DLA SMD-5962-03237 REV B-2012 MICROCIRCUIT LINEAR LOW DROPOUT ADJUSTABLE POSITIVE REGULATORS MONOLITHIC SILICON.pdf

《DLA SMD-5962-03237 REV B-2012 MICROCIRCUIT LINEAR LOW DROPOUT ADJUSTABLE POSITIVE REGULATORS MONOLITHIC SILICON.pdf》由会员分享，可在线阅读，更多相关《DLA SMD-5962-03237 REV B-2012 MICROCIRCUIT LINEAR LOW DROPOUT ADJUSTABLE POSITIVE REGULATORS MONOLITHIC SILICON.pdf（19页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes made to 1.2.2 and 1.3. Under table I, made changes to VREF, VRLOAD, ICTRL, IL, minimum VCONTROL, minimum VPOWER, and VREG. Drawing updated to reflect current requirements. -rrp 05-04-18 R. MONNIN B Update drawing as part of 5 year review.

2、 -jt 12-02-02 C. SAFFLE REV SHEET REV B B B B SHEET 15 16 17 18 REV STATUS REV B B B B B B B B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY RICK OFFICER DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil STANDARD MICROCIRCUIT DRAWIN

3、G THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY RAJESH PITHADIA APPROVED BY RAYMOND MONNIN MICROCIRCUIT, LINEAR, LOW DROPOUT, ADJUSTABLE POSITIVE REGULATORS, MONOLITHIC SILICON DRAWING APPROVAL DATE 03-11-25 AMSC N/A REVISION LEVEL B SIZE A

4、 CAGE CODE 67268 5962-03237 SHEET 1 OF 18 DSCC FORM 2233 APR 97 5962-E151-12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-03237 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 2 DSCC

5、 FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Numbe

6、r (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 03237 01 M M X Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2) Device class designator Case outline

7、(see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A spec

8、ified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device types. The device types identify the circuit function as follows: Device type Generic number Circuit function Output current 01 OM7580 Low dropout, adjustable positive regulator 7

9、 A 02 OM7581 Low dropout, adjustable positive regulator 8 A 03 OM7585A Low dropout, adjustable positive regulator 5 A 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Ven

10、dor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outlines. The case outlines are as designated in MIL-STD-1835 and as follows: Outl

11、ine letter Descriptive designator Terminals Package style M CBCC2-N3 3 Surface mount T MSFMI-P3 3 TO-257AA flange mount with isolated tab, glass sealed U See figure 1 3 SMD-257A flange mount, glass sealed X See figure 1 6 Power surface mount Y See figure 1 5 Flange mount with isolated tab with glass

12、 sealed Z See figure 1 6 Power surface mount 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICR

13、OCIRCUIT DRAWING SIZE A 5962-03237 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Output current (ILOAD): Device type 01 . 7 A Device type 02 . 8 A Device type 03 . 5 A Power input voltage (VIN) power: Device types 01 a

14、nd 02 . +6 V Power input voltage (VIN) control: Device types 01 and 02 . +13 V Power input voltage (VIN): Device type 03 . +7 V Power dissipation (PD): TC= +25C Device type 01 . 20 W Device type 02 . 20 W Device type 03, case M . 27.2 W Device type 03, cases T and U 26.5 W Operating junction tempera

15、ture range (TJ) . -55C to +125C Storage temperature range . -65C to +150C Lead temperature (TL) (soldering 10 seconds) . +300C Thermal resistance, junction to case (JC) Case outline M . 4.6C/W Case outlines T and U . 5.0C/W Case outline X . 5.0C/W Case outline Y . 5.0C/W Case outline Z . 5.0C/W 1.4

16、Recommended operating conditions. Output voltage range (VOUT) 1.8 V to 5.5 V Ambient operating temperature range (TA) . -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to t

17、he extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test

18、 Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. _ 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. Provided by IHSNot

19、for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-03237 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 4 DSCC FORM 2234 APR 97 DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit D

20、rawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of

21、a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual i

22、tem requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item

23、requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for

24、device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.3 Electrical performance characte

25、ristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electr

26、ical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire

27、 SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for d

28、evice class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, append

29、ix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manu

30、facturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DLA Land and Maritime-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device class

31、es Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appen

32、dix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DLA Land and Maritime -VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change t

33、hat affects this drawing. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-03237 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance c

34、haracteristics. Test Symbol Conditions -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Reference voltage VREFVCONTROL= 2.7 V, VPOWER= 2.0 V, VADJ= 0 V, ILOAD= 10 mA 1 01 1.243 1.257 V VCONTROL= 2.7 V to 12 V, VPOWER= 1.75 V to 5.5 V, ILOAD= 10 mA to 6 A, VA

35、DJ= 0 V 1,2,3 1.237 1.263 VCONTROL= 2.7 V, VPOWER= 2.05 V, VADJ= 0 V, ILOAD= 10 mA 1 02 1.243 1.257 VCONTROL= 2.7 V to 12 V, VPOWER= 2.75 V to 5.5 V, ILOAD= 10 mA to 8 A, VADJ= 0 V 1,2,3 1.237 1.263 VIN= 4.25 V, 1/ ILOAD= 10 mA 1 03 1.238 1.266 2.75 V VIN 7.0 V, 1/ ILOAD= 5.0 A 1,2,3 1.20 1.275 Line

