EN 1013-2012 en Light transmitting single skin profiled plastics sheets for internal and external roofs walls and ceilings - Requirements and test methods (Incorporates Amendment A.pdf

《EN 1013-2012 en Light transmitting single skin profiled plastics sheets for internal and external roofs walls and ceilings - Requirements and test methods (Incorporates Amendment A.pdf》由会员分享，可在线阅读，更多相关《EN 1013-2012 en Light transmitting single skin profiled plastics sheets for internal and external roofs walls and ceilings - Requirements and test methods (Incorporates Amendment A.pdf（62页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationLight transmitting single skin profiled plastic sheets for internal and external roofs, walls and ceilings Requirements and test methodsBS EN 1013:2012+A1:2014BS EN 1013:2012+A1:2014National forewordThis British Standard is the UK implementation of EN 1013:2012+A1:2014. It s

2、upersedes BS EN 1013:2012, which is withdrawn.The start and finish of text introduced or altered by amendment is indicated in the text by tags. Tags indicating changes to CEN text carry the number of the CEN amendment. For example, text altered by CEN amendment A1 is indicated by !“.The UK participa

3、tion in its preparation was entrusted by Technical Committee B/542, Roofing and cladding products for discontinuous laying, to Subcommittee B/542/1, Slating and tiling.A list of organizations represented on this subcommittee can be obtained on request to its secretary.The National Annex (informative

4、) attached to this standard provides additional guidance on the application of EN 1013.This publication does not purport to include all the necessary provisions ofa contract. Users are responsible for its correct application. The British Standards Institution 2015. Published by BSI StandardsLimited

5、2015ISBN 978 0 580 84797 4ICS 83.140.10; 91.060.01Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 May 2013.Amendments/corrigenda issued since publicationDate T

6、ext affected31 January 2015 Implementation of CEN amendment A1:2014BRITISH STANDARDEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1013:2012+A1 December 2014 ICS 83.140.10; 91.060.01 Supersedes EN 1013:2012English Version Light transmitting single skin profiled plastics sheets for internal and

7、external roofs, walls and ceilings - Requirements and test methods Plaques dclairement profiles, simple paroi, en matire plastique, pour toitures, bardages et plafonds intrieurs et extrieurs - Exigences et mthodes dessai Lichtdurchlssige, einschalige profilierte Platten aus Kunststoff fr Innen- und

8、Auenanwendungen an Dchern, Wnden und Decken - Anforderungen und Prfverfahren This European Standard was approved by CEN on 20 October 2012 and includes Amendment 1 approved by CEN on 22 August 2014. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditi

9、ons for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists i

10、n three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standar

11、ds bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slove

12、nia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2014 CEN All rights of exploitation in any form and by any means reserved

13、worldwide for CEN national Members. Ref. No. EN 1013:2012+A1:2014 E2 Contents Page Foreword 4 Introduction .5 1 Scope 6 2 Normative references 6 3 Terms and definitions .7 4 Symbols and abbreviations 8 4.1 Symbols 8 4.2 Abbreviations .8 5 Requirements .8 5.1 Visual appearance .8 5.2 Dimensional tole

14、rances and mass per square metre 8 5.3 Light transmission .9 5.4 Flexural/tensile strength .9 5.5 Durability . 10 5.6 Thermal ageing resistance (only for thermoplastic sheets) 12 5.7 Longitudinal reversion and profile retention (only for thermoplastic sheets) . 12 5.8 Impact resistance 12 5.9 Resist

15、ance to deflection (mechanical resistance) 12 5.10 Water vapour permeability . 13 5.11 Water/air permeability 13 5.12 Linear thermal expansion 13 5.13 Reaction to fire 14 5.14 External fire performance 14 5.15 Glass-fibre content (only for glass-fibre reinforced sheets) 15 5.16 Barcol hardness (only

16、 for glass-fibre reinforced sheets) 15 5.17 Presence of protective coating . 15 5.18 Adhesion of surface coating (only for glass-fibre reinforced sheets) 16 5.19 Resistance to fixings 16 5.20 Dangerous substances 16 6 Test methods . 16 6.1 Dimensional tolerances . 16 6.2 Light transmission 20 6.3 Ye

17、llowness index 20 6.4 Flexural/tensile strength 21 6.5 Thermal ageing resistance 21 6.6 Longitudinal reversion and profile retention . 22 6.7 Small hard body impact resistance 24 6.8 Resistance to deflection 26 6.9 Reaction to fire 29 6.10 External fire performance 31 6.11 Glass-fibre content . 32 6

