DLA SMD-5962-97543 REV D-2010 MICROCIRCUIT DIGITAL LOW VOLTAGE CMOS OCTAL BUS TRANSCEIVER WITH THREE-STATE OUTPUTS MONOLITHIC SILICON.pdf

《DLA SMD-5962-97543 REV D-2010 MICROCIRCUIT DIGITAL LOW VOLTAGE CMOS OCTAL BUS TRANSCEIVER WITH THREE-STATE OUTPUTS MONOLITHIC SILICON.pdf》由会员分享，可在线阅读，更多相关《DLA SMD-5962-97543 REV D-2010 MICROCIRCUIT DIGITAL LOW VOLTAGE CMOS OCTAL BUS TRANSCEIVER WITH THREE-STATE OUTPUTS MONOLITHIC SILICON.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add device type 02. Add vendor CAGE 27014 to device type 02. Editorial changes throughout. JAK 98-11-23 Monica L. Poelking B Correct VCCconditions for IOZHand IOZLtests for device type 01 in talbe I. Add footnote to ICCtest in table I. Correct VT

2、ESTin note 3, figure 5. Update boilerplate to MIL-PRF-38535 requirements. Editorial changes throughout. TVN 03-05-20 Thomas M. Hess C Add footnote to ICCin table I. Add table III, delta limits. Editorial changes throughout. TVN 03-07-14 Thomas M. Hess D Update boilerplate paragraphs to the current M

3、IL-PRF-38535 requirements. - LTG 10-11-22 Thomas M. Hess REV SHET REV D D D SHEET 15 16 17 REV STATUS REV D D D D D D D D D D D D D D OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Joseph A. Kerby DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil STANDARD

4、MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE AMSC N/A CHECKED BY Charles F. Saffle, Jr. APPROVED BY Monica L. Poelking MICROCIRCUIT, DIGITAL, LOW VOLTAGE CMOS, OCTAL BUS TRANSCEIVER WITH THREE-STATE OUTPUTS, MONOLITHIC SILICON DR

5、AWING APPROVAL DATE 97-06-13 REVISION LEVEL D SIZE A CAGE CODE 67268 5962-97543 SHEET 1 OF 17 DSCC FORM 2233 APR 97 5962-E013-11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-97543 DLA LAND AND MARITIME COL

6、UMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are availabl

7、e and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 97543 01 Q R A Federal stock class designator RHA designator (see 1.2.1) Device ty

8、pe (see 1.2.2)Device class designatorCase outline (see 1.2.4) Leadfinish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marke

9、d devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 54LVCH245A Oc

10、tal bus transceiver with bus hold circuit and three-state outputs02 54LCX245 Octal bus transceiver with three-state outputs 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation

11、 M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as fol

12、lows: Outline letter Descriptive designator Terminals Package style R GDIP1-T20 or CDIP2-T20 20 Dual-in-line S GDFP2-F20 or CDFP3-F20 20 Flat pack 2 CQCC1-N20 20 Square leadless chip carrier 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-385

13、35, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-97543 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum rat

14、ings. 1/ 2/ 3/ Supply voltage range (VCC) -0.5 V dc to +6.5 V dc DC input voltage range (VIN): Except I/O ports . -0.5 V dc to +6.5 V dc 4/ I/O ports . -0.5 V dc to VCC+ 0.5 V dc 4/ 5/ DC output voltage range (VOUT): High or low state -0.5 V dc to VCC+ 0.5 V dc 4/ 5/ High-impedance or power-off stat

15、e -0.5 V dc to 6.5 V dc 4/ DC input clamp current (IIK) (VIN 0.0 V) . -50 mA DC output clamp current (IOK) (VOUT 0.0 V or VOUT VCC) . 50 mA Continuous output current (IOUT) (VOUT= 0.0 to VCC) 50 mA Continuous current through VCCor GND . 100 mA Maximum power dissipation at TA= +55C (in still air) . 5

16、00 mW 6/ Storage temperature range (TSTG) . -65C to +150C Lead temperature (soldering, 10 seconds) +300C Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 Junction temperature (TJ) +175C 1.4 Recommended operating conditions. 2/ 3/ 7/ Supply voltage range (VCC): Operating . +2.0 V dc to +3

17、.6 V dc Data retention only (minimum) . +1.5 V dc Input voltage range (VIN) 0.0 V to +5.5 V dc Output voltage range (VOUT): High or low state 0.0 V to VCCHigh-impedance state 0.0 V to +5.5 V dc Minimum high level input voltage (VIH) (VCC= 2.7 V to 3.6 V) +2.0 V dc Maximum low level input voltage (VI

18、L) (VCC= 2.7 V to 3.6 V) . +0.8 V dc Maximum high level output current (IOH): VCC= 2.7 V -12 mA VCC= 3.0 V -24 mA Maximum low level output current (IOL): VCC= 2.7 V +12 mA VCC= 3.0 V +24 mA Input transition rise or fall rate (t/v) 0 ns/V to 10 ns/V Case operating temperature range (TC) . -55C to +12

19、5C 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Unless otherwise noted, all voltages are referenced to GND. 3/ The limits for the parameters specified herein shall a

20、pply over the full specified VCCrange and case temperature range of -55C to +125C. 4/ The input and output negative voltage ratings may be exceeded provided that the input and output clamp current ratings are observed. 5/ The value of VCCis provided in the recommended operating conditions section 1.

