DLA SMD-5962-89615 REV F-2011 MICROCIRCUIT LINEAR RS-485 DIFFERENTIAL BUS TRANSCEIVER MONOLITHIC SILICON.pdf

《DLA SMD-5962-89615 REV F-2011 MICROCIRCUIT LINEAR RS-485 DIFFERENTIAL BUS TRANSCEIVER MONOLITHIC SILICON.pdf》由会员分享，可在线阅读，更多相关《DLA SMD-5962-89615 REV F-2011 MICROCIRCUIT LINEAR RS-485 DIFFERENTIAL BUS TRANSCEIVER MONOLITHIC SILICON.pdf（25页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add outline letter “H”. Power dissipation = 935 mW, derate at 6.6 mW/C above TA= +25C. Lead temperature for outline letter H with soldering at 10 seconds is +265C. Add case outline H terminal connections to figure 1. Changes in accordance with N.

2、O.R. 5962-R001-92. 91-10-08 M. A. FRYE B Table I. Input resistance test, RIN; add test conditions “Untested input = 0 V, VI= 12 V and -7 V, guaranteed by “line input current”.” Changes in accordance with N.O.R. 5962-R222-94. 94-06-29 M. A. FRYE C Add case outline X. Change format for device classes

3、Q and V. Changes to 1.3, 1.4, and table. Redrawn. - drw 98-07-09 R. MONNIN D Add radiation hardened information. - drw 99-02-01 R. MONNIN E Make change to 3.2.4. Delete figure 1 and figure 4. Add new footnote five to table I. - ro 01-04-20 R. MONNIN F Add paragraph 3.1.1 and Appendix A for microcirc

4、uit die. Delete footnote 3/ from paragraph 1.5 and footnote 2/ from Table I. Delete paragraphs 4.4.4.1.1 and 4.4.4.2. - ro 11-03-22 C. SAFFLE THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED. REV SHET REV F F F F F F F F F F SHEET 15 16 17 18 19 20 21 22 23 24 REV STATUS REV F F F F F F F

5、F F F F F F F OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY RICK C. OFFICER DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHEC

6、KED BY CHARLES E. BESORE APPROVED BY MICHAEL A. FRYE MICROCIRCUIT, LINEAR, RS-485 DIFFERENTIAL BUS TRANSCEIVER, MONOLITHIC SILICON DRAWING APPROVAL DATE 90-10-18 AMSC N/A REVISION LEVEL F SIZE A CAGE CODE 67268 5962-89615 SHEET 1 OF 24 DSCC FORM 2233 APR 97 5962-E215-11 Provided by IHSNot for Resale

7、No reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89615 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting

8、 of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.

9、2 PIN. The PIN is as shown in the following examples. For device classes M and Q: 5962 - 89615 01 P A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2)Case outline (see 1.2.4)Lead finish (see 1.2.5) / /Drawing number For device class V: 5962 F 89615 01 V X A Federal s

10、tock class designator RHA designator (see 1.2.1) Device type (see 1.2.2)Device class designatorCase outline (see 1.2.4) Leadfinish (see 1.2.5) / (see 1.2.3) /Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with

11、 the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Dev

12、ice type Generic number Circuit function 01 DS16F95 RS-485 differential bus transceiver 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as listed below. Since the device class designator has been added after the original issuance

13、of this drawing, device classes M and Q designators will not be included in the PIN and will not be marked on the device. Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with M

14、IL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89615 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 3

15、DSCC FORM 2234 APR 97 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style H GDFP1-F10 or CDFP2-F10 10 Flat pack P GDIP1-T8 or CDIP2-T8 8 Dual-in-line X GDFP1-G10 10 Flat pack with gullwing leads 2

16、CQCC1-N20 20 Square leadless chip carrier 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. 1.3 Absolute maximum ratings. 1/ Supply voltage (VCC) +7.0 V dc Differential input voltage . -10 V/+15 V dc Enable

17、 input voltage . 5.5 V dc Lead temperature: Case P (soldering, 60 seconds) +300C Case 2, H and X (soldering, 10 seconds) +260C Storage temperature . -65C to +175C Junction temperature (TJ) . +175C Power dissipation (PD): 2/ Case P 1274 mW Case 2 . 1800 mW Case H and X 725 mW Thermal resistance, junc

18、tion-to-case (JC): Case P 14C/W Case 2 . 17C/W Case H and X 18C/W Thermal resistance, junction-to-ambient (JA): Case P at 1 W . 118C/W Case 2 . 83C/W Case H and X at 0.5 W . 207C/W 1.4 Recommended operating conditions. Supply voltage range (VCC) +4.5 V dc to +5.5 V dc Ambient operating temperature r

