DLA SMD-5962-89870 REV C-2011 MICROCIRCUIT LINEAR NEGATIVE 8-VOLT REGULATOR FIXED MONOLITHIC SILICON.pdf

《DLA SMD-5962-89870 REV C-2011 MICROCIRCUIT LINEAR NEGATIVE 8-VOLT REGULATOR FIXED MONOLITHIC SILICON.pdf》由会员分享，可在线阅读，更多相关《DLA SMD-5962-89870 REV C-2011 MICROCIRCUIT LINEAR NEGATIVE 8-VOLT REGULATOR FIXED MONOLITHIC SILICON.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Drawing updated to reflect current requirements. - ro 01-02-15 R. MONNIN B Add a footnote to case outline U, TO-257 package as specified under 1.2.2 and figure 1. -rrp 05-02-04 R. MONNIN C Update boilerplate paragraphs to current MIL-PRF-38535 re

2、quirements. - ro 11-05-12 C. SAFFLE THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED. REV SHET REV SHET REV STATUS REV C C C C C C C C C C C C C OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 PMIC N/A PREPARED BY JOSEPH A. KERBY DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.dscc

3、.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY CHARLES E. BESORE APPROVED BY MICHAEL A. FRYE MICROCIRCUIT, LINEAR, NEGATIVE 8-VOLT REGULATOR, FIXED, MONOLITHIC SILICON DRAWING APPROVAL DATE 92-01-13 AMS

4、C N/A REVISION LEVEL C SIZE A CAGE CODE 67268 5962-89870 SHEET 1 OF 13 DSCC FORM 2233 APR 97 5962-E224-11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89870 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990

5、REVISION LEVEL C SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the followi

6、ng example: 5962-89870 01 T A Drawing number Device type (see 1.2.1) Case outline(see 1.2.2) Lead finish(see 1.2.3)1.2.1 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 7908A Negative regulator, fixed 8 volt 1.2.2 Case outli

7、ne(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style T See figure 1 3 TO-257, single row, flange mount, glass sealed U 1/ See figure 1 3 TO-257, single row, flange mount, with isolated tab and glass sealed X See fi

8、gure 1 3 TO-39, can Y See figure 1 2 TO-3, flange mount Z MBFM4-P2 2 Flange mount 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A. _ 1/ For outline letter U, CAGE 34333 manufacturers the TO-257 package with ceramic seal. Provided by IHSNot for ResaleNo reproduction or

9、 networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89870 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. Input voltage: Operating or output shorted to ground -35 V dc Transient . -4

10、3 V dc 2/ Power dissipation (PD): TC= +25C: Cases T, U, and Z . 15 W Case X . 2 W Case Y . 20 W TA= +25C: Cases T, U, and Z . 3.0 W Case X . 1.0 W Case Y . 4.3 W Storage temperature range . -65C to +150C Lead temperature (soldering, 10 seconds) . +300C Junction temperature (TJ) . +150C 3/ Thermal re

11、sistance, junction-to-case (JC): Case T 3.5C/W Case U 4.2C/W Case X 15C/W Case Y 3C/W Case Z 6C/W Thermal resistance, junction-to-ambient (JA): Cases T, U, and Z . 42C/W Case X 120C/W Case Y 35C/W 1.4 Recommended operating conditions. Input voltage range (VIN) -10.5 V dc to 25.0 V dc Long term stabi

12、lity (VOUT/ t) 32 mV 4/ Ambient operating temperature range (TA) -55C to +125C _ 2/ The 43 V input rating refers to the ability of the regulator to withstand high line or transient condition without damage. Since the regulators maximum current capability is reduced, the output may fall out of regula

13、tion at high input voltages under nominal loading. 3/ The device is protected by a thermal shutdown circuit which is designed to turn off the output transistor whenever the device junction temperature is in excess of +150C. 4/ TA= +25C, t = 1,000 hours. Provided by IHSNot for ResaleNo reproduction o

14、r networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89870 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 4 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specificati