18、.12 Barcol hardness 32 6.13 Presence of protective coating . 32 6.14 Adhesion of surface coating . 35 7 Assessment and verification of constancy of performance AVCP 36 7.1 General . 36 7.2 Product type determination . 36 BS EN 1013:2012+A1:2014 EN 1013:2012+A1:2014 (E)3 7.3 Factory production contro

19、l (FPC) 38 7.4 Initial inspection of factory and of FPC . 40 7.5 Continuous surveillance of FPC 40 8 Marking and labelling 41 Annex A (normative) Profile terminology . 42 Annex B (normative) Glass content by density of laminate . 45 Annex ZA (informative) Clauses of this European Standard addressing

20、 the provisions of the EU Construction Products Regulation 47 Bibliography 58 BS EN 1013:2012+A1:2014 EN 1013:2012+A1:2014 (E)4 Foreword This document (EN 1013:2012+A1:2014) has been prepared by Technical Committee CEN/TC 128 “Roof covering products for discontinuous laying and products for wall cla

21、dding”, the secretariat of which is held by NBN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2015, and conflicting national standards shall be withdrawn at the latest by September 2016. A

22、ttention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes !EN 1013:2012“. This document includes Amendment 1 approved by

23、 CEN on 2014-08-22. The start and finish of text introduced or altered by amendment is indicated in the text by tags !“. !This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of the EU Con

24、struction Products Regulation. For relationship with EU Directive(s) and the Construction Products Regulation, see informative Annex ZA, which is an integral part of this document.“ !deleted text“ According to the CEN/CENELEC Internal Regulations, the national standards organizations of the followin

25、g countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norw

26、ay, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 1013:2012+A1:2014 EN 1013:2012+A1:2014 (E)5 Introduction This document describes the requirements and test methods for light transmitting single skin profiled plastics sheets. The phys

27、ical properties of light transmitting single skin profiled plastics sheets differ from bituminous, metal and fibre reinforced cement sheets, as defined in EN 534 1, EN 506 2, EN 508-1 3, EN 508-2 4, EN 508-3 5 and EN 494 6. They do not necessarily have the same span capabilities and alternative fixi

28、ng specifications are generally required. Reference should be made to national regulations and the manufacturers literature for requirements concerning design, storage and installation, including all safety aspects, according to the material. BS EN 1013:2012+A1:2014 EN 1013:2012+A1:2014 (E)6 1 Scope

29、 This European Standard specifies the requirements for light transmitting single skin profiled plastics sheets for internal and external walls, roofs and ceilings. It is applicable to single skin sheets which are used as a single layer or when assembled to form a multiple layer construction. It also

30、 specifies the test methods and provides for the evaluation of conformity and marking of the sheets. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cite

31、d applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 59, Glass reinforced plastics - Measurement of hardness by means of a Barcol impressor CEN/TS 1187:2012, Test methods for external fire exposure to roofs EN 13501-1, Fire classific

32、ation of construction products and building elements Part 1: Classification using data from reaction to fire tests EN 13501-5, Fire classification of construction products and building elements Part 5: Classification using data from external fire exposure to roofs tests EN 13823:2010, Reaction to fi

33、re tests for building products - Building products excluding floorings exposed to the thermal attack by a single burning item EN ISO 178, Plastics Determination of flexural properties (ISO 178) EN ISO 472:2001, Plastics Vocabulary (ISO 472:1999) EN ISO 527-1, Plastics Determination of tensile proper

34、ties Part 1: General principles (ISO 527-1) EN ISO 527-2, Plastics Determination of tensile properties Part 2: Test conditions for moulding and extrusion plastics (ISO 527-2) EN ISO 527-4, Plastics Determination of tensile properties Part 4: Test conditions for isotropic and orthotropic fibre-reinfo

35、rced plastic composites (ISO 527-4) EN ISO 1043-1:2011, Plastics - Symbols and abbreviated terms - Part 1: Basic polymers and their special characteristics (ISO 1043-1:2011) EN ISO 1043-2:2011, Plastics - Symbols and abbreviated terms - Part 2: Fillers and reinforcing materials (ISO 1043-2:2011) EN

36、ISO 1172:1998, Textile-glass-reinforced plastics - Prepregs, moulding compounds and laminates - Determination of the textile-glass and mineral-filler content - Calcination methods (ISO 1172:1996) EN ISO 4892-2:2006, Plastics Methods of exposure to laboratory light sources Part 2: Xenon-arc lamps (IS

