EN 10132-1-2000 en Cold Rolled Narrow Steel Strip for Heat Treatment - Technical Delivery Conditions - Part 1 General《热处理用冷轧窄钢带 交货技术条件 第1部分 总则》.pdf

《EN 10132-1-2000 en Cold Rolled Narrow Steel Strip for Heat Treatment - Technical Delivery Conditions - Part 1 General《热处理用冷轧窄钢带 交货技术条件 第1部分 总则》.pdf》由会员分享，可在线阅读，更多相关《EN 10132-1-2000 en Cold Rolled Narrow Steel Strip for Heat Treatment - Technical Delivery Conditions - Part 1 General《热处理用冷轧窄钢带 交货技术条件 第1部分 总则》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、STDoBSI BS EN LOL32-1-ENGL 2000 Lb24bb9 085LL43 T78 = BRITISH STANDARD Cold rolled narrow steel strip for heat treatment - Technical delivery conditions - Part 1: General The European Standard EN 10132-1:2000 has the status of a British Standard ICs 77.140.10; 77.140.50 3s EN 10132-1:2000 NO COPYING

2、 WITHOUT BSI PERMISSION EXCEPT AS PEBMITIED BY COPYRIGHT LAW COPYRIGHT European Committee for StandardizationLicensed by Information Handling ServicesSTDmBSI BS EN LOL32-L-ENGL 2000 Lb24bb9 0851144 924 BS EN 10132-1:2000 AmdNo. Date This British Standard, having been prepared under the direction of

3、the Engineering Sector Committee, was published Comments National foreword This British standard is the official English language version of EN 10132-12000. Together with Bs EN 101322 and BS EN 10132-3, it supersedes BS 1449-1.151991 which is withdrawn. Together with BS EN 10132-4 it supersedes BS 5

4、77QPartS 1,2 and 3 1981 which are withdrawn. The UK participation in its preparation was entrusted to Technical Committee ISEL31, Wmught steels, which has the responsibility to: - aid enquirem to understand the text; - present to the responsible European committee any enqyiries on the - monitor rela

5、ted international and European developments and promulgate interpretation, or proposals for change, and keep the UK interests informed; them in the UK A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The Britbh Standards which implem

6、ent intedonal or European publications referred to in this document may be found in the BSI standards Catalogue under the section entitled International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British standard does not purport to

7、include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immuniQ from legal obligations. Summary of pages This document comprises a front cover, an inside hnt cover, the

8、EN title page, pages 2 to 13 and a back cover. The BSI copyright notice displayed in this document indicate when the domment waslastissued. under the authon 77.140.50 English version Cold rolled narrow steel strip for heat treatment - Technical delivery conditions - Part 1 General Feuillards lamins

9、froid pour traitement thermique - Conditions techniques de livraison - Partie 1: Gnralitbs Kaltband aus Stahl fr eine Wrmebehandlung - Technische Lieferbedingungen - Teil 1 : Allgemeines This European Standard was approved by CEN on 3 January 2000. CEN members are bound to comply with the CENEENELEC

10、 Internal Regulations which stipulate the conditions for giving this Europeen Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning sich national standards may be obtained on application to the Central Secretariat or to any CEN

11、member. This European Standard exists in three official versions (English, French, German). A version in any other language made by tmslation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as he official versions. CEN member

12、s are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION EUROPISCHES KOMITEE FUR NORMUN

13、G COMITE EUROPEEN DE NORMALISATION Central Secretariat: rue de Stassart, 36 8-1050 Brussels Q 2000 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1 O1 32-1 :2000 E COPYRIGHT European Committee for StandardizationLicensed by Inform

14、ation Handling ServicesSTD-BSI BS EN 10132-1-ENGL 2000 I Lb24bb 085114b .T m Page 2 EN 1 O1 32-1 2000 Contents Page 3 Foreword 4 1 2 3 4 4.1 4.2 5 5.1 5.2 6 6.1 6.2 7 7. I 7.2 7.3 7.4 7.5 7.6 7.7 7.8 8 8.1 8.2 9 10 Scope 4 Normative references 5 Terms and definitions 6 6 6 Classification and designa

15、tion Classification Designation 6 6 7 Information to be supplied by the purchaser Mandatory information Options 8 8 8 Manufacturing process General Deoxidation 8 8 8 8 8 8 9 9 9 Requirements General Method of delivery Delivery condition Chemical composition Mechanical properties Structure Surface fi

16、nish Dimensions and tolerances on dimensions and shape 9 9 10 Inspection General Specific inspection and testing 10 Sampling IO 10 10 10 Test methods I O. 1 Chemical analysis 10.2 Tensile test 10.3 Hardness test I1 I I Labelling, packaging and protection I1 12 Retests 12 Annex A (normative): Supplem