21、4 above. 6/ The maximum package power dissipation is calculated using a junction temperature of 150C and a board trace length of 750 mils. 7/ Unused inputs must be held high or low to prevent them from floating. Provided by IHSNot for ResaleNo reproduction or networking permitted without license fro

22、m IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-97543 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 4 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part o

23、f this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS

24、 MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available onli

25、ne at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing

26、 takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specifie

27、d herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN cla

28、ss level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outline

29、s. The case outlines shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth table shall be as specified on figure 2. 3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3. 3.2.5

30、 Ground bounce load circuit and waveforms. The ground bounce load circuit and waveforms shall be as specified on figure 4. 3.2.6 Switching waveforms and test circuit. The switching waveforms and test circuit shall be as specified on figure 5. 3.3 Electrical performance characteristics and postirradi

31、ation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full case operating temperature range. 3.4 Electrical test requirements. The electrical test requirements sh

32、all be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-97543 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990

33、 REVISION LEVEL D SHEET 5 DSCC FORM 2234 APR 97 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the o

34、ption of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certifica

35、tion/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of co

36、mpliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see

37、6.6.2 herein). The certificate of compliance submitted to DLA Land and Maritime-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the

38、requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.

39、8 Notification of change for device class M. For device class M, notification to DLA Land and Maritime-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device

40、class M, DLA Land and Maritime, DLA Land and Maritimes agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignm

41、ent for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 37 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-97543 DLA LAND

42、AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test and MIL-STD-883 test method 1/ Symbol Test conditions 2/ -55C TC +125C +2.0 V VCC +3.6 V unless otherwise specified Device type VCCGroup A subgroups Limits 3/ U

43、nit Min Max High level output voltage 3006 VOHFor all inputs affecting output under test, VIN= VIHor VIL For all other inputs, VIN= VCCor GND IOH= -100 A All 2.7 V and 3.6 V 1, 2, 3 VCC-0.2 V IOH= -12 mA 2.7 V 1, 2, 3 2.2 3.0 V 2.4 IOH= -24 mA 3.0 V 1, 2, 3 2.2 Low level output voltage 3007 VOLFor a

44、ll inputs affecting output under test, VIN= VIHor VILFor All other inputs, VIN= VCCor GND IOL= 100 A All 2.7 V and 3.6 V 1, 2, 3 0.2 V IOL= 12 mA 2.7 V 1, 2, 3 0.4 IOL= 24 mA 3.0 V 1, 2, 3 0.55 Input current high 3010 IIHFor input under test, VIN= 5.5 V For all other inputs, VIN= VCCor GND 01 3.6 V

45、1, 2, 3 +15.0 A 02 +5.0 Input current low 3009 IILFor input under test, VIN= 0.0 V For all other inputs, VIN= VCCor GND 01 3.6 V 1, 2, 3 -15.0 A 02 -5.0 Input bus hold current II(hold) VIN= 0.8 V 01 3.0 V 1, 2, 3 75 A VIN= 2.0 V 3.0 V -75 VIN= 0.0 V to 3.6 V 4/ 3.6 V 500 Three-state output leakage c

46、urrent high 3021 IOZH5/ VOUT= 5.5 V 01 3.6 V 1, 2, 3 +15.0 A VOUT= 3.6 V or 5.5 V 2.7 V +50.0 VOUT= 5.5 V 02 2.7 V and 3.6 V +5.0 Three-state output leakage current low 3020 IOZL5/ VOUT= GND 01 3.6 V 1, 2, 3 -15.0 A VOUT= GND 2.7 V -50.0 VOUT= GND 02 2.7 V and 3.6 V -5.0 Quiescent supply current 300

47、5 ICCFor all inputs, VIN= VCCor GND IOUT= 0.0 A All 3.6 V 1, 2, 3 10.0 A For all inputs, 3.6 V VIN 5.5 V IOUT= 0.0 A 6/ 10.0 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-9754

48、3 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test and MIL-STD-883 test method 1/ Symbol Test conditions 2/ -55C TC +125C +2.0 V VCC +3.6 V unless otherwise specified Device type VCCGroup A subgroups Limits 3/ Unit Min Max Quiescent supply current delta, TTL input levels 3005 ICC7/ One input at VCC- 0.6 V Other inputs at VCCor GND All 2.7 V and 3.6 V 1, 2, 3 500.0 A Input capacitance, control inputs 3012 CINTC= +25C VIN= VCCor GND See 4.4.1c All 3.3 V 4 12.