ECA EIA-62391-2-2014 Fixed Electric Double-Layer Capacitors for Use in Electronic Equipment C Part 2 Sectional Specification C Electric Double- Layer Capacitors for Power Applicati.pdf

《ECA EIA-62391-2-2014 Fixed Electric Double-Layer Capacitors for Use in Electronic Equipment C Part 2 Sectional Specification C Electric Double- Layer Capacitors for Power Applicati.pdf》由会员分享，可在线阅读，更多相关《ECA EIA-62391-2-2014 Fixed Electric Double-Layer Capacitors for Use in Electronic Equipment C Part 2 Sectional Specification C Electric Double- Layer Capacitors for Power Applicati.pdf（27页珍藏版）》请在麦多课文档分享上搜索。

1、 EIA STANDARD Fixed Electric Double-Layer Capacitors for Use in Electronic Equipment Part 2: Sectional Specification Electric Double- Layer Capacitors for Power Application EIA-62391-2 (IEC 62391-2:2006, IDT) October 2014 ANSI/EIA-62391-2-2014 Approved: October 6, 2014 EIA-60384-11 EIA-62391-2NOTICE

2、 EIA Engineering Standards and Publications are designed to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the

3、 proper product for his particular need. Existence of such Standards and Publications shall not in any respect preclude any member or nonmember of ECIA from manufacturing or selling products not conforming to such Standards and Publications, nor shall the existence of such Standards and Publications

4、 preclude their voluntary use by those other than ECIA members, whether the standard is to be used either domestically or internationally. Standards and Publications are adopted by ECIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, ECIA does not a

5、ssume any liability to any patent owner, nor does it assume any obligation whatever to parties adopting the Standard or Publication. This EIA Standard is identical (IDT) with the International Standard IEC Publication 62391-2:2006: Fixed Electric Double-Layer Capacitors for Use in Electronic Equipme

6、nt Part 2: Sectional Specification Electric Double-Layer Capacitors for Power Application. This document is the EIA Standard EIA-62391-2: 2014: Fixed Electric Double-Layer Capacitors for Use in Electronic Equipment Part 2: Sectional Specification Electric Double- Layer Capacitors for Power Applicati

7、on. The text, figures and tables of IEC 62391-2:2006 are used in this Standard with the consent of the IEC and the American National Standards Institute (ANSI). The IEC copyrighted material has been reproduced with permission from ANSI. The IEC Foreword and Introduction are not part of the requireme

8、nts of this standard but are included for information purposes only. This Standard does not purport to address all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and health pract

9、ices and to determine the applicability of regulatory limitations before its use. (From Standards Proposal No. 5297, formulated under the cognizance of the Steering Committee for Passive Electronic Components Standards (S-1). Published by Electronic Components Industry Association 2014 Standards any

10、 IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardi

11、zation (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has repres

12、entation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC

13、cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publica

14、tions. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with an I

15、EC Publication. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal inju

16、ry, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references c

17、ited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identif

18、ying any or all such patent rights. International Standard IEC 62391-2 has been prepared by IEC technical committee 40: Capacitors and resistors for electronic equipment. This bilingual version corresponds to the monolingual English version, published in 2006-04. The text of this standard is based o

19、n the following documents: FDIS Report on voting 40/1641/FDIS 40/1713/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. The French version of this standard has not been voted upon. This publication has been drafted

20、 in accordance with the ISO/IEC Directives, Part 2. EIA-62391-2 Page 2 IEC 62391 consists of the following parts, under the general title Fixed electric double-layer capacitors for use in electronic equipment: Part 1: Generic specification Part 2: Sectional specification Electric double-layer capaci

21、tors for power application The sectional specification mentioned above does have a blank detail specification being a supplementary document, containing requirements for style, layout and minimum content of detail specifications. The committee has decided that the contents of this publication will r

22、emain unchanged until the maintenance result date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed; withdrawn; replaced by a revised edition, or amended. EIA-62391-2 Page 3 FIXED ELECTRIC DO

23、UBLE-LAYER CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT Part 2: Sectional specification Electric double-layer capacitors for power application 1 General 1.1 Scope This part of IEC 62391 applies to electric double-layer capacitors for power application. Electric double-layer capacitors for power are in

24、tended for applications that require discharge currents in the range from mA to A. The characteristics of the capacitors include such performance as relatively high capacitance and low internal resistance, which is applicable to Class 3 of the measurement classification specified in IEC 62391-1. The

25、 definition of power density and its calculating procedure should be in accordance with Annex A. 1.2 Object The object of this standard is to prescribe preferred ratings and characteristics and to select from IEC 62391-1 the appropriate quality assessment procedures, tests and measuring methods and

26、to give general performance requirements for this type of capacitor. Test severities and requirements prescribed in detail specifications referring to this sectional specification shall be of equal or higher performance level; lower performance levels are not permitted. 1.3 Normative references The

27、following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60063, Preferred number series for resistors and

28、capacitors IEC 60068-1, Environmental testing Part 1: General and guidance IEC 60384-1, Fixed capacitors for use in electronic equipment Part 1: Generic specification IEC 60410, Sampling plans and procedures for inspection by attributes IEC 62391-1, Fixed electric double-layer capacitors for use in