15、on, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specific

16、ation for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Co

17、pies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the referen

18、ces cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535,

19、 appendix A for non-JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-PRF-38535 may be processed as

20、QML product in accordance with the manufacturers approved program plan and qualifying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan may make modifications to the requirements herein. These modifications shall not affect form, fit,

21、 or function of the device. These modifications shall not affect the PIN as described herein. A “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 is required to identify when the QML flow option is used. 3.2 Design, construction, and physical dimensions. The design, construction, and

22、physical dimensions shall be as specified in MIL-PRF-38535, appendix A and herein. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.2 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.3 Electrical performance characte

23、ristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The e

24、lectrical tests for each subgroup are described in table I. 3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN

25、number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. 3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance to MIL-PRF-38535, appendix A. The compliance indicator

26、 “C” shall be replaced with a “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89870 DLA LAND AND

27、MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ -55C TA+125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Output voltage VOUTTA= +25C 1 01 -7.88 -8.12 V VIN= -

28、11.5 V to -25 V 2/ 1,2,3 -7.7 -8.3 Line regulation 3/ 4/ VRLINEVIN= -10.5 V to -25 V 1 01 40 mV 2,3 70 VIN= -11 V to -17 V 1 20 2,3 40 Load regulation 3/ VRLOADIOUT= 5.0 mA to 1.5 A 5/ 1 01 80 mV 2,3 150 IOUT= 250 mA to 750 mA 5/ 1 30 2,3 60 IOUT= 5 mA to 500 mA 6/ 1 30 2,3 60 Standby current drain

29、ISCD1 01 2.0 mA 2,3 2.5 Standby current drain change with line ISCD(line) VIN= -11.5 V to -25 V 1,2,3 01 1.0 mA Standby current drain change with load ISCDIOUT= 5.0 mA to 1.0 A 5/ 1,2,3 01 0.5 mA (load) IOUT= 5.0 mA to 500 mA 6/ 0.5 Dropout voltage VDOIOUT= 1.0 A, 5/ VOUT= 100 mV 1,2,3 01 2.3 V IOUT

30、= 500 mA, 6/ VOUT= 100 mV 2.3 Peak output current IOUTTA= +25C 5/ 1 01 1.5 3.3 A (pk) TA= +25C 6/ 0.5 1.4 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89870 DLA LAND AND MARI

31、TIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ -55C TA+125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Short circuit current 7/ IOSVIN= 35 V 5/ 1 01 1

32、.2 A 2,3 2.8 VIN= 35 V 6/ 1 0.6 2,3 2.0 Ripple rejection 3/ VIN/ VIN= 10 V, f = 120 Hz 4 01 54 dB VOUT5,6 8/ 50 Output noise voltage 8/ NOf = 10 Hz to 100 kHz, TA= +25C 7 01 80 V / Vrms 1/ Unless otherwise specified, VIN= -14 V and IOUT= 500 mA for cases U, T, Y, and Z, VIN= -14 V and IOUT= 100 mA f

33、or case X. Maximum test current for case X is 500 mA. 2/ For case X: IOUT= 5 mA to 500 mA, P 2 W. For case Y: IOUT= 5 mA to 1.0 A, P 20 W. For cases U, T, and Z: IOUT= 5 mA to 1.0 A, P 15 W. 3/ All measurements except output noise voltage and ripple rejection are made at constant junction temperatur

34、e with low duty cycle testing. 4/ Minimum load current for full line regulation is 5.0 mA. 5/ For cases T, U, Y, and Z only. 6/ For case X only. 7/ Short circuit protection is only assured up to VIN= -35 V. 8/ Guaranteed, if not tested, to the limits specified in table I herein. Provided by IHSNot f

35、or ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89870 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 7 DSCC FORM 2234 APR 97 Case outlines T and U Inches mm .005 0.13 .010 0.25 .020 0.51 Symbol Inches Mil

36、limeters Min Max Min Max A .190 .200 4.83 5.08 A1.035 .045 0.89 1.14A2.120 BSC 3.05 BSC b .025 .035 0.64 0.89 D .645 .665 16.38 16.89D1.410 .430 10.41 10.92 D3.000 .065 0.00 1.65e .100 BSC 2.54 BSC E .410 .422 10.41 10.72 L .500 .750 12.70 19.05O .527 .537 13.39 13.64 P .140 .150 3.56 3.81NOTES: 1.

