DLA SMD-5962-87783 REV C-2011 MICROCIRCUIT LINEAR FOUR CHANNEL PROGRAMMABLE AMPLIFIER MONOLITHIC SILICON.pdf

《DLA SMD-5962-87783 REV C-2011 MICROCIRCUIT LINEAR FOUR CHANNEL PROGRAMMABLE AMPLIFIER MONOLITHIC SILICON.pdf》由会员分享，可在线阅读，更多相关《DLA SMD-5962-87783 REV C-2011 MICROCIRCUIT LINEAR FOUR CHANNEL PROGRAMMABLE AMPLIFIER MONOLITHIC SILICON.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes to input bias current and input offset current test conditions. Delete vendor CAGE 64762. Update boilerplate. lgt 97-10-15 R. MONNIN B Replaced reference to MIL-STD-973 with reference to MIL-PRF-38535. -rrp 04-01-27 R. MONNIN C Update dra

2、wing as part of 5 year review. - jt 11-01-18 C. SAFFLE THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED. REV SHEET REV SHEET REV STATUS REV C C C C C C C C C C C OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY CHARLES E. BESORE DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 h

3、ttp:/www.dscc.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY RAY MONNIN APPROVED BY MICHAEL A. FRYE MICROCIRCUIT, LINEAR, FOUR CHANNEL PROGRAMMABLE AMPLIFIER, MONOLITHIC SILICON DRAWING APPROVAL DATE 89-

4、07-20 AMSC N/A REVISION LEVEL C SIZE A CAGE CODE 67268 5962-87783 SHEET 1 OF 11 DSCC FORM 2233 APR 97 5962-E145-11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87783 DLA LAND AND MARITIME COLUMBUS, OHIO 43

5、218-3990 REVISION LEVEL C SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in th

6、e following example: 5962-87783 01 E X Drawing number Device type (see 1.2.1) Case outline (see 1.2.2) Lead finish (see 1.2.3) 1.2.1 Device type. The device type identify the circuit function as follows: Device type Generic number Circuit function 01 HA-2400 Four channel programmable amplifier 1.2.2

7、 Case outlines. The case outlines are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style E GDIP1-T16 or CDIP2-T16 16 Dual-in-line 2 CQCC1-N20 20 Square leadless chip carrier 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535,

8、appendix A. 1.3 Absolute maximum ratings. Voltage between +VCCand VCCterminals . +45 V dc Differential input voltage VCCOutput current (short-circuit protected) . 33 mA Storage temperature range . -65C to +150C Internal power dissipation (PD) 400 mW Lead temperature (soldering, 10 seconds) +275C The

9、rmal resistance, junction-to-case (JC): Cases E and 2 . See MIL-STD-1835 Thermal resistance, junction-to-ambient (JA): Case E . 91C/W Case 2 . 88C/W Junction temperature (TJ) +175C 1.4 Recommended operating conditions. Positive supply voltage (+VCC) +15 V dc Negative supply voltage (-VCC) -15 V dc A

10、mbient operating temperature range (TA) . -55C to +125C Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87783 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 3 DSCC FORM 2234 APR 97 2.

11、APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DE

12、PARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL

13、-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.

14、) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREME

15、NTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer Listing (QML) certified and qualified manufacturer o

16、r a manufacturer who has been granted transitional certification to MIL-PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) p

17、lan may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device. These modifications shall not affect the PIN as described herein. A “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 is required to identify when the QML

18、flow option is used. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A and herein. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.2 herein. 3.2.2 Terminal connections. The te

19、rminal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth table shall be as specified on figure 2. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the f

20、ull ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are described in table I. 3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The p

21、art shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. 3.5.1 Certificatio

22、n/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used.

23、Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87783 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 4 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbo

24、l Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Input offset voltage VIOVCM= 0 V 1 01 9.0 mV 2, 3 11 Input bias current +IIBVCM= 0 V, +RS= 10 k, -RS= 100 1 01 200 nA 2, 3 400 -IIBVCM= 0 V, +RS= 100 , -RS= 10 k 1 200 2, 3 400 Input offset cur

25、rent IIOVCM= 0 V, +RS= 10 k, -RS= 10 k 1 01 50 nA 2, 3 100 Common mode input voltage range +VCM+VCC= 6.0 V, -VCC= -24 V, VOUT= -9.0 V 1, 2, 3 01 9.0 V -VCM+VCC= +24 V, -VCC= -6.0 V, VOUT= 9.0 V -9.0 Large signal voltage gain AVVOUT= -10 V to +10 V, RL= 2 k 4 01 50 kV/V 5, 6 25 Common mode rejection

26、ratio +CMRR VCM= +5.0 V, +VCC= +10 V, -VCC= -20 V, VOUT= -5.0 V 1, 2, 3 01 80 dB -CMRR VCM= +5.0 V, +VCC= +20 V, -VCC= -10 V, VOUT= 5.0 V 80 Output voltage swing +VOUTRL= 2 k 4, 5, 6 01 10 V -VOUT-10 Output current +IOUTVOUT= 10 V, TA= +25C 4 01 10 mA -IOUTVOUT= -10 V, TA= +25C -10 Supply current +I

27、CCVOUT= 0 V 1 01 6.0 mA 2, 3 7.0 +ICC1 -6.0 2, 3 -7.0 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87783 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEE

28、T 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Power supply rejection ratio +PSRR1 +VCC= 20 V, -VCC= -15 V 1, 2, 3 01 74 dB +PSRR2 +VCC= 10 V, -V

