DOD A-A-54675-1992 BAND AND BAND SET MATRIX DENTAL TOFFLEMIRE《结核菌素牙齿矩阵带子和带子用具》.pdf

《DOD A-A-54675-1992 BAND AND BAND SET MATRIX DENTAL TOFFLEMIRE《结核菌素牙齿矩阵带子和带子用具》.pdf》由会员分享，可在线阅读，更多相关《DOD A-A-54675-1992 BAND AND BAND SET MATRIX DENTAL TOFFLEMIRE《结核菌素牙齿矩阵带子和带子用具》.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、c T * U A-A-54b75 b5 7777774 0066770 T INCH-POUND A-A-54 6 15 19 June 1992 COMMERCIAL ITEM DESCRIPTION BAND AND BAND SET, MATRIX, DENTAL, Tofflemire The General Services Administration has authorized the use of this Commercial Item Description as a replacement for Federal Specification GG-B-95E whic

2、h is cancelled. This commercial item description covers matrix bands suitable for use for restorations in individual teeth. Salient characteristics: Classification. The matrix bands shall be of the following types and sizes, as specified: Type I. Bands, Junior size, Tofflemire Sizes Universal, No. 1

3、3 Narrow M.O.D., No. 14 Wide M.O.D., No. 15 Type II. Bands, Adult size, Tofflemire Sizes Universal, No. 1 Wide M.O.D., No. 2 Narrow M.O.D., No. 3 Window-Opening Contra Angle, No. 10 Universal Contra Angle, No. 11 Material. The matrix bands shall be fabricated from austenitic stainless steel type 301

4、, 302, or 304 in accordance with ASTM Designation F899. Hardness. The matrix bands shall have a Knoop hardness of 351 to 402, when tested as specified below, or a Rockwell hardness of C35 to C40, when tested in accordance with ASTM E18. AMSC N/A FSC 6520 DISTRIBUTION STATEMENT A. Approved for public

5、 release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-._ - - - _I_ _ - w 39 A-A-54675 65 9999974 00bb773 3 Thickness, Total Type Size (number) inches Ouantity Ouantitv I A-A-5 4 6 7 5 Unit of issue Style, desiqn and dim

6、ensions. The matrix bands shall be capable of being fitted around a tooth to supply a missing wall or contour, against which the gilling material may be placed and condensed. Bands shall be furnished in pre-stamped designs corresponding to the applicable design and size (number) specified, Junior si

7、ze bands shall be suitable for use with junior size Tofflemire retainers, and adult size bands shall be suitable for use with adult size Tofflemire retainers. All matrix bands shall conform to the design, dimensions, and size (number) shown in Defense Personnel Support Center (DPSC) Drawing No. 2335

8、5. Bands shall be furnished in the applicable size number, thickness, and quantity shown in Table I. The thickness tolerance for all bands shall be 5 0.0002 inch. 1. Junior Universal #13 0.0020 6 Size Toff- Narrow MOD #14 2 12 lemire Wide MOD #15 4 Set 12 12 12 12 12 Package Package Package Package

9、Set Window-Opening Contra-Angle, Universal Contra-Angle #i0 #i1 2. Adult Universal #1 Size Toff- Universal #l lemire Wide MOD #2 Narrow MOD #3 0.0015 0.0015 0.0015 0.0020 0.0015 0.0015 I I 12 12 12 12 4 8 Corrosion resistance. Bands shall show no signs of corrosion when subjected to the boil test in

10、 accordance with ASTM F1089. Flexibility. Bands shall withstand a minimum of two bends before breaking, when tested as specified below. A bend shall consist of one flattening followed by straightening. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-

11、,-A-A-54b75 b5 = 9999974 0066772 3 = A-A-5 4 6 7 5 Finish. The bands shall have a commercial number 2B finish or better. The bands shall be cleanly trimmed and smoothly finished. All bands shall be put through a tumbling procedure to provide smooth peripheral edges free from burrs or other imperfect

12、ions. The surface roughness of bands shall be no more than the root-mean-square average deviation of 15 . microinches when the bands are tested with a suitable surface roughness analyzer. Workmanship. The finish of the bands shall be uniform and free of burrs, sharp edges, pit marks, cracks, wrinkle

13、s, folds, tears or other imperfections. The matrix bands shall be free from any imperfections which may detract from their appearance or impair their serviceability, proper functioning, and intended use. Unit. Packaqe (PG). One package containing twelve matrix bands of one size and thickness specifi

14、ed, constitutes one unit. m. (SE). One set containing twelve junior or twelve adult matrix bands of assorted sizes, constitutes one unit. Quality Assurance Provisions. Responsibility for inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the p

15、erformance of all inspection requirements as specified herein. Except as otherwise specified in the contract r purchase order, the contractor may use his own or any facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Gove

16、rnment reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. Records. Records of examinations and tests performed by or for the contractor shall be maintained

17、 by the contractor and made available to the Government upon the Governments request, at any time, or from time to time, during the performance of the contract and for a period of three years after the delivery of the supplies to which such records relate. 3 Provided by IHSNot for ResaleNo reproduct

18、ion or networking permitted without license from IHS-,-,-A-A-54 6 75 Inspection. inspection, as used herein, is defined as both examination (such as visual or auditory investigation without the use of special laboratory appliances or procedures) and testing (determination by technical means of physi

