DLA SMD-5962-88517 REV C-2004 MICROCIRCUIT HYBRID LINEAR 14-BIT DIGITAL TO ANALOG CONVERTER《14位数位类比转换器混合动力线性微电路》.pdf

《DLA SMD-5962-88517 REV C-2004 MICROCIRCUIT HYBRID LINEAR 14-BIT DIGITAL TO ANALOG CONVERTER《14位数位类比转换器混合动力线性微电路》.pdf》由会员分享，可在线阅读，更多相关《DLA SMD-5962-88517 REV C-2004 MICROCIRCUIT HYBRID LINEAR 14-BIT DIGITAL TO ANALOG CONVERTER《14位数位类比转换器混合动力线性微电路》.pdf（13页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changed to reflect MIL-H-38534 processing. Editorial changes throughout. 91-04-23 W. Heckman B Paragraph 1.3, add note 1. Figure 1, case outline X and Y, convert dimensioning to symbol and inches/millimeters table. Update drawing boilerplate. 02-

2、12-13 Raymond Monnin C Rewrite paragraphs 4.2.a.2. and 4.3.3.b.2 to add TC. 04-04-23 Raymond Monnin THE ORIGINAL FIRST PAGE OF THIS DRAWING HAS BEEN REPLACED. REV SHEET REV SHEET REV STATUS REV C C C C C C C C C C C C OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 PMIC N/A PREPARED BY Donald R. Osborne

3、DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY Raymond Monnin POST OFFICE BOX 3990 COLUMBUS, OHIO 43216-5000 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Michael A. Frye MICROCIRCUIT, HYBRID, LINEAR, 14-BIT, DIGITAL TO ANALOG CONVER

4、TER AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 88-12-16 AMSC N/A REVISION LEVEL C SIZE A CAGE CODE 67268 5962-88517 SHEET 1 OF 12 DSCC FORM 2233 APR 97 5962-E200-04 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCI

5、RCUIT DRAWING SIZE A 5962-88517 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL C SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing describes device requirements for class H hybrid microcircuits to be processed in accordance with MIL-PRF-38534 and a choice of cas

6、e outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). 1.2 PIN. The PIN shall be as shown in the following example: 5962-88517 01 X X Drawing number Device type Case outline Lead finish (see 1.2.1) (see 1.2.2) (see 1.2.3) 1.2.1 Device type(s). The devic

7、e type(s) shall identify the circuit function as follows: Linearity Device type Generic number Circuit function error 01 DAC-02310-112 14-bit D/A converter, deglitched .012% FSR 02 DAC-02310-113 14-bit D/A converter, deglitched .006% FSR 1.2.2 Case outline(s). The case outline(s) shall be as designa

8、ted in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X See figure 1 32 Dual-in-line Y See figure 1 32 Flat package 1.2.3 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute maximum ratings. 1/ Positive supply voltage range (V

9、CC). -0.3 V dc to +18 V dc Negative supply voltage range (VEE) . +0.3 V dc to -18 V dc Logic supply voltage range (VDD) -0.3 V dc to +7.0 V dc Analog output current 10 mA Logic Input voltage -0.3 V dc to VDDPower dissipation (TC= +125C). 1.65 W Storage temperature range . -65C to +150C Lead temperat

10、ure (soldering, 10 seconds) +300C Junction temperature (TJ) +150C Thermal resistance, junction-to-case (JC): Cases X and Y . 13.2C/W Thermal resistance, junction-to-ambient (JA): Cases X and Y . 42C/W 1.4 Recommended operating conditions. Positive supply voltage range (VCC). +14.25 V dc to +15.75 V

11、dc Negative supply voltage range (VEE) . -14.25 V dc to -15.75 V dc Logic supply voltage range (VDD) +4.5 V dc to +5.5 V dc Logic Input voltage 0 V dc to +5.0 V dc Analog output current 5.0 mA maximum Case operating temperature range (TC) -55C to +125C 1/ Stresses above the absolute maximum rating m

12、ay cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88517 DEFENSE SUPPLY CENTER CO

13、LUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL C SHEET 3 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified

14、, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard fo

15、r Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or www.dodssp.daps.mil or from the Sta

16、ndardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, superse

17、des applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirements for device class H shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 may include the performance of all tests

18、herein or as designated in the device manufacturers Quality Management (QM) plan or as designated for the applicable device class. The manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as defined in MIL-PRF-38534 shall be met for th

19、e applicable device class. In addition, the modification in the QM plan shall not affect the form, fit, or function of the device for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-385

20、34 and herein. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.2 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.2.3 Block diagram. The block diagram shall be as specified on figure 3. 3.3 Electrical performanc

21、e characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full specified operating temperature range. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD

22、 MICROCIRCUIT DRAWING SIZE A 5962-88517 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL C SHEET 4 DSCC FORM 2234 APR 97 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are

23、defined in table I. 3.5 Marking of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers vendor similar PIN may also be marked. 3.6 Data. In addition to the general performance requireme

24、nts of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually

25、tested, and for those which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be made available to the preparing activity (DSCC-VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a man

26、ufacturer in order to supply to this drawing. The certificate of compliance (original copy) submitted to DSCC-VA shall affirm that the manufacturers product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL

27、-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified in the device manufacturers Quality Management (QM) plan. The modification i

