DLA SMD-5962-96851 REV C-2008 MICROCIRCUIT DIGITAL ADVANCED HIGH SPEED CMOS OCTAL BUFFER DRIVER WITH OUTPUTS TTL COMPATIBLE INPUTS MONOLITHIC SILICON.pdf

《DLA SMD-5962-96851 REV C-2008 MICROCIRCUIT DIGITAL ADVANCED HIGH SPEED CMOS OCTAL BUFFER DRIVER WITH OUTPUTS TTL COMPATIBLE INPUTS MONOLITHIC SILICON.pdf》由会员分享，可在线阅读，更多相关《DLA SMD-5962-96851 REV C-2008 MICROCIRCUIT DIGITAL ADVANCED HIGH SPEED CMOS OCTAL BUFFER DRIVER WITH OUTPUTS TTL COMPATIBLE INPUTS MONOLITHIC SILICON.pdf（17页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes in accordance with NOR 5962-R363-97. - JAK 97-06-27 Monica L. Poelking B Changes in accordance with NOR 5962-R452-97. - CFS 97-09-12 Monica L. Poelking C Update boilerplate to current MIL-PRF-38535 requirements. - MAA 08-05-14 Thomas M. H

2、ess REV SHEET REV SHEET REV C C SHEET 15 16 REV C C C C C C C C C C C C C C REV STATUS OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Joseph A. Kerby CHECKED BY Monica L. Poelking DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218 - 3990 http:/www.dscc.dla.mil APPROVED BY Mon

3、ica L. Poelking DRAWING APPROVAL DATE 96-09-05 MICROCIRCUIT, DIGITAL, ADVANCED HIGH SPEED CMOS, OCTAL BUFFER/DRIVER WITH OUTPUTS, TTL COMPATIBLE INPUTS, MONOLITHIC SILICON SIZE A CAGE CODE 67268 5962-96851 STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIE

4、S OF THE DEPARTMENT OF DEFENSE AMSC N/A REVISION LEVEL C SHEET 1 OF 16 DSCC FORM 2233 APR 97 5962-E535-96 Provided by IHSNot for Resale-,-,-SIZE A 5962-96851 STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218 - 3990 REVISION LEVEL C SHEET 2 DSCC FORM 2234 APR 97 1. SCO

5、PE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available,

6、 a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 96851 01 Q R A Federal RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4)

7、(see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are

8、 marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 54AHCT540 Octal buffer/driver with three-state outputs, TTL compatible inputs 1.2.3 De

9、vice class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with M

10、IL-PRF-38535, appendix A. Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style R GDIP1-T20 or CDIP2-T20 20 Dual-in-line S GDFP2-F20 or CDFP3-F

11、20 20 Flat pack 2 CQCC1-N20 20 Square leadless chip carrier 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHSSIZ

12、E A 5962-96851 STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218 - 3990 REVISION LEVEL C SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ 2/ 3/ Supply voltage range (VCC) -0.5 V dc to +7.0 V dc DC input voltage range (VIN) -0.5 V dc to +7.0 V dc 4/ DC ou

13、tput voltage range (VOUT) . -0.5 V dc to VCC+ 0.7 V dc 4/ DC input clamp current (IIK) (VINVCC) . -20 mA DC output clamp current (IOK) (VOUTVCC). 20 mA Continuous output current (IOUT) (VOUT= 0.0 V to VCC) 25 mA Continuous current through VCCor GND 75 mA Maximum power dissipation at TA= +55C (in sti

14、ll air) (PD ) 500 mW Storage temperature range (TSTG) . -65C to +150C Lead temperature (soldering, 10 seconds). +300C Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 Junction temperature (TJ) +175C 1.4 Recommended operating conditions. 2/ 3/ Supply voltage range (VCC) +4.5 V dc to +5.5

15、V dc Minimum high level input voltage (VIH). +2.0 V Maximum low level input voltage (VIL) +0.8 V Input voltage range (VIN) +0.0 V dc to 5.5 V Output voltage range (VOUT). +0.0 V dc to VCCMaximum high level output current (IOH) -8 mA Maximum low level output current (IOL) +8 mA Maximum input rise or

16、fall rate (t/V) 20 ns/V Case operating temperature range (TC). -55C to +125C 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Unless otherwise noted, all voltages are re

17、ferenced to GND. 3/ The limits of the parameters specified herein shall apply over the full specified VCCrange and case temperature range of -55C to +125C. Unused inputs must be held high or low 4/ The input and output voltage ratings may be exceeded provided that the input and output current rating

18、s are observed. Provided by IHSNot for Resale-,-,-SIZE A 5962-96851 STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218 - 3990 REVISION LEVEL C SHEET 4 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following sp

19、ecification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation. or contract DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General

20、 Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Draw

21、ings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Non-Government publications. The following document(s) form a part of this document to t

22、he extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. ELECTRONIC INDUSTRIES ALLIANCE (EIA) JESD 7A - Standard for Description of 54/74HCXXXX and 54/74HCTXXXX High-Speed CMOS Devices. (Copies of these documents are avail

23、able online at http:/www.eia.org/ or from the Electronic Industries Alliance, 2500 Wilson Boulevard, Arlington, VA 22201-3834.) 2.3 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in

24、this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the

25、 device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as spec

26、ified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be

27、in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth table shall be as specified on figure 2. 3.2.4 Block or Logic diagram. The block or logic diagram shall be as specified on figure 3. 3.2.5 Ground boun