29、electronic equipment Part 1: Generic specification IEC 62391-2-1, Fixed electric double-layer capacitors for use in electronic equipment Part 2-1: Electric double-layer capacitors for power application Assessment level EZ ISO 3, Preferred numbers Series of preferred numbers EIA-62391-2 Page 4 1.4 In

30、formation to be given in a detail specification Detail specifications shall be derived from the relevant blank detail specification. Detail specifications shall not specify requirements inferior to those of the generic, sectional or blank detail specification. When more severe requirements are inclu

31、ded, they shall be listed in 1.9 of the detail specification and indicated in the test schedules, for example by an asterisk. NOTE The information given in 1.4.1 may, for convenience, be presented in tabular form. The following information shall be given in each detail specification and the values q

32、uoted shall preferably be selected from those given in the appropriate clause of this sectional specification. 1.4.1 Outline drawing and dimensions There shall be an illustration of the surface mount capacitors as an aid to easy recognition and for comparison of the surface mount capacitors with oth

33、ers. Dimensions and their associated tolerances, which affect interchangeability and mounting, shall be given in the detail specification. All dimensions shall preferably be stated in millimetres; however, when the original dimensions are given in inches, the converted metric dimensions in millimetr

34、es shall be added. Normally, numerical values shall be given for the length of the body, the width and height of the body and wire spacing, or, for cylindrical types, the body diameter and length, and the length and diameter of the terminations. When necessary, for example, when a number of case siz

35、es are covered by a detail specification, the dimensions and their associated tolerances shall be placed in a table below the drawing. When the configuration is other than described above, the detail specification shall state such dimensional information as will adequately describe the capacitor. Wh

36、en the capacitor is not designed for use on printed boards, this shall be clearly stated in the detail specification. 1.4.2 Mounting The detail specification shall specify the method of mounting to be applied for normal use and for the application of the vibration and the bump or shock test. The cap

37、acitors shall be mounted by their normal means. The design of the capacitor may be such that special mounting fixtures are required for its use. In this case, the detail specification shall describe the mounting fixtures and they shall be used in the application of the vibration and bump or shock te

38、sts. 1.4.3 Rating and characteristics The ratings and characteristics shall be in accordance with the relevant clauses of this specification, together with the following. 1.4.3.1 Rated capacitance range See 2.2.1. NOTE When products approved to the detail specification have different ranges, the fol

39、lowing statement should be added: “The range of capacitance values available in each voltage range is given in IEC QC 001005.” EIA-62391-2 Page 5 1.4.3.2 Particular characteristics Additional characteristics may be listed, when they are considered necessary to specify adequately the component for de

40、sign and application purposes. 1.4.3.3 Soldering The detail specification shall prescribe the test methods, severities and requirements applicable to the solderability and the resistance to soldering heat tests. 1.4.4 Marking The detail specification shall specify the content of the marking on the c

41、apacitor and on the package. Deviations from 1.6 of this sectional specification shall be specifically stated. 1.5 Terminology For the purposes of this document, the terms and definitions of IEC 62391-1, together with the following, apply. 1.5.1 surface mount capacitor capacitor whose small dimensio

42、ns and nature or shape of terminations make it suitable for surface mounting 1.5.2 electric double layer capacitors for power application capacitors intended for the applications that require discharge currents in the range from mA to A NOTE The characteristics of the capacitors include such perform

43、ance as relatively high capacitance and low internal resistance, which is applicable to Class 3 of the measurement classification specified in IEC 62391-1. 1.6 Marking IEC 62391-1, 2.4, applies with the following details. 1.6.1 The information given in the marking is normally selected from the follo

44、wing list; the relative importance of each item is indicated by its position in the list: a) polarity of the terminations (unless identified by the construction); b) rated capacitance; c) rated voltage (d.c. voltage may be indicated by the symbol or ); d) style (in accordance with 1.1); e) year and

45、month (or week) of manufacture; f) manufacturers name or trade mark; g) manufacturers type designation; h) classification of processing lead terminals (if applicable). 1.6.2 Capacitors shall bear a), b) and c) in 1.6.1, and as many of the rest of the items as possible which should be as legible as p

46、ossible. Indication of marked items on a capacitor shall not overlap. 1.6.3 Any marking shall be legible and not easily smeared or removed by rubbing with the finger. EIA-62391-2 Page 6 1.6.4 The package containing the capacitor(s) shall be clearly marked with all the information listed in 1.6.1, ex

47、cept polarity, unless this is applicable to the method of packaging. 1.6.5 Any additional marking shall be so applied that no confusion can arise. 2 Preferred rating and characteristics 2.1 Preferred characteristics The values given in the detail specification shall preferably be selected from the f

48、ollowing: 2.1.1 Preferred climatic categories The surface mount capacitors covered by this specification are classified into climatic categories according to the general rules given in IEC 60068-1. The lower and upper category temperatures and the duration of the damp-heat, steady-state test shall b

49、e chosen from the following. Lower category temperature: 25 C (40 C) Upper category temperature: +60 C and +70 C Duration of the damp-heat, steady-state test: 10 days The severities for the cold and dry heat tests are the lower and upper category temperatures respectively. NOTE The damp-heat steady-state test conditions here should be at a temperature of 40 C, and the relative humidity should be between 90 % and 95 %. 2.2 Preferred values of ratings 2.2.1 Rated capacitance (CR) The rated capacitance shall be expressed in farads (F)