EN 10028-5-2017 en Flat products made of steels for pressure purposes - Part 5 Weldable fine grain steels thermomechanically rolled.pdf

《EN 10028-5-2017 en Flat products made of steels for pressure purposes - Part 5 Weldable fine grain steels thermomechanically rolled.pdf》由会员分享，可在线阅读，更多相关《EN 10028-5-2017 en Flat products made of steels for pressure purposes - Part 5 Weldable fine grain steels thermomechanically rolled.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、Flat products made of steels for pressure purposesPart 5: Weldable fine grain steels, thermomechanically rolledBS EN 100285:2017BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 10028-5 July 2017 ICS 77.140.30; 77.14

2、0.50 Supersedes EN 10028-5:2009English Version Flat products made of steels for pressure purposes - Part 5: Weldable fine grain steels, thermomechanically rolled Produits plats en acier pour appareils pression - Partie 5 : Aciers soudable grains fins, lamins thermomcaniquement Flacherzeugnisse aus D

3、ruckbehltersthlen - Teil 5: Schweigeeignete Feinkornbausthle, thermomechanisch gewalzt This European Standard was approved by CEN on 7 May 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a

4、national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A

5、 version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cypr

6、us, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and Un

7、ited Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. E

8、N 10028-5:2017 ENational forewordThis British Standard is the UK implementation of EN 100285:2017. It supersedes BS EN 100285:2009, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee ISE/107, Steels for Pressure Purposes.A list of organizations represente

9、d on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2017 Published by BSI Standards Limited 2017ISBN 978 0 580 878

10、49 7ICS 77.140.30; 77.140.50Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 August 2017.Amendments/corrigenda issued since publicationDate Text affectedBRITIS

11、H STANDARDBS EN 100285:2017EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 10028-5 July 2017 ICS 77.140.30; 77.140.50 Supersedes EN 10028-5:2009English Version Flat products made of steels for pressure purposes - Part 5: Weldable fine grain steels, thermomechanically rolled Produits plats en ac

12、ier pour appareils pression - Partie 5 : Aciers soudable grains fins, lamins thermomcaniquement Flacherzeugnisse aus Druckbehltersthlen - Teil 5: Schweigeeignete Feinkornbausthle, thermomechanisch gewalzt This European Standard was approved by CEN on 7 May 2017. CEN members are bound to comply with

13、the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Managem

14、ent Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same statu

15、s as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,

16、 Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 20

17、17 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 10028-5:2017 EBS EN 100285:2017EN 10028-5:2017 (E) 2 Contents Page European foreword 3 1 Scope 4 2 Normative references 4 3 Terms and definitions . 4 4 Tolerances on dimensions . 4

18、 5 Calculation of mass . 4 6 Classification and designation . 5 6.1 Classification . 5 6.2 Designation . 5 7 Information to be supplied by the purchaser . 5 7.1 Mandatory information 5 7.2 Options 5 7.3 Example for ordering. 5 8 Requirements . 6 8.1 Steelmaking process 6 8.2 Delivery condition 6 8.3

19、 Chemical composition . 6 8.4 Mechanical properties 6 8.5 Surface condition 6 8.6 Internal soundness . 6 9 Inspection 6 9.1 Types of inspection and inspection documents . 6 9.2 Tests to be carried out 6 9.3 Retests, sorting and reprocessing . 6 10 Sampling . 7 11 Test methods 7 12 Marking 7 Annex A

20、(informative) Information on weldability . 11 Annex B (informative) Changes to the previous version EN 10028-5:2009 . 12 Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of Directive 2014/68/EU 13 BS EN 100285:2017EN 10028-5:2017 (E) 3 European forewo

21、rd This document (EN 10028-5:2017) has been prepared by Technical Committee ECISS/TC 107 “Steels for pressure purposes”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at

22、the latest by January 2018 and conflicting national standards shall be withdrawn at the latest by January 2018. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any o