36、 regulation VRLINEVCONTROL= 2.5 V to 12 V, VPOWER= 3 V to 5.5 V, ILOAD= 1.0 mA 1,2,3 01 3 mV VCONTROL= 2.5 V to 12 V, VPOWER= 1.75 V to 5.5 V, ILOAD= 10 mA 02 3 2.75 V VIN 7 V, 2/ ILOAD= 10 mA 03 8.5 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted

37、without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-03237 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions -55C TA +125C unless otherwise specified Group

38、 A subgroups Device type Limits Unit Min Max Load regulation VRLOADVCONTROL= 2.75 V, VPOWER= 2.1 V, ILOAD= 10 mA to 6 A 1,2,3 01 5 mV VCONTROL= 2.75 V, VPOWER= 2.75 V, ILOAD= 10 mA to 8 A 02 10 VIN= 4.25 V, 1/ 2/ 10 mA ILOAD 5 A, cases M and U 1 03 24 VIN= 4.25 V, case T, 1/ 2/ 10 mA ILOAD 5 A 17 VI

39、N= 4.25 V, 1/ 2/ 10 mA ILOAD 5 A, cases M and U 2,3 34 VIN= 4.25 V, case T, 1/ 2/ 10 mA ILOAD 5 A 24 Minimum load current ILMINVCONTROL= 5 V, 3/ VPOWER= 3.3 V, VADJ= 0 V 1,2,3 01,02 10 mA 2.75 V VIN 7.0 V 4/ 03 10 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or network

40、ing permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-03237 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions -55C TA +125C unless otherwise s

41、pecified Group A subgroups Device type Limits Unit Min Max Control pin current ICTRLVCONTROL= 2.75 V, 5/ VPOWER= 2.05 V, 1,2 01 120 mA ILOAD= 6 A 3 130 VCONTROL= 2.75 V, VPOWER= 2.75 V, ILOAD= 8 A 1,2,3 02 170 Adjust pin current IAVCONTROL= 2.75 V, VPOWER= 2.05 V, ILOAD= 10 mA, VADJ= 0 V 1 01 120 A

42、VCONTROL= 2.75 V, VPOWER= 2.05 V, ILOAD= 10 mA, VADJ= 0 V 1 02 120 VIN= 4.25 V, ILOAD= 10 mA 1,2,3 03 120 2.75 V VIN 7.0 V, 6/ 10 mA ILOAD 5.0 A 5.0 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT

43、DRAWING SIZE A 5962-03237 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 8 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Curren

44、t limit ILVCONTROL= 2.75 V, 1 01 7.1 A VPOWER= 2.05 V, VOUT= 100 mV 2,3 6.6 VCONTROL= 2.75 V, VPOWER=2.75 V, VOUT= 100 mV, TJ= +25C 1 02 8 VCONTROL= 2.75 V, VPOWER=2.75 V, VOUT= 100 mV, TJ= +125C, TJ= -55C 2,3 8 VIN= 6.75 V 1,2,3 03 5.0 Dropout voltage VDOVREF= 1 %, 7/ ILOAD= 5 A 1,2,3 03 1.4 V Quie

45、scent current IQVIN= 5 V 1,2,3 03 13 mA Minimum VCONTROLVPOWER= 3.3 V, ILOAD= 7 A 1,2 01 1.33 V VPOWER= 3.3 V, ILOAD= 6 A 3 1.35 VPOWER= 2.75 V, ILOAD= 8 A 1,2,3 02 1.35 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-S

46、TANDARD MICROCIRCUIT DRAWING SIZE A 5962-03237 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 9 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions -55C TA +125C unless otherwise specified Group A subgroups Device type Limit

47、s Unit Min Max Minimum VPOWERVCONTROL= 2.75 V, 1 01 0.62 V ILOAD= 7 A 2 0.80 VCONTROL= 2.75 V, ILOAD= 6 A 3 0.80 VCONTROL= 2.75 V, ILOAD= 8 A, TJ= +25C 1 02 0.85 VCONTROL= 2.75 V, ILOAD= 8 A, TJ= +125C 2 0.98 VCONTROL= 2.75 V, ILOAD= 8 A, TJ= -55C 3 0.98 Ripple rejection VIN/ VOUTVCONTROL= 5 V(AVG), VPOWER= 5 V(AVG), VRIPPLE= 1 VPP, ILOAD= 4 A, f = 120 Hz 4 01 60 dB VCONTROL= 5 V(AVG), VPOWER= 5 V(AVG), VRIPPLE= 1 VPP, fRIPPLE= 120 Hz, ILOAD= 4 A 02 60 VIN= 4.25 V, COUT= 100 F, f = 120 Hz, ILOAD= 5 A 4,5,6 03 60 200 See footnote