37、Dimensions are in inches. 2. Metric equivalent are given for general information only. 3. For case outline U only, CAGE 34333, the ceramic seal that protrudes from the seating plane is not to be considered in overall package dimensions. The ceramic seal protrusion is considered uncontrolled within a

38、n area 30 mils from the seating plane. FIGURE 1. Case outline. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89870 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 8 DSCC FORM 2234 APR

39、 97 Case outline X Symbol Inches Millimeters Notes Min Max Min Max A .165 .185 4.19 4.70 b .016 .019 0.41 0.48 2 b1.016 .021 0.41 0.53 2 D .335 .370 8.51 9.40 D1.305 .335 7.75 8.51 e .200 BSC 5.08 BSC 4 e1.100 BSC 2.54 BSC 4 F - .050 - 1.27 k .028 .034 0.71 0.86 k1.029 .045 0.74 1.14 3 k2.009 .041 0

40、.23 1.04 L .500 - 12.70 - L1- .050 - 1.27 L2.250 - 6.35 - 45 T.P. 45 T.P. 4 NOTES: 1. Dimensions shall be measured in inches. 2. Metric equivalents are given for general information only. 3. All leads b applies between L1and L2. b1applies between L2and .500 inch (12.70 mm) from the reference plane.

41、Diameter is uncontrolled in L1and beyond .500 inch (12.70 mm) from the reference plane. 4. Measured from the maximum diameter of the product. 5. Leads having a maximum diameter of .019 inch (0.48 mm) measured in gauging plane .054 inch (1.37 mm) + .001 (0.03 mm) - .000 inch (0.00 mm) below the base

42、plane of the product shall be within .007 inch (0.18 mm) of their true-position relative to a maximum width tab. 6. The product may be measured by direct method or by guage. FIGURE 1. Case outline Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IH

43、S-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89870 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 9 DSCC FORM 2234 APR 97 Case outline Y Symbol Inches Millimeters Notes Min Max Min Max A .250 .450 6.35 11.35 A11.177 1.197 29.90 30.40b .038 .043 0.97 1.09 2,6 D - .875 - 22.

44、22 e .655 .675 16.64 17.74 e1.420 .440 10.67 11.16 e2.205 .225 5.21 5.72F .060 .135 1.52 3.43 H .151 .161 3.84 4.09 4,5L .312 .500 7.92 12.70 3 L1- .050 - 1.27 2,3 R .495 .525 12.57 13.34 R1.131 .188 3.33 4.78NOTES: 1. Dimensions shall be measured in inches. 2. Metric equivalents are given for gener

45、al information only. 3. (Two leads) b applies between L1and beyond .500 inch (12.70 mm) from the seating plane. Diameter is uncontrolled in L1and beyond .500 inch (12.70 mm) from the seating plane. 4. Two leads. 5. Two holes. 6. Two holes located at true position within diameter .010 inch (0.25 mm).

46、 7. Leads having a maximum diameter of .043 inch (1.09 mm) measured in gauging plane .054 inch (1.37 mm) .001 (0.03 mm) .000 inch (0.00 mm) below the seating plane shall be located at true position within diameter .014 inch (0.36 mm). 8. The mounting surface of the header shall be flat to convex wit

47、hin .003 inch (0.08 mm) inside a .930 inch (23.62 mm) diameter circle on the center of the header and flat to convex within .006 inch (0.15 mm) overall. FIGURE 1. Case outline Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROC

48、IRCUIT DRAWING SIZE A 5962-89870 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 10 DSCC FORM 2234 APR 97 FIGURE 2. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89870 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 11 DSCC FORM 2234 APR