28、n the QM plan shall not affect the form, fit, or function as described herein. 4.2 Screening. Screening shall be in accordance with MIL-PRF-38534. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be m

29、aintained by the manufacturer under document revision level control and shall be made available to either DSCC-VA or the acquiring activity upon request. Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in

30、 method 1015 of MIL-STD-883. (2) TAor TCas specified in the approved manufacturers QM plan. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. Provide

31、d by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88517 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL C SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Limits T

32、est Symbol Conditions -55C TC +125C unless otherwise specified Group A subgroups Device type Min Max Unit Positive supply current ICC+14.25 V VCC +15.75 V 1,2,3 All 50 mA Negative supply current IEE-14.25 V VEE -15.75 V 1,2,3 All -35 mA Logic supply current IDD+4.5 V VDD +5.5 V 1,2,3 All 45 mA 01 -0

33、.012 +0.012 1 02 -0.006 +0.006 01 -0.032 +0.032 2 02 -0.016 +0.016 01 -0.028 +0.028 Linearity error LEOutput range = 5.0 V 3 02 -0.014 +0.014 %FSR 01 -0.2 +0.2 4 02 -0.1 +0.1 01 -0.45 +0.45 5 02 -0.35 +0.35 01 -0.40 +0.40 Gain error 1/ AEOutput range = 5.0 V 6 02 -0.30 +0.30 %FSR 01 -20.0 +20.0 4 02

34、 -10.0 +10.0 01 -40.0 +40.0 5 02 -30.0 +30.0 01 -36.0 +36.0 Offset error 1/ OEOutput range = 5.0 V 6 02 -26.0 +26.0 mV See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88517 DEFE

35、NSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL C SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Limits Test Symbol Conditions -55C TC +125C unless otherwise specified Group A subgroups Device type Min Max Unit 01 -20.0 +20.0 4 02 -10.0

36、 +10.0 01 -70.0 +70.0 5 02 -60.0 +60.0 01 -60.0 +60.0 Pedestal error 1/ PEOutput range = 5.0 V 6 02 -50.0 +50.0 mV Settling time to 0.01% FSR ts10 V full scale change 9 All 1.8 s Slew rate SR Output range = 5.0 V 4 All 15.0 V/s Glitch voltage 2/ VG 3/ 4,5,6 All 30.0 mVp-p Reference output voltage VR

37、EFRL= 3.3 k 1,2,3 All -10.1 -9.9 V Analog output current IOOutput range = 5.0 V 1,2,3 All -5.0 +5.0 mA Analog output 2/ impedance ZOOutput range = 5.0 V 4,5,6 All 0.1 Digital input low voltage 2/ VIL1,2,3 All +0.8 V Digital input high voltage 2/ VIH1,2,3 All +2.0 V 1/ Gain, offset, and pedestal erro

38、rs are trimmable to zero using an external potentiometer adjustment circuit. Limits specified are without external potentiometer. 2/ Parameter shall be tested as part of device initial characterization and after design and process changes. Parameter shall be guaranteed to the limits specified in tab

39、le I for all lots not specifically tested. 3/ Glitch voltage is measured at 1.0 MHz update rate with a 5.0 MHz filter. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88517 DEFENSE SUPPLY CENTER COLUMBUS COLU

40、MBUS, OHIO 43216-5000 REVISION LEVEL C SHEET 7 DSCC FORM 2234 APR 97 Case outline X. Millimeters Inches Symbol Minimum Maximum Minimum Maximum A - 5.33 - .210 b 0.41 0.51 .016 .020 D 44.58 1.755 D1 37.97 38.23 1.495 1.505 E 29.34 1.155 e 2.54 BSC .100 BSC eA 22.73 22.99 .895 .905 L 4.57 - .180 - NOT

41、ES: 1. Pin numbers are for reference only. 2. The U.S. government preferred system of measurement is the metric SI. This case outline was designed using inch-pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule.

42、FIGURE 1. Case outline(s). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88517 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL C SHEET 8 DSCC FORM 2234 APR 97 Case outline Y. Millime

43、ters Inches Symbol Minimum Maximum Minimum Maximum A - 4.45 - .175 A1 1.52 1.78 .060 .070 b 0.31 0.46 .012 .018 c 0.20 0.31 .008 .012 D 45.72 1.800 D1 37.97 38.23 1.495 1.505 E 27.94 1.100 e 2.54 BSC .100 BSC L 12.70 - .500 - R 0.51 TYP .020 TYP S 3.48 3.99 .137 .157 NOTES: 1. Pin numbers are for re

44、ference only. 2. The U.S. government preferred system of measurement is the metric SI. This case outline was designed using inch-pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. FIGURE 1. Case outline(s). Pr

45、ovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88517 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL C SHEET 9 DSCC FORM 2234 APR 97 Device types All Case outlines X and Y Terminal numb

46、er Terminal symbol 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 (MSB) +5.0 V supply Feedback 3 +15 V supply Pedestal adjust Delay adjust Negative strobe out Strobe in Positive strobe out Sense Analog output -15

47、 V supply Bipolar Feedback 1 Feedback 2 Gain adjust Reference input Reference output Ground Bit 14 (LSB) Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 FIGURE 2. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING S

48、IZE A 5962-88517 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL C SHEET 10 DSCC FORM 2234 APR 97 FIGURE 3. Block diagram.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88517 DEFENSE SUPPLY CENTER COLUMBUS