19、ange (TA) -55C to +125C Voltage at any bus terminal: (separately or common mode, VIor VCM) . -7.0 V to +12 V dc Differential input voltage (VID) -7.0 V to +12 V dc Output current HIGH (IOH) : Driver -60 mA Receiver -400 A Output current LOW (IOL) : Driver 60 mA Receiver 16 mA _ 1/ Stresses above the

20、 absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Must withstand the added PDdue to short circuit test, e.g., IOS. Derate above TA= +25C, 8.5 mW/C for case P, 12.1 mW/C for case 2, 4.8 mW/C f

21、or cases H and X. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89615 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 4 DSCC FORM 2234 APR 97 1.5 Radiation features. Maximum total dos

22、e available (dose rate = 50 - 300 rads (Si)/s) 300 krads(Si) 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of the

23、se documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electro

24、nic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Des

25、k, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulat

26、ions unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modifi

27、cation in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.1.1 Microcircuit die. For the requirements of

28、microcircuit die, see appendix A to this document. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case

29、outline. The case outline shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth tables. The truth tables shall be as specified on figure 2. 3.2.4 Radiation test circuit. The radiation test circuit shall be mainta

30、ined by the manufacturer under document revision level control and shall be made available to the preparing and acquiring activity upon request. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89615 DLA LAND

31、AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 5 DSCC FORM 2234 APR 97 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified i

32、n table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the

33、PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA desi

34、gnator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“

35、 as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requi

36、rements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DLA Land and Maritime-VA prior to lis

37、ting as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certifi

38、cate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DLA Land and M

39、aritime-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DLA Land and Maritime, DLA Land and Maritime s agent, and the acquiring activity retai

40、n the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircui

41、t group number 53 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89615 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 6 DSCC FORM 2234 APR 97 TABLE I.

42、 Electrical performance characteristics. Test Symbol Conditions 1/ -55C TA +125C VCC= 5.5 V Group A subgroups Limits Unit unless otherwise specified Min Max Electrical characteristics for driver. Differential output voltage VOD1VCC= 5.5 V, IO= 0 A, VIN= 0.8 V 1, 2, 3 6 V M,D,P,L,R,F 1 VCC= 5.5 V, IO

43、= 0 A, VIN= 2.0 V 1, 2, 3 6 M,D,P,L,R,F 1 VOD2VCC= 4.5 V, RL= 100 1, 2, 3 2 M,D,P,L,R,F 1 VCC= 4.5 V, RL= 54 1, 2, 3 1.5 M,D,P,L,R,F 1 1.5VOD3VCC= -7 V to 12 V 1, 2, 3 1 M,D,P,L,R,F 1 Change in differential 2/ output voltage VODVCC= 4.5 V, RL= 100 1, 2, 3 200 mV M,D,P,L,R,F 1 200 VCC= 4.5 V, RL= 54

44、1,2,3 200 M,D,P,L,R,F 1 200Change in common 2/ mode output voltage VOCVCC= 4.5 V, RL= 100 1, 2, 3 200 mV M,D,P,L,R,F 1 200 VCC= 4.5 V, RL= 54 1,2,3 200 M,D,P,L,R,F 1 200See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-ST

45、ANDARD MICROCIRCUIT DRAWING SIZE A 5962-89615 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - continued. Test Symbol Conditions 1/ -55C TA +125C VCC= 5.5 V Group A subgroups Limits Unit unless otherwise

46、specified Min Max Electrical characteristics for driver - continued. Common mode output voltage VOCRL= 100 1, 2, 3 3 V M,D,P,L,R,F 1 3 RL= 54 1,2,3 3 M,D,P,L,R,F 1 Logical “1“ input current IIHVI= 2.4 V 1, 2, 3 20 A M,D,P,L,R,F 1 20Output current IOOutput disable, VOUT= 12 V 1, 2, 3 1 mA M,D,P,L,R,F

47、 1 Output disable, VOUT= 12 V, 1, 2, 3 1 VCC= 0 V M,D,P,L,R,F 1 1 Output disable, VOUT= -7 V 3/ 1, 2, 3 -0.8 M,D,P,L,R,F 1 -0.8 Output disable, VOUT= -7 V, 1,2,3 -0.8 VCC= 0 V M,D,P,L,R,F 1 -0.8 Output short circuit current IOSVIN= 3 V, VOUT= VCC1, 2, 3 150 mA M,D,P,L,R,F 1 150VIN= 0 V, VOUT= VCC1,2

48、,3 150 M,D,P,L,R,F 1 150VIN= 3 V, VOUT= -7 V 3/ 1,2,3 -250 M,D,P,L,R,F 1 -250See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89615 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 8 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - continued. Test Symbol Conditions 1/ -55C TA +125C VCC= 5.5 V Group A subgroups Lim