23、r all such patent rights. This document supersedes EN 10028-5:2009. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of Directive 2014/68/EU. For relationship with Directive 2014/68/EU

24、, see informative Annex ZA, which is an integral part of this document. A list of changes between this document and the previous version can be found in Annex B. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement

25、this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serb

26、ia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 100285:2017EN 10028-5:2017 (E) 4 1 Scope This European Standard specifies the requirements for flat products for pressure equipment made of weldable fine grain thermomechanically rolled steels as specified in Ta

27、ble 1. The steels are not suitable for hot forming. NOTE 1 At the time of publication of this European Standard, no sufficient data for the standardization of the elevated temperature properties of these steels was available. If their use at such temperatures is intended the conditions for this shou

28、ld be specially agreed between the interested parties. The requirements of EN 10028-1:2017 also apply. NOTE 2 Once this European Standard is published in the EU Official Journal (OJEU) under Directive 2014/68/EU, presumption of conformity to the Essential Safety Requirements (ESRs) of Directive 2014

29、/68/EU is limited to technical data of materials in this European Standard (Part 1 and the other relevant part of the series) and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the

30、 design requirements of this specific item of equipment to verify that the ESRs of Directive 2014/68/EU are satisfied, needs to be done. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dat

31、ed references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1011-1:2009, Welding Recommendations for welding of metallic materials Part 1: General guidance for arc welding EN 1011-2:2001, Welding Recommen

32、dations for welding of metallic materials Part 2: Arc welding of ferritic steels EN 10020:2000, Definition and classification of grades of steel EN 10028-1:2017, Flat products made of steels for pressure purposes Part 1: General requirements EN 10204:2004, Metallic products Types of inspection docum

33、ents 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 10028-1:2017 apply. 4 Tolerances on dimensions See EN 10028-1:2017. 5 Calculation of mass See EN 10028-1:2017. BS EN 100285:2017EN 10028-5:2017 (E) 5 6 Classification and designation 6.1 Classificat

34、ion 6.1.1 This European Standard covers the steel grades given in Table 1 in three qualities: a) the basic series (P.M); b) series with low temperature properties down to 40 C (P.ML1); c) series with low temperature properties down to 50 C (P.ML2). 6.1.2 In accordance with EN 10020:2000 all the stee

35、ls specified in this document are alloy special steels. 6.2 Designation See EN 10028-1:2017. 7 Information to be supplied by the purchaser 7.1 Mandatory information See EN 10028-1:2017. 7.2 Options A number of options are specified in this document and listed below. Additionally the relevant options

36、 of EN 10028-1:2017 apply. If the purchaser does not indicate a wish to implement any of these options at the time of enquiry and order, the products shall be supplied in accordance with the basic specification (see also EN 10028-1:2017): 1) providing data on suitable welding conditions (see 8.2.2);

37、 2) maximum carbon equivalent (see 8.3.3); 3) specification of a minimum impact energy of 40 J (see 8.4 and Table 5); 4) mid thickness test pieces for the impact test (see Clause 10). 7.3 Example for ordering 10 plates with nominal dimensions, thickness = 50 mm, width = 2 000 mm, length = 10 000 mm,

38、 made of a steel grade with the name P355ML2 and the number 1.8833 as specified in EN 10028-5, inspection certificate 3.1 as specified in EN 10204: 10 plates 50 2 000 10 000 EN 10028-5 P355ML2 Inspection certificate 3.1 or 10 plates 50 2 000 10 000 EN 10028-5 1.8833 Inspection certificate 3.1 BS EN

39、100285:2017EN 10028-5:2017 (E) 6 8 Requirements 8.1 Steelmaking process See EN 10028-1:2017. 8.2 Delivery condition 8.2.1 The products covered by this European Standard shall be supplied in the thermomechanically rolled condition. 8.2.2 Information on weldability are given in Annex A of this standar