29、CC= -15 V 74 -PSRR1 +VCC= 15 V, -VCC= -20 V 74 -PSRR2 +VCC= 15 V, -VCC= -10 V 74 Crosstalk CTVIN= 10 V, TA= +25C 1 01 -80 dB Digital input current IILVIL= 0 V 1, 2, 3 01 1.5 mA IIHVIH= 5.0 V 1.0 A Slew rate +SR1 VOUT= -5.0 V to +5.0 V, AV = +1, RL= 2.0 k, CL = 50 pF, CCOMP= 15 pF 7 01 6 V/s 8 5 -SR1

30、 VOUT= +5.0 V to -5.0 V, AV = +1, RL= 2.0 k, CL = 50 pF, CCOMP= 15 pF 7 6 8 5 Slew rate 2/ +SR2 VOUT= -5.0 V to +5.0 V, AV = +10, RL= 2.0 k, CL = 50 pF, CCOMP= 0 pF 7 01 20 V/s 8 17 -SR2 VOUT= +5.0 V to -5.0 V, AV = +10, RL= 2.0 k, CL = 50 pF, CCOMP= 0 pF 7 20 8 17 Rise time tr1VOUT= 0 to +200 mV, A

31、V= +1, RL= 2.0 k, CL = 50 pF, CCOMP= 15 pF 7 01 45 ns 8 55 tr2VOUT= 0 to +200 mV, 2/ AV= +10, RL= 2.0 k, CL = 50 pF, CCOMP= 0 pF 7 45 8 55 Fall time tf1VOUT= 0 to -200 mV, AV= +1, RL= 2.0 k, CL = 50 pF, CCOMP= 15 pF 7 01 45 ns 8 55 tf2VOUT= 0 to -200 mV, AV= +10, RL= 2.0 k, CL = 50 pF, CCOMP= 0 pF 7

32、 45 8 55 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87783 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical

33、 performance characteristics Continued. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Overshoot +OS1VOUT= 0 to +200 mV, AV= +1, RL= 2.0 k, CL = 50 pF, CCOMP= 15 pF 7 01 40 % 8 50 -OS1VOUT= 0 to -200 mV, AV= +1, RL= 2.0 k, CL = 50

34、 pF, CCOMP= 15 pF 7 40 8 50 +OS2VOUT= 0 to +200 mV, AV= +10, RL= 2.0 k, CL = 50 pF, CCOMP= 0 pF 2/ 7 40 8 50 -OS2VOUT= 0 to -200 mV, AV= +10, RL= 2.0 k, CL = 50 pF, CCOMP= 0 pF 2/ 7 40 8 50 Unity gain bandwidth 2/ UGBW AV= +1, RL= 2.0 k, CL= 50 pF, CCOMP= 15 pF, TA= +25C 4 01 4 MHz Gain bandwidth pr

35、oduct 2/ GBWP AV= +10, RL= 2.0 k, CL= 50 pF, CCOMP= 0 pF, TA= +25C 4 01 20 MHz Full power bandwidth 2/ 3/ FPBW1VO= 10 V, AV= +1, RL= 2.0 k, CL= 50 pF, CCOMP= 15 pF 4 01 95 kHz 5, 6 79 FPBW2VO= 10 V, AV= +10, RL= 2.0 k, CL= 50 pF, CCOMP= 0 pF 4 300 5, 6 270 See footnotes at end of table. Provided by

36、IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87783 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol

37、Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Settling time 2/ tSVENABLE= +5.0 V (or Decode Control), AV = +1, CCOMP= 15 pF, RL= 2.0 k, CL= 50 pF, VO= 10 VP-Pto 0.1% final value, TA= +25C 7 01 2.5 s Output delay 2/ td50% of Enable (or Decode

38、 Control) to 10% of output, VENABLE= +5.0 V (or Decode Control), TA= +25C 9 01 250 ns 1/ +VCC= +15 V, -VCC= -15 V, RS= 100 , RL= 500 k, and VOUT= 0 V, unless otherwise specified. Digital inputs: VIL= +0.5 and VIH= +2.4 V. Limits apply to each of the four channels, when addressed. See figure 2 herein

39、. 2/ Parameters shall be characterized at initial device design and after major process or design change which affects these parameters. Sample size = 15 minimum. 3/ Full power bandwidth = SR . 2V(pk) 3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in

40、 order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DLA Land and Maritime -VA prior to listing as an approved source of supply shall affirm that the manufacturers product meets the requirements of MIL-PRF-38535, appendix A

41、and the requirements herein. 3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change. Notification of change to DLA Land and Maritime -VA shall be requ

42、ired for any change that affects this drawing. 3.9 Verification and review. DLA Land and Maritime, DLA Land and Maritime s agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available on

43、shore at the option of the reviewer. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87783 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 8 DSCC FORM 2234 APR 97 Device type 01 Case ou

44、tlines E 2 Terminal number Terminal symbol 1 Input 3+ No connection 2 Input 3- Input 3+ 3 Input 4+ Input 3- 4 Input 4- Input 4+ 5 Input 1- Input 4- 6 Input 1+ No connection 7 Input 2- Input 1- 8 Input 2+ Input 1+ 9 -VCCInput 2- 10 Output Input 2+ 11 +VCCNo connection 12 COMP -VCC13 Ground Output 14

45、ENABLE +VCC15 D1COMP 16 D0No connection 17 - Ground 18 - ENABLE 19 - D120 - D0FIGURE 1. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87783 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3

46、990 REVISION LEVEL C SHEET 9 DSCC FORM 2234 APR 97 D1 D0 ENABLE Selected channel L L H 1 L H H 2 H L H 3 H H H 4 X X L None FIGURE 2. Truth table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87783 DLA LAN

47、D AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 10 DSCC FORM 2234 APR 97 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-

48、883, and shall be conducted on all devices prior to quality conformance inspection. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiri