DLA MS39210 REV J-2012 NUTS TUBE COUPLING SAFETY SLEEVE COMPRESSION TYPE.pdf

《DLA MS39210 REV J-2012 NUTS TUBE COUPLING SAFETY SLEEVE COMPRESSION TYPE.pdf》由会员分享，可在线阅读，更多相关《DLA MS39210 REV J-2012 NUTS TUBE COUPLING SAFETY SLEEVE COMPRESSION TYPE.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、MS39210J 30 August 2012 SUPERSEDING MS39210H 29 March 2005 DETAIL SPECIFICATION SHEET NUTS, TUBE COUPLING SAFETY SLEEVE COMPRESSION TYPE This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein sh

2、all consist of this specification sheet. FIGURE 1. Nuts, tube coupling safety sleeve compression type. AMSC N/A FSC 4730 INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS39210J 2 Dash Number Tube OD A Thread B Thread Length (mm) C (mm) D

3、(mm) E (mm) F (mm) G (mm) 1 1/8 5/16 24UNF-2B .219 (5.56) .297 (7.54) .130 (3.30) .134(3.40) .438 (11.11) .275(6.99) .270(6.86) .438 (11.11) 2 3/16 3/8 24UNF-2B .219 (5.56) .297 (7.54) .190(4.83) .194(4.93) .438 (11.11) .338(8.59) .333(8.46) .500 (12.70) 3 1/4 1/2 20UNF-2B .281 (7.14) .359 (3.13) .2

4、55(6.48) .259(6.58) .563 (14.29) .454(11.53) .449(11.40) .625 (15.88) 4 5/16 9/16 18UNF-2B .281 (7.14) .390 (3.92) .318(8.08) .322(8.18) .578 (14.68) .512(13.00) .505(12.83) .688 (17.46) 5 3/8 5/8 18UNF-2B .313 (7.94) .422 (10.72) .380(9.65) .384(9.75) .625 (15.88) .575(14.61) .568(14.43) .750 (19.0

5、5) 6 1/2 3/4 16UNF-2B .328 (3.33) .453 (11.51) .506(12.85) .510(12.95) .688 (17.46) .693(17.60) .686(17.42) .875 (22.23) 7 5/8 15/16 16UN-2B .375 (9.53) .469 (11.91) .633(16.08) .637(16.18) .750 (19.05) .881(22.38) .874(22.20) 1.125 (28.58) 8 3/4 1-1/16 16UN-2B .406 (10.32) .500 (12.70) .758(19.25)

6、.762(19.35) .813 (20.64) 1.005(25.53) .999(25.37) 1.250 (31.75) 9 7/8 1-3/16 16UN-2B .406 (10.32) .500 (12.70) .883(22.43) .887(22.53) .813 (20.64) 1.131(28.73) 1.124(28.55) 1.375 (34.93) 10 1 1-5/16 16UN-2B .406 (10.32) .500 (12.70) 1.008(25.60) 1.012(25.70) .813 (20.64) 1.256(31.90) 1.249(31.72) 1

7、.500 (38.10) 11 1-1/4 1-5/8 16UN-2B .406 (10.32) .578 (14.68) 1.206(30.63) 1.264(32.11) .844 (31.43) 1.568(39.83) 1.561(39.65) 2 (50.80) 12 1-1/2 1-7/8 16UN-2B .500 (12.70) .672 (17.07) 1.510(38.35) 1.514(38.46) .969 (34.61) 1.818(46.18) 1.810(45.97) 2.250 (57.15) NOTES: 1. Dimensions are in inches,

8、 unless otherwise specified. Millimeters are in parentheses. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, the tolerance for 3 place decimals is decimals .005, the tolerance for fractions is 1/64, the tolerance for degrees is 2. 4. Threads shall be in a

9、ccordance with FED-STD-H28. 5. Referenced documents shall be of the issue in effect in date of invitations for bid. 6. This illustration is for identification and is not intended to restrict designs or shapes not dimensioned. FIGURE 1. Nuts, tube coupling safety sleeve compression type Continued. Pr

10、ovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS39210J 3 REQUIREMENTS: Dimensions and configuration: See figure 1. Tolerances: Unless otherwise specified, decimals .005, fractions 1/64, degrees 2. Threads: The threads shall be in accordance with FED-

11、STD-H28. Material: Code Material C Steel bar, type AISI-C-1112, C-1113, C-1117, C-1118 or C-1137 in accordance with SAE-AIR4127 F Alloy steel: in accordance with SAE-AIR4127 S Corrosion resistant steel in accordance with SAE AMS5659, SAE AMS5862 or, alloy 15-5 PH in accordance with ASTM A564/A564M t

12、ype XM-12 or UNS S15500, or SAE AMS5665 Chemical Finish: Code Finish C Carbon steel: Cadmium in accordance with SAE-AMS-QQ-P-416, type II, class 3, 200 inches to 300 inches (5.08 m to 7.62 m) thick. F Alloy steel: Cadmium in accordance with SAE-AMS-QQ-P-416, type II, class 3, 200 inches to 300 inche

13、s (5.08 m to 7.62 m) thick. S Corrosion resistant steel: Passivate in accordance with SAE AMS2700, type 6 or 7. Z Steel, chem finish alternativel: ASTM B633, type VI, FeZn 25. Part or Identifying Number (PIN) example: (PIN covers the complete item with nuts and sleeves.) Guidance on use of alternati

14、ve parts with less hazardous or non-hazardous materials. This specification provides an alternate material, corrosion resistant steel, and Zinc finish via the PIN. Users should select the PIN with the least hazardous material that meets the form, fit, and function requirements of their application.

15、MS 27612 -8 C Z If finish code same as Material code, then use only one code. Material code Dash size Specification number MS prefix Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS39210J 4 Changes from previous issue. The margins of this specifica

16、tion are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this

17、document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Referenced documents: This document references the following: FED-STD-H28 SAE AMS 5665 ASTM A564/A564M SAE AMS5862 ASTM B633 SAE AMS2700 SAE-AIR4127 SAE-AMS-QQ-P-416 SAE AMS5659 C

18、ONCLUDING MATERIAL Custodians: Preparing activity: Army AT DLA-CC Navy-YD Air Force-99 DLA - CC (Project 4730-2012-041) Review activities: Army AR Navy-SA, MC Air Force-71 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-