DLA MS27228 REV B-2007 FLANGE ASSEMBLY 90 ADAPTER HOSE TO TUBE REUSABLE HYDRAULIC FUEL AND OIL LINES《可重复使用的90度法兰软管组件适配器》.pdf

《DLA MS27228 REV B-2007 FLANGE ASSEMBLY 90 ADAPTER HOSE TO TUBE REUSABLE HYDRAULIC FUEL AND OIL LINES《可重复使用的90度法兰软管组件适配器》.pdf》由会员分享，可在线阅读，更多相关《DLA MS27228 REV B-2007 FLANGE ASSEMBLY 90 ADAPTER HOSE TO TUBE REUSABLE HYDRAULIC FUEL AND OIL LINES《可重复使用的90度法兰软管组件适配器》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 INCH-POUNDMS27228B 14 May 2007 SUPERSEDING MS27228A 22 September 2000 DETAIL SPECIFICATION SHEET FLANGE ASSEMBLY 90, ADAPTER, HOSE TO TUBE, REUSABLE, HYDRAULIC, FUEL AND OIL LINES This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements f

2、or acquiring the product described herein shall consist of this specification sheet and MIL-DTL-5070. FIGURE 1. 90 flange assembly dimensions and configuration. AMSC N/A Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-FSC 4730 MS27228B 2 Flange PIN (

3、see note 4) Nipple assembly PIN Socket PIN Dash number (see note 3) MS20756 MS27227 MS24590 -8 -8 -8 -8-10 -10 -10 -10 -12 -12 -12 -12MS24591-16 -16 -16 -16 -20 -20 -20 -20-24 -24 -24 -24 -32 -32 -32 -32-40 -40 -40 -40 -48 -48 -48 -48NOTES: 1. Dimensions are in inches. 2. Metric equivalents are give

4、n for information only. 3. All components of this assembly shall be aluminum alloys only. 4. Part or Identifying Number (PIN) FIGURE 1. 90 flange assembly dimensions and configuration - Continued. REQUIREMENTS: Dimensions and configurations: The design, construction, and physical dimensions shall be

5、 in accordance with MIL-DTL-5070 and figure 1 in case of conflict between this drawing and MIL-DTL-5070, this drawing shall govern. Intended use. This assembly is designed for use only with hose conforming to MIL-DTL-8794. This assembly is intended for use only in fuel and oil lines. Material: Alumi

6、num shall be in accordance with MIL-DTL-5070. Finish: Finish shall be in accordance with MIL-DTL-5070. Color identification: Color identification shall be accordance with MIL-DTL-5070. PIN example: MS 27228 -16 AA Material/finish code, see table I Dash number on figure 1 Specification number MS pref

7、ix Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27228B 3 TABLE I. Code for material and finish. Code Dash size Material/finish AA -8 through -48 Aluminum anodic coating Identification of product. The PIN and the manufacturers Commercial and Gove

8、rnment Entity (CAGE) Code or trademark shall be marked on a removable tag securely attached to the assembly. Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue, due to the extent of the changes. Referenced documents. I

9、n addition to MIL-DTL-5070, this document references the following: MIL-DTL-8794 MS20756 MS24590 MS24591 MS27227 CONCLUDING MATERIAL Custodians: Preparing activity: Army - AT DLA - CC Navy - AS Air Force - 99 (Project 4730-2005-047) DLA - CC Review activities: Army - AV Navy - MC, SA Air Force - 11,

10、 71 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-