7 EN 1 O1 32-312000 I1 La

39、belling, packaging and protection See EN 10132-1. 12 Retests See EN 1 O1 32-1. OBSI 05-2000 COPYRIGHT European Committee for StandardizationLicensed by Information Handling ServicesPage 8 EN 1 O1 32-312000 0,035 0,035 Table 1 - Chemical composition of steels for quenching and tempering (cast analysi

40、s) I I 0,035 max. 0,40 rnax. 0,lO 0,40 0,035 max.0,40 max. 0,lO 0,40 I :;Idesignailon I C22E 1.1151 0,17 to 0.24 0.40 0,40 to 0,70 I si I Mn number max. C50E C55E I 1.1178 I 0,27 to 0,34 I 0,40 I 050 to 0,80 1.1206 0,47 to 035 0,40 0,60 to 0.90 1.1203 0,512 to 0,60 0,40 0,60 to 0,90 C45E C60E 25Mn4

41、25CrMo4 34CrMo4 1.1221 0,57 to 0,65 0,40 0,60 to 0,90 1.1177 0,23 to 0,28 0.40 0,95 to 1,15 1.7218 0,22 to 0,29 0,40 0,60 to 0,90 1.7220 0,30 to 0,37 0,40 0,60 to 0,90 42CrMo4 1.7225 0,38 to 0,45 0,40 0,60 to 0,90 % by mass p I s I Cr I Mo I o;o max. max. max. 0,035 0,035 max. 0,40 rnax. 0,lO Elemen

42、t 0,035 I 0,035 I max. 0,40 I max. 0,lO I 0,40 Permissible maximum content in the cast analysis % by mass S Cr Mo 0,035 1 0,035 I max. 0,40 I max. 0,lO I 0,40 S 0,035 +0,005 5 0,40 +0,03 0,40 5 1,20 I0,04 s 0.10 +0,02 0,IO s0.30 k0.03 0,035 I 0,035 1 max. 0,40 1 max. 0,lO 1 gTg 0,035 0,035 rnax. 0,4

43、0 rnax. 0,lO 0,035 0,035 max. 0.40 rnax. 0,lO 0,035 1 0,035 1 max. 0,40 I max. 0,lO I 0,; 0,035 0,035 0,90 to 1,20 0,15 to 0,30 0,035 0,035 030 to 1,20 0,15 to OJO 0.035 I 0.035 I 0.90 to 1.20 I 0.15 to 0.30 I - a Elements not quoied in this table shall not be intentionally added to the steel withou

44、t the agreement of the purchaser, other han for the purpose of finishing the heat. All reasonable precautions shall be taken to prevent the addition, from scrap or other materialused in manufacture, of such elements which affect the hardenability, mechanical properties and application. Table 2 - Per

45、missible deviations between the product analysis and the limiting values given in Table 1 for the cast analysis Permissible deviationa % by mass 6 0,55 IC I 0,55 60,65 I0.02 I0,03 S 0,40 I +0,03 I I 6 0,035 I +0,005 I I Ni I S 0,40 I +0,04 I a f means that in one cast the deviation may occur over th

46、e upper value or under the lower value of the specified range in Table 1, but not both at the same time. OBSI 05-2000 COPYRIGHT European Committee for StandardizationLicensed by Information Handling ServicesSTD-BSI BS EN 10232-3-ENGL 2000 I Lb24bb9 0851185 447 m annealed (+A) or annealed and skin pa

47、ssed (+W Page 9 EN 1 O1 32-3:2000 cold rolled (+CR) quenched and tempered (+QT) Table 3 - Mechanical properties and hardness requirementsap name number C22E 1.1151 C30E 1.1178 C35E 1.1181 I Steel designation I delivery condition R R A HV R HV R HV N/mm2 Nimm % Nimm2 Nimm Max. max. min. max. max. max

48、. 400 500 22 155 900 265 420 520 20 165 920 270 430 540 19 170 930 275 For material supplied in the cold rolled condition, a range of 150 N/mm2 or 50 HV shall apply, e.g. 700 N/mm2 to 850 N/mm2 or eg. 200 HV to 250 HV. For material supplied in the quenched and tempered condition, a range of 150 N/mm

49、z or 50 HV shall apply, e.g. 1 150 N/mm2 to 1 300 N/mm2 or e.g. 350 HV to 400 HV. R 0,2 %-Proof strength: R Tensile strength; A Elongation on a gauge length of 80 mm; HV Vickers hardness. Cold rolled condition may be supplied on request. In this case, the mechanical properties shall be agreed at the time of enquiiy and order. OBSI 05-2000 COPYRIGHT European Committee for StandardizationLicensed by Information Handling ServicesPage 10 EN 1 O1 32-312000 name Annex A (informative) number Technical information on steels for quenching and tempering a