19、cal and chemical properties) of the item. the manufacturer of the component or materials, may be furnished in lieu of actual performance of such testing by the contractor, provided lot identity has been maintained and can be demonstrated to the Government. Certificates of quality. Certificates of qu

20、ality, supplied by Samplinq for inspection. Sampling for inspection shall be conducted in accordance with MIL-STD-105. Where feasible, the same sample shall be used for the determination of two or more inspection characteristics. The unit of product for inspection purposes shall be one package or on

21、e set of matrix bands. Unless otherwise specified, sampling for examination shall be conducted at inspection level II, AQL 2.5, .except for dimensions, which shall be conducted at inspection level S-1, AQL 2.5. Sampling for tests shall be conducted at inspection level S-2 and the acceptance number s

22、hall be zero (O) for all sample sizes. Examination. The matrix bands shall be examined to determine compliance with specification requirements. Tests. Tests shall be conducted to determine compliance with specification requirements. Hardness. Knoop hardness shall be determined on a Tukon tester unde

23、r a 500-gram load, using a rhombus-shaped diamond indenting tool with a longitudinal angle of 172.5 degrees and a traverse angle of 130 degrees. Flexibility test. The matrix band shall be bent back on itself by creasing it in the middle (so that one half is superimposed on the other) and returning i

24、t to its original flat position. The flattening and straightening of the 180 degree bend shall be done using a rubber-covered metal roller weighing 4-/2 plus or minus “2 pounds. performed in the same way with the inside surface of the crease the same for all bends. Subsequent bends shall be 4 Provid

25、ed by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-54675 65 9999974 0066774 7 .- A-A-54 6 7 5 Contractor certification. The contractor shall certify and maintain substantiating evidence that the product of fered meets the salient characteristics of this C

26、ommercial Item Description, and that the product conforms to the producers own drawings, specifications, standards, and quality assurance practices. The government reserves the right to require proof of such conformance prior to first delivery and thereafter as may be otherwise provided for under th

27、e provisions of the contract. 0 Metric products. Products manufactured to metric dimensions will be considered on an equal basis with those manufactured using inch/pound units, providing they fall within the tolerances specified using conversion tables contained in the latest. revision of Federal St

28、andard No. 376, and all other requirements of this document are met. If a product is manufactured to metric dimensions and those dimensions exceed the tolerances specified in the inch/pound units, a request should be made to the contracting officer to determine if the product is acceptable. The cont

29、racting officer has the option of accepting or rejecting the product. Resul.atorv requirements. Federal Food, Druq and Cosmetic Act. If the product covered by this-document has been determined by the U.S. Food and Drug Administration to be under its jurisdiction, the offeror/contractor shall comply,

30、 and be responsible for compliance by its subcontractors/suppliers, with the requirements of the Federal Food, Drug and Cosmetic Act, as amended, and regulations promulgated thereunder. In addition, the offeror/contractor shall comply, and be responsible for compliance by its subcontractors/supplier

31、s, with the requirements of all other applicable Federal, State, and local statutes, ordinances, and regulations. Recovered materials. The offeror/contractor is encouraged to use recovered material in accordance with Federal Acquisition Regulation Subpart 23.4 to the maximum extent practical. 5 Prov

32、ided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I. A-A-54675 65 M 9999974 0066775 9 A-A-5.4 6 7 5 Preservation, packaqinq, p ackinq, labelinq, and markinq. Unless otherwise specified, preservation, packa-ging and packing shall be to a degree of protectio

33、n to peclude damage to containers and/or contents thereof under normal shipping conditions, handling, etc:, involving shipment from the supply source to the receiving activity, plus reshipment from receiving activity, and shall conform to applicable carriers rules and regulations. Intermediate and e

34、xterior package quantities and labeling and marking shall be as specified in the contract and/or order. NOTE: The following National Stock Numbers are covered by this document. National Stock Number Item Identification 6520-00-682-6530 BAND SET, MATRIX, DENTAL, Assorted, Tofflemire, Junior Size, No.

35、 13, 14, and 15, 0.0020 in. thick, set of 12 Tofflemire, Adult Size, No. 3, 0.0015 in. thick, 12s Tofflemire, Adult Size, No. 1, 0.0015 in. thick, 12s Tofflemire, Adult Size, No. 2, 0.0015 in. thick, 12s Assorted, Tofflemire, Adult Size, No. 10 and 11, 0.0015 in. thick, set of 12 Tofflemire, Adult S

36、ize, No. 1, 0.0020 in. thick, 12s 6520-00-721-9351 BAND, MATRIX, DENTAL, 6520-00-721-9355 BAND, MATRIX, DENTAL, 6520-00-721-9356 BAND, MATRIX, DENTAL, 6520-00-817-2297 BAND SET, MATRIX, DENTAL, 6520-01-079-6363 BAND, MATRIX, DENTAL, Orderinq data. Intermediate/exterior package quantities, labeling,

37、and marking must be as specified in the contract anc/or order. MILITARY INTERESTS: Preparing Activity: Custodians: DoD-MB Army-MD Navy-MS Air Force-O3 6 Agent: DLA-DM Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. i I a a A-A-54675 65 W 9779974 00bb77b O CIVIL AGENCY COORDINATING ACTIVITIES: VA-OSS PHS FDA-MPQAS 7 A-A-54 6 7 5 Project No. 6520-2299 Location: PL Disk #2 ( BANDS ) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-