17、entary or special requirements 13 Bibliography OBSI 05-2000 COPYRIGHT European Committee for StandardizationLicensed by Information Handling ServicesSTD-BSI BS EN LOL32-L-ENGL 2000 Lb24669 0851147 633 H Page 3 EN 10132-1 12000 Foreword This European Standard has been prepared by Technical Committee

18、ECISSTTC 23, Steels for heat treatment, alloy steels and free-cutting steels - Qualities and dimensions, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by Au

19、gust 2000, and conflicting national standards shall be withdrawn at the latest by August 2000. This European Standard has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association. This European Standard is considered to be a supporting standard to

20、 those application and product standards which in themselves support an essential safety requirement of a New Approach Directive and which make reference to this European Standard. According to the CENKENELEC Internai Regulations, the national standards organizations of the following countries are b

21、ound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. The European Standard EN 1 O1 32, Cold rolled narrow steel str

22、ip for heat-treatment - Technical delivery conditions, is subdivided as follows: Part I : General; Part 2: Case hardening steels; Part 3: Steels for quenching and tempering; Part 4: Spring steels and other special applications. OBSI 05-2000 COPYRIGHT European Committee for StandardizationLicensed by

23、 Information Handling Services STD=BSI BS EN lOL32-L-ENGL 2000 - Lb24bb9 085Ll48 57T Page 4 EN 1 O1 32-1 12000 1 Scope I .I This part of EN I O1 32 specifies the general technical delivery conditions for non-alloy and alloy cold rolled narrow steel strip in rolling widths c 600 mm for heat treatment

24、. 1.2 In special cases supplementary requirements or deviations with respect to this European Standard may be agreed between the purchaser and the supplier at the time of enquiry and order (see annex A). 1.3 In addition to the requirements of this standard, the general technical delivery requirement

25、s specified in EN 10021 apply. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, sub

26、sequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. CR 10260, Designation systems for steel - Additional symbols. CR 10

27、261, Iron and steel - Review of available methods of chemical analysis. EN 10002-1, Metallic materials - Tensile testing - Part 7: Method of test (at ambient temperature). EN 10020, Definition and classification of grades of steel. EN 1 002 1 , General technical delivery requirements for steel and i

28、ron products EN 10027-1, Designation systems for steel - Part 7: Steel names, principal symbols. EN 10027-2, Designation systems for steel - Part 2: Numerical system. EN 10052, Vocabulary of heat treatment terms for ferrous products. EN 10079, Definition of steel products. EN IS0 6508-1, Metallic ma

29、teials - Rockwell hardness test - Part I: Test method (scales A, 6, C, D, E, F, G, H, K, N, T) (IS0 6508-1:1999). EN 1 O1 32-2, Cold rolled narrow steel strip - Technical delivery conditions - Part 2: Case hardening steels. EN 1 O1 32-3, Cold rolled narrow steel strip - Technical delivery conditions

30、 - Part 3: Steel for quenching and tempering. QBSI 05-2000 - COPYRIGHT European Committee for StandardizationLicensed by Information Handling Services STD.BSI BS EN LO332-3-ENGL 2000 m Lb24bb 0853349 406 Page 5 EN 101 32-1 12000 EN 1 O1 32-4, Cold rolled narrow steel strip - Technical delivery condi

31、tions - Patt 4: Spring steels and other special applications. EN 1 O1 40, Cold rolled narrow steel strip - Tolerances on dimensions and shape. EN 10204, Metallic products - Types of inspection documents (includes amendment A1:7995). EN IS0 377, Steel and steel products - Location and preparation of

32、samples and test pieces for mechanical testing (IS0 377: 1997). EN IS0 6507-1 , Metallic materials - Vickers hardness test - Part I: Test method (IS0 6507-717997). EURONORM 103), Microscopic determination of the ferritic or austenitic grain size of steels. IS0 14284, Steel and iron - Sampling and pr

33、eparation of samples for the determination of chemical composition. 3 Terms and definitions For the purposes of this standard the following term and definition apply in addition to the terms and definitions in EN 10020, EN 10021, EN 10052, EN 10079, EN IS0 377 and IS0 14284: 3.1 production lot produ

34、cts from the same cast, with the same thickness and the same heat-treatment cycle ) It may be agreed at the time of ordering, until this EURONORM has been adopted as a European Standard, that either this EURONORM or a corresponding national standard should be applied. OBSI 05-2000 COPYRIGHT European

35、 Committee for StandardizationLicensed by Information Handling ServicesPage 6 EN I O1 32-1 2000 4 Classification and designation 4.1 Classification The classification of the relevant steel grades according to EN 10020 is indicated in EN 10132-2, EN 10132-3 and EN 10132-4. 4.2 Designation 4.2.1 Steel

