DOD A-A-54468-1991 ROLL ABSORBENT《能吸收的卷》.pdf

《DOD A-A-54468-1991 ROLL ABSORBENT《能吸收的卷》.pdf》由会员分享，可在线阅读，更多相关《DOD A-A-54468-1991 ROLL ABSORBENT《能吸收的卷》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、A-A-544b 65 9779974 0062580 7 m COMMERCIAL ITEM DESCRIPTION l A-A-54 4 68 30 September 1991 ROLL, ABSORBENT The General Services Administration has authorized the use of this Commercial Item Description in preference to Type I of Roll, Absorbent, Cotton and Roll, Cellulose Specification GG-R-563B. S

2、alient Characteristics: Shall be sterile absorbent cotton rolls suitable for use in dental procedures. The rolls shall be sterile when tested in accordance with the USP. The rolls shall be of the following sizes and fifty of the finished rolls shall have the following minimum average weights. MINIMU

3、M AVERAGE DIMENSION WEIGHT OF SIZE f INCHES) 50 ROLLS (GRAMS) 1 3/8 Diameter 2 1/2 Diameter By 6 Long By 1 1/2 Long 70 25 The rolls shall be made from cotton that meets the requirements of Purified Cotton, USP, except for fiber length and except that it shall retain not less than 20 times its weight

4、 of water. The cotton shall be formed into non-collapsible rolls of uniform firmness and consistency. The outer surface of the finished rolls shall be starched or shall be braided with a soft synthetic yarn, or shall be coated with methylcellulose in such a manner as to prevent adhesion or damage to

5、 oral mucous membranes and still be capable of uniform absorption rate. The rolls shall be readily adaptable to mouth contour and shall have a high degree of absorbency. The rolls shall be well formed and shall be free from dirt, lumps, foreign matter and other impurities. AMSCNA FSC 6510 DISTRIBUTI

6、ON STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-33 A-A-54468 65 m 9999974 0062581 9 m A-A-54 4 68 Workmanshig. The absorbent rolls shall be free from defects which detract from t

7、heir appearance or impair their serviceability. Unit. For Size 1 - Box (BX). Fifty absorbent cotton rolls shall be suitably bagged or wrapped and sealed to maintain sterility of contents unless packaged is damaged or opened. One box containing 10 packages of 50 rolls each (500 rolls), as specified,

8、constitutes one unit. As an alternate, 50 absorbent cotton rolls shall be suitably banded in a bundle. Five bundles of 50 rolls each (250 rolls) shall be suitably bagged and sealed to maintain sterility of contents unless package is damaged or opened. One box containing two packages of 250 rolls eac

9、h (500 rolls), as specified, constitutes one unit. For Size 2 - Box (BX). Individual absorbent cotton rolls shall be suitably bagged, wrapped or bundled in groups of not less than 25 rolls nor more than 125 rolls. Each group shall be suitably bagged or wrapped and sealed to maintain sterility of con

10、tents unless package is damaged or opened. One box containing a total of 2000 bagged or wrapped rolls, as specified, constitutes one unit, Quality Assurance Provisions. ResDonsibilitv for inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the

11、performance of all inspection requirements as specified herein. purchase order, the contractor may use his own or any facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the

12、 inspections set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. Except as otherwise specified in the contract or Records. Records of examinations and tests performed by or for the contractor shall be maintain

13、ed by the contractor and made available to the Government upon the Governments request, at any time, or from time to time, during the performance of the contract and for a period of three years after delivery of the supplies to which such records relate. 2 Provided by IHSNot for ResaleNo reproductio

14、n or networking permitted without license from IHS-,-,-A-A-54468 65 a 9999974 0062582 O -? A-A-5 4 4 6 8 InsDection. Inspection, as used herein, is defined as both examination (such as visual and auditory investigation without the use of special laboratory appliances or procedures) and testing (dete

15、rmination by technical means of physical and chemical properties) of the item. SamDlins for examination. Sampling for examination shall be conducted in accordance with MIL-STD-105 and as specified herein. Unit of product for examination purposes shall be one roll. Sampling shall be Inspection level

16、5-4 with an acceptable quality level (AQL) of 2.5 (percent defective). Examination. Examination shall be conducted to determine compliance with specification requirements. Samglins for tests. Sampling for tests shall be conducted in accordance with MIL-STD-105 and as specified herein. Unit of produc

17、t for test purposes chal be one roll. Inspection level S-1 with an AQL of 2.5 (percent defective). Sampling shall be Tests. Tests shall be conducted to determine compliance with specification requirements. Where feasible, the same sample shall be used for the determination of two or more test charac

18、teristics. . Contractor certification. The contractor shall certify that the e product offered meets the salient characteristics of this description and conforms to the producers own drawings, specifications, standards, and quality assurance practices. The conformance prior to first delivery and the

19、reafter as may be otherwise provided for under the provisions of the contract. Government reserves the right to require proof of such Metric Products. Products manufactured to metric dimensions will be considered on an equal basis with those manufactured using inch-pound units, providing they fall w

20、ithin the tolerance specified using conversion tables contained in the latest revision of Federal Standard No. 376, and all other requirements of this document are met. If a product is manufactured to metric dimensions and those dimensions exceed the tolerance specified in the inch/pound units, a re

21、quest should be made to the contracting officer to determine if the product is acceptable. The contracting officer has the option of accepting or rejecting the product. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5L1468 65 3999974 0062583 2

22、 4 A-A-54468 Requlatory reuuirements. Federal Food, Drua and Cosmetic Act. If the product covered by this document has been determined by the U.S. Food and Drug Administration to be under its jurisdiction, the offeror/contractor shall comply, and be responsible for compliance by its subcontractors/s

23、uppliers, with the requirements of the Federal Food, Drug and Cosmetic Act, as amended, and regulations promulgated thereunder. In addition, the offeror/contractor shall comply, and be responsible for compliance by its subcontractors/suppliers, with the requirements of all other applicable Federal,

24、State, and local statutes, ordinances, and regulations. Recovered materials. The offeror/contractor is encouraged to use recovered material in accordance with Federal Acquisition Regulation Subpart 23.4 to the maximum extent practical. Preservation, packaqinq, P ackinq, labelinq and markinq. Unless

25、otherwise specified, preservation, packaging, and packing shall be to a degree of protection to preclude damage to containers and/or contents thereof under normal shipping conditions, handling, etc., involving shipment from the supply source to the receiving activity, plus reshipment from receiving

26、activity, and shall conform to applicable carriers rules and regulations. Intermediate and exterior package quantities and labeling and marking shall be as specified in the contract and/or order. NOTE: document : The following National Stock Numbers are covered by this - NSN ITEM IDENTIFICATION SIZE

27、 6510-00-518-1900 ROLL, ABSORBENT, COTTON, 3/8 By 6 Inches, 500s 6510-01-073-1331 ROLL, ABSORBENT, COTTON, 1/2 By 11/2 Inches, 2000s Ordering data. labeling and marking must be specified in the contract and/or order. Intermediate/exterior package quantities and 4 1 2 Provided by IHSNot for ResaleNo

28、reproduction or networking permitted without license from IHS-,-,-& r. .- A-A-5 4 4 68 0 MILITARY INTERESTS : Custodians: Army - MD Navy - MS Air Force - 03 PREPARING ACTIVITY: DoD - MB CIVIL AGENCY COORDINATING ACTIVITY: VA-OSS PHS FDA-MPQAS Agent : DLA-DM PGC 05086 5 Project No. 6510-0778 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-