DLA MS39202 REV G-2012 ELBOWS PIPE TO TUBE SAFETY SLEEVE COMPRESSION TYPE 90 DEGREE MALE PIPE END.pdf

《DLA MS39202 REV G-2012 ELBOWS PIPE TO TUBE SAFETY SLEEVE COMPRESSION TYPE 90 DEGREE MALE PIPE END.pdf》由会员分享，可在线阅读，更多相关《DLA MS39202 REV G-2012 ELBOWS PIPE TO TUBE SAFETY SLEEVE COMPRESSION TYPE 90 DEGREE MALE PIPE END.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 4730 MS39202G 30 August 2012 SUPERSEDING MS39202F 1 February 2002 DETAIL SPECIFICATION SHEET ELBOWS, PIPE TO TUBE SAFETY SLEEVE COMPRESSION TYPE, 90 DEGREE, MALE PIPE END This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirement

2、s for acquiring the product described herein shall consist of this specification sheet. FIGURE 1. Elbows, pipe to tube safety sleeve compression type, 90 degree, male pipe end. Inactive for new design after 29 December 1967. INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permi

3、tted without license from IHS-,-,-MS39202G 2 TABLE I. Elbows, pipe to tube-safety sleeve compression type, 90 degree, male pipe end. 1/ 2/ Dash No. Tube O.D. A Pipe Thread NPTF B C Thread Length D E F G H 1 1/8 1/8 5/16 24UNF-2A 9/32 3/32 .135 .139 13/64 1/8 3/16 2 3/16 1/8 3/8 24UNF-2A 9/32 1/8 .19

4、6 .200 1/4 5/32 3/16 3 1/4 1/8 1/2 20UNF-2A 13/32 13/64 .261 .265 19/64 13/64 3/16 4 5/16 1/8 9/16 18UNF-2A 13/32 13/64 .324 .328 19/64 13/64 3/16 5 1/4 1/4 1/2 20UNF-2A 13/32 13/64 .261 .265 19/64 13/64 9/32 6 3/8 1/4 5/8 18UNF-2A 7/16 9/32 .386 .390 19/64 13/64 9/32 7 3/8 3/8 5/8 18UNF-2A 7/16 9/3

5、2 .386 .390 19/64 13/64 27/64 8 1/2 3/8 3/4 16UNF-2A 7/16 27/64 .514 .518 5/16 13/64 27/64 9 5/8 3/8 15/16 16UN-2A 15/32 1/2 .641 .645 11/32 15/64 27/64 10 3/8 1/2 5/8 18UNF-2A 7/16 9/32 .386 .390 19/64 13/64 7/16 11 1/2 1/2 3/4 16UNF-2A 7/16 27/64 .541 .518 5/16 13/64 7/16 12 5/8 1/2 15/16 16UN-2A

6、15/32 1/2 .641 .645 11/32 15/64 1/2 13 3/4 1/2 1-1/16 16UN-2A 15/32 21/32 .766 .770 11/32 13/64 1/2 14 3/4 3/4 1-1/16 16UN-2A 15/32 21/32 .766 .770 11/32 13/64 23/32 15 7/8 3/4 1-3/16 16UN-2A 15/32 23/32 .891 .895 11/32 13/64 21/32 16 1 3/4 1-5/16 16.UN-2A 15/32 7/8 1.016 1.020 13/32 13/64 23/32 17

7、7/8 1 1-3/16 16UN-2A 15/32 23/32 .891 .895 11/32 13/64 7/8 18 1 1 1-5/16 16UN-2A 15/32 7/8 1.016 1.020 13/32 13/64 7/8 19 1-1/4 1 1-5/8 16UN-2A 35/64 1-3/32 1.270 1.274 13/32 13/64 7/8 20 1-1/4 1-1/4 1-5/8 16UN-2A 17/32 1-3/32 1.270 1.274 13/32 13/64 1-1/8 21 1-1/2 1-1/2 1-7/8 16UN-2A 9/16 1-11/32 1

8、.520 1.524 15/32 13/64 1-11/32 See notes at end of tables. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS39202G 3 TABLE I. Elbows, pipe to tube-safety sleeve compression type, 90 degree, male pipe end Continued. 1/ 2/ K L M 3/4 21/32 31/32 3/4 21

9、/32 1 25/32 3/4 1-5/32 25/32 13/16 1-3/16 1-1/16 7/8 1-9/32 1-1/16 15/16 1-3/8 1-3/16 1-1/8 1-9/16 1-3/16 1-1/8 1-21/32 1-3/16 1-5/16 1-27/32 1-7/16 1-1/8 1-9/16 1-1/4 1-3/16 1-23/32 1-7/16 1-5/16 1-27/32 1-9/16 1-1/2 2-3/32 1-9/16 1-1/2 2-3/32 1-3/4 1-3/4 2-11/32 1-3/4 1-3/4 2-11/32 1-15/16 1-3/4 2

10、-11/32 1-15/16 1-3/4 2-11/32 1-5/16 2-1/4 2-7/8 2-5/16 2-1/4 2-7/8 2-9/16 2-3/8 3-1/16 1/ Dimensions are in inches. 2/ This illustration is for identification and is not intended to restrict designs or shapes not dimensioned. REQUIREMENTS: Dimensions and configuration: See figure 1. Tolerances: Unle

11、ss otherwise specified, decimals .005, fractions 1/64, degrees 2. Threads: The threads shall be in accordance with FED-STD-H28. Elbows. See table I. Material: Code Material C Steel bar, type AISI-C-1112, C-1113, C-1117, C-1118 or C-1137 in accordance with SAE AIR4127. F Alloy steel, in accordance wi

12、th SAE AIR4127. S Corrosion resistant steel in accordance with SAE AMS5659, SAE AMS5862, or, alloy 15-5 PH in accordance with ASTM A564/A564M type XM-12 or UNS S15500, or SAE AMS5665. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS39202G 4 Chemica

13、l finish: Code Finish C Carbon steel: Cadmium in accordance with SAE-AMS-QQ-P-416, type II, class 3, 200 inches to 300 inches (5.08 m to 7.62 m) thick. F Alloy: Cadmium in accordance with SAE-AMS-QQ-P-416, type II, class 3, 200 inches to 300 inches (5.08 m to 7.62 m) thick. S Corrosion resistant ste

14、el: Passivate in accordance with SAE AMS2700, type 6 or 7. Z Steel, alternative chem finish: ASTM B633 type VI, FeZn 25. Part or Identifying Number (PIN) example: (PIN covers the complete item with nuts and sleeves.) Guidance on use of alternative parts with less hazardous or non-hazardous materials

15、. This specification provides an alternate material, corrosion resistant steel, and Zinc finish via the PIN. Users should select the PIN with the least hazardous material that meets the form, fit, and function requirements of their application. Changes from previous issue. The margins of this specif

16、ication are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of th

17、is document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Referenced documents. This document reference the following: FED-STD-H28 SAE AMS5665 ASTM A564/A564M SAE AMS5862 ASTM B633 SAE AMS2700 SAE AIR4127 SAE-AMS-QQ-P-416 SAE AMS5659

18、MS39212 MS39210 MS 27612 -8 C Z If finish code same as Material code, then use only one code. Material code Dash size Specification number MS prefix Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS39202G 5 CONCLUDING MATERIAL Custodians: Preparing

19、activity: Army AT DLA - CC Navy-AS Air Force-99 (Project 4730-2012-038) DLA - CC Review activities: Army-AR Navy-MC,SA Air Force-71 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-