37、O 4892-2:2006) EN ISO 4892-3:2006, Plastics Methods of exposure to laboratory light sources Part 3: Fluorescent UV lamps (ISO 4892-3:2006) EN ISO 6603-1, Plastics Determination of puncture impact behaviour of rigid plastics Part 1: Non-instrumented impact testing (ISO 6603-1) BS EN 1013:2012+A1:2014

38、 EN 1013:2012+A1:2014 (E)7 !Deleted text“ EN ISO 11664-1, Colorimetry Part 1: CIE standard colorimetric observers (ISO 11664-1) EN ISO 11664-2:2011, Colorimetry - Part 2: CIE standard illuminants (ISO 11664-2:2007) EN ISO 11925-2:2010, Reaction to fire tests - Ignitability of products subjected to d

39、irect impingement of flame - Part 2: Single-flame source test (ISO 11925-2:2010) EN ISO 12572, Hygrothermal performance of building materials and products Determination of water vapour transmission properties (ISO 12572) EN ISO 13468-1, Plastics Determination of the total luminous transmittance of t

40、ransparent materials Part 1: Single-beam instrument (ISO 13468-1) EN ISO 13468-2, Plastics Determination of the total luminous transmittance of transparent materials Part 2: Double-beam instrument (ISO 13468-2) EN ISO 14125, Fibre-reinforced plastic composites Determination of flexural properties (I

41、SO 14125) ISO 11359-2, Plastics Thermomechanical analysis (TMA) Part 2: Determination of coefficient of linear thermal expansion and glass transition temperature ETAG 010, Self supporting translucent roof kits 3 Terms and definitions For the purposes of this document, the terms and definitions given

42、 in EN ISO 472:2001, EN ISO 1043-1:2011, EN ISO 1043-2:2011 and Annex A and the following apply. 3.1 indirect test (IT) test performed by the manufacturer, different from that specified for that particular characteristic, having verified its correlation with the specified test 3.2 yellowness deviati

43、on in chroma from whiteness or water-whiteness in the dominant wavelength range from 570 nm to 580 nm 3.3 yellowness index magnitude in yellowness relative to CIE standard illuminant D 65 3.4 radiant exposure H time integral of irradiance, measured in joules per square metre (J m-2) SOURCE: ISO 9370

44、:1997 7 BS EN 1013:2012+A1:2014 EN 1013:2012+A1:2014 (E)8 4 Symbols and abbreviations 4.1 Symbols Anclass for the exposure to artificial accelerated weathering using xenon-arc lamps Bnclass for the exposure to artificial accelerated weathering using fluorescent UV lamps H radiant exposure YI yellown

45、ess index of a test specimen exposed to ageing YI0yellowness index of a test specimen unexposed to ageing YI change of the yellowness index after ageing 4.2 Abbreviations FPC factory production control GRA glass-fibre reinforced acrylic (PMMA) GRP glass-fibre reinforced polyester ITT initial type te

46、sting PC polycarbonate PET poly(ethylene terephthalate) PMMA poly(methyl methacrylate) PVC-U unplasticised poly(vinyl chloride) PVF poly(vinyl fluoride) 5 Requirements 5.1 Visual appearance Both sides of the sheets shall be of regular appearance. Visual or tactile examination shall reveal no evidenc

47、e of any hole, cracking or splitting, and no cluster of bubbles greater than 1 mm in diameter, or inclusions that are likely to affect properties. For GRP sheets, any defects such as resin ribs, glass folds or glass knots shall not exceed 5 mm in diameter. The edges of the sheet shall be straight an

48、d clean. Further requirements concerning the visual aspects of the sheets can be agreed upon between the manufacturer and the customer. Where required, the sheet shall be declared as “diffusing” or “non-diffusing” depending on whether the image of an object placed 1 m behind the sheet appears blurre

49、d or sharp, respectively. 5.2 Dimensional tolerances and mass per square metre The dimensional tolerances and mass per square metre shall be assessed when subject to regulatory requirement. When measured in accordance with the test methods as specified in 6.1.1 to 6.1.3 and Table 1, the dimensional tolerances and mass per square metre of the sheets shall conform to the requirements given in Table 1. BS EN 1013:2012+A1:2014 EN 1013:2012+A1:2014 (E)9 The test methods given in Table 1 are used for ini