40、d. 8.3 Chemical composition 8.3.1 The requirements of Table 1 apply for the chemical composition according to the cast analysis. 8.3.2 The product analysis shall not deviate from the specified values for the cast analysis as specified in Table 1 by more than the values given in Table 2. 8.3.3 A maxi

41、mum value for the carbon equivalent in accordance with Table 3 may be agreed at time of enquiry and order. 8.4 Mechanical properties The values given in Tables 4 and 5 (see also EN 10028-1:2017 and Clause 10) shall apply. Optionally, a minimum impact energy value of 40 J may be specified for tempera

42、tures where lower minimum values are specified (see Table 5, footnote a). 8.5 Surface condition See EN 10028-1:2017. 8.6 Internal soundness See EN 10028-1:2017. 9 Inspection 9.1 Types of inspection and inspection documents See EN 10028-1:2017. 9.2 Tests to be carried out See EN 10028-1:2017. 9.3 Ret

43、ests, sorting and reprocessing See EN 10028-1:2017. BS EN 100285:2017EN 10028-5:2017 (E) 7 10 Sampling See EN 10028-1:2017. For the impact test, deviating from EN 10028-1:2017, Table 4, footnote g, the preparation of test pieces taken from the mid thickness may be agreed at the time of enquiry and o

44、rder. In this case, test temperatures and minimum impact energy values shall also be agreed. 11 Test methods See EN 10028-1:2017. 12 Marking See EN 10028-1:2017. BS EN 100285:2017EN10028-5:2017(E)8Table1Chemicalcomposition(castanalysis)aSteelgradeContent, %bymassSteelnameSteelnumberCmax.Simax.Mnbmax

45、.Pmax.Smax.Altotalcmin.Nmax.Moemax.Nbfmax.Nimax.TifmaxVfmax.OtherP355M1.88210,140,501,600,0250,0100,020d0,0150,200,05g0,500,050,10eP355ML11.88320,0200,008P355ML21.88330,005P420M1.88240,160,501,700,0250,0100,020P420ML11.88350,0200,008P420ML21.88280,005P460M1.88260,160,601,700,0250,010P460ML11.88370,0

46、200,008P460ML21.88310,005aElementsnot listed inthistableshallnot beintentionallyadded to thesteelwithout theagreement ofthepurchaserexcept forfinishingthe cast.All appropriatemeasuresshallbetakento prevent theadditionfrom scrapand othermaterialsused insteelmakingoftheseelementswhichmayadverselyaffec

47、t themechanicalpropertiesand usability.bForeachreductionof0,02%belowthemaximum carboncontent,anincreaseof0,05%Mnabovethespecified maximum valueispermitted,upto amaximumof2,00%Mn.cThe Alcontentofthecast shallbedetermined and givenintheinspectiondocument.dTheminimumvalueforAltotaldoesnotapplyifadequat

48、econtentsofothernitrogen-fixingelementsarepresent.e(Cr+Cu+Mo)0,60%.fThetotal ofV+Nb+Tishall not exceed avalueof0,15%.gIfthecarboncontent isrestricted to0,07%,amaximum niobium content of0,10%ispermitted.Inthiscase,special careshall betakentoavoidproblemsintheheataffected zoneat operationtemperatureso

49、f40CandbeloworafterPWHT.BS EN 100285:2017EN10028-5:2017(E)8Table1Chemicalcomposition(castanalysis)aSteelgradeContent, %bymassSteelnameSteelnumberCmax.Simax.Mnbmax.Pmax.Smax.Altotalcmin.Nmax.Moemax.Nbfmax.Nimax.TifmaxVfmax.OtherP355M1.88210,140,501,600,0250,0100,020d0,0150,200,05g0,500,050,10eP355ML11.88320,0200,008P355ML21.88330,005P420M1.88240,160,501,700,0250,0100,020P420ML11.88350,0200,008P420ML21.88280,005P460M1.88260,160,601,700,0250,010P460ML11.88370,0200,008P460ML21.88310,005aElementsnot