36、 names For the steel grades covered by this European Standard, the steel names as given in the relevant tables of EN 10132-2, EN 10132-3 and EN 10132-4 are allocated in accordance with EN 10027-1 and CR 10260. 4.2.2 Steel numbers For the steel grades covered by this European Standard, the steel numb

37、ers as given in the relevant tables of EN 10132-2, EN 10132-3 and EN 10132-4 are allocated in accordance with EN 10027-2. 5 Information to be supplied by the purchaser 5.1 Mandatory information The following information shall be supplied by the purchuser at the time of enquiry and order to enable th

38、e supplier to comply with the requirements of this European Standard: a) the quantity to be delivered; b) the designation of the product form (cold rolled narrow strip); c) the number of the dimensional standard (EN 10140); d) the dimensions and tolerances on dimensions and shape and, if applicable,

39、 letters denoting relevant special tolerances; e) the number of this European Standard including the number of the relevant part; 9 steel name or steel number (see 4.2); g) the delivery condition (see 7.3); h) if required, the type of inspection document in accordance with EN 10204. QBSI 05-2000 COP

40、YRIGHT European Committee for StandardizationLicensed by Information Handling ServicesSTD.BS1 BS EN LOL32-1-ENGL 2000 Lb24667 0853353 Ob4 = Page 7 EN 10132-1 12000 EXAMPLE 5 tons of cold rolled narrow strip EN 10140 - l,50x200GK EN 10132-2 - 16MnCr5+A EN 10204 - 2.2 or 5 tons of cold rolled narrow s

41、trip EN 10140 - l,50x200GK EN 10132-2 - 1.7131+A EN 10204 - 2.2 5.2 Options A number of options are specified in this European Standard and listed below. If the purchaser does not indicate his wish to implement one of these options, the supplier shall act in accordance with the basic specification o

42、f this European Standard (see 5.1): a) any requirement on surface condition; b) any requirement concerning type of edges; c) any special requirement concerning bend test (see 7.5); d) any special requirement relating to grain size (see 7.6.1 and A.2); e) any requirement concerning non-metallic inclu

43、sions (see 7.6.2 and A.3); 9 any requirement concerning surface roughness (see 7.7); g) any requirement on labelling (see clause 11); h) any special requirement on marking (see clause 11); i) any requirement on dimensions and weight of coils (see clause 1 I); j) any requirement on the method of pack

44、aging (see clause 11); k) any requirement concerning protection during transport and handling (see clause 11); I) any requirement concerning bar coding (see clause 11); m) any verification of the product analysis (see A. 1 ). QBSI 05-2000 COPYRIGHT European Committee for StandardizationLicensed by I

45、nformation Handling ServicesSTD.BS1 BS EN 1OL32-1-ENGL 2000 = 1624bb9 0851152 TTO Page 8 EN 1 O1 32-1 :2000 6 Manufacturing process 6.1 General The manufacturing process of the steel and of the products is left to the discretion of the manufacturer and subject to restrictions given by the requiremen

46、ts in 6.2. 6.2 Deoxidation All steels shall be killed. 7 Requirements 7.1 General The manufacturer is responsible, using the means he thinks fit, for controlling his production from the point of view of the various quality criteria specified. 7.2 Method of delivery The products shall be delivered by

47、 cast or part of a cast. The number of casts per delivery shall be minimized as far as it is possible. 7.3 Delivery condition The products shall be supplied as agreed at the time of enquiry and order in one of the delivery conditions indicated in EN 10132-2, EN 10132-3 and EN 10132-4. 7.4 Chemical c

48、omposition 7.4.1 Cast analysis The chemical composition of the steel as shown by the cast analysis shall conform with the values specified in the relevant tables of EN 1 O1 32-2, EN 1 O1 32-3 and EN 1 O1 32-4. 7.4.2 Product analysis The permissible deviations in the product analysis in relation to t

49、he specified limits of cast analysis (see 7.4.1) are indicated in the relevant tables of EN 1 O1 32-2, EN 1 O1 32-3 and EN 1 O1 32-4. 7.5 Mechanical properties The mechanical properties of the products shall meet the values stated in the relevant tables of EN 10132-2, EN 10132-3 and EN 101324. OBSI 05-2000 COPYRIGHT European Committee for StandardizationLicensed by Information Handling ServicesSTD=BSI BS EN LOL32-L-ENGL 2000 = Lb24bb7 085LL53 737 Page 9 EN 10132-1:2000 7.6 Structure 7.6.1 Grain size Unless otherwise agreed at the time of ordering, the grain size shal