28、ce load circuit and waveforms. The ground bounce load circuit and waveforms shall be as specified on figure 4. Provided by IHSNot for Resale-,-,-SIZE A 5962-96851 STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218 - 3990 REVISION LEVEL C SHEET 5 DSCC FORM 2234 APR 97 3

29、.2.6 Switching waveforms and test circuit. The switching waveforms and test circuit shall be as specified on figure 5. 3.3 Electrical performance characteristics and post-irradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and post-irradiation

30、parameter limits are as specified in table I and shall apply over the full case operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. Th

31、e part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product

32、 using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes

33、 Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer

34、 in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-

35、VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conform

36、ance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to

37、 DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufactur

38、ers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 36 (see MIL-PRF-38535,

39、 appendix A). Provided by IHSNot for Resale-,-,-SIZE A 5962-96851 STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218 - 3990 REVISION LEVEL C SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Limits 3/ Test and MIL-STD-883 test method 1/ Sym

40、bol Test conditions 2/ -55C TC +125C +4.5 V VCC +5.5 V unless otherwise specified VCCGroup A subgroups Min Max Unit IOH= -50 A 1, 2, 3 4.4 1 3.94 High level output voltage 3006 VOHFor all inputs affecting output under test, VIN= 2.0 V or 0.8 VFor all other inputs, VIN= VCCor GND IOH= -8 mA 4.5 V 2,

41、3 3.8 V IOL= +50 A 1, 2, 3 0.1 1 0.36 Low level output voltage 3007 VOLFor all inputs affecting output under test, VIN= 2.0 V or 0.8 VFor all other inputs, VIN= VCCor GND IOL= +8 mA 4.5 V 2, 3 0.44 V 1 +0.1 Input current high 3010 IIHFor input under test, VIN= VCCFor all other inputs, VIN= VCCor GND

42、 5.5 V 2, 3 +1.0 A 1 -0.1 Input current low 3009 IILFor input under test, VIN= GND For all other inputs, VIN= VCCor GND 5.5 V 2, 3 -1.0 A 1 +0.25 Three - state output leakage current high 3021 IOZH_ OEn = 2.0 V For all other inputs, VIN= VCCor GND VOUT= VCC5.5 V 2, 3 +2.5 A 1 -0.25 Three - state out

43、put leakage current low 3020 IOZH_ OEn = 2.0 V For all other inputs, VIN= VCCor GND VOUT= GND 5.5 V 2, 3 -2.5 A 1 4.0 Quiescent supply current 3005 ICCFor all inputs, VIN= VCCor GND IOUT= 0.0 A 5.5 V 2, 3 40.0 A 1 1.35 Quiescent supply current delta, TTL input levels 3005 ICC4/ For input at 3.4 V Ot

44、her inputs at VCCor GND 5.5 V 2, 3 1.5 mA Input capacitance 3012 CINTC= +25C, VIN= VCCor GND See 4.4.1c 5.0 V 4 10.0 pF Output capacitance 3012 COUTTC= +25C, VOUT= VCCor GND See 4.4.1c 5.0 V 4 10.0 pF Power dissipation capacitance CPD5/ CL= 50 pF minimum f = 1 MHz See 4.4.1c 5.0 V 4 14.0 pF See foot

45、notes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHSSIZE A 5962-96851 STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218 - 3990 REVISION LEVEL C SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performanc

46、e characteristics - Continued. Limits 3/ Test and MIL-STD-883 test method 1/ Symbol Test conditions 2/ -55C TC +125C +4.5 V VCC +5.5 V unless otherwise specified VCCGroup A subgroups Min Max Unit VOLP6/ 5.0 V 4 1900 mV Low level ground bounce noise VOLV6/ 5.0 V 4 -1700 mV VOHP6/ 5.0 V 4 800 mV High

47、level VCCbounce noise VOHV6/ VIH= 3.0 V, VIL= 0.0 V TA= +25C See 4.4.1d See figure 4 5.0 V 4 -1000 mV 4.5 V Functional test 3014 7/ VIH= 2.0 V, VIL= 0.8 V Verify output VOSee 4.4.1b 5.5 V 7, 8 L H 9 6.0 CL= 15 pF minimum 9/ See figure 5 4.5 V and 5.5 V 10, 11 1.0 7.5 9 8.5 Propagation delay time, An

48、 to Yn 3003 tPLH, tPHL 8/ CL= 50 pF minimum See figure 5 4.5 V and 5.5 V 10, 11 1.0 10.0 ns 9 8.0 CL= 15 pF minimum RL= 1 k See figure 5 9/ 4.5 V and 5.5 V 10, 11 1.0 9.0 9 11.0 Propagation delay time, output enable _ OEn to Yn 3003 tPZH, tPZL 8/ CL= 50 pF minimum RL= 1 k See figure 5 4.5 V and 5.5 V 10, 11 1.0 12.0 ns 9 8.0 CL= 15 pF minimum RL= 1 k See figure 5 9/ 4.5 V and 5.5 V 10, 11 1.0 9.0 9 11.0 Propagation delay time, output disable _ OEn to Yn 3003 tPHZ, tPLZ 8/ CL= 50 pF minimum RL= 1 k See figure 5 4.5 V and 5.5 V 10, 11 1.0 12.0 ns