DLA MS27226 REV B-2007 SWIVEL NUT ASSEMBLY 45 DEGREE ADAPTER HOSE TO TUBE REUSABLE HYDRAULIC FUEL AND OIL LINES《可重复使用的45度旋转螺母法兰软管组件适配器》.pdf

《DLA MS27226 REV B-2007 SWIVEL NUT ASSEMBLY 45 DEGREE ADAPTER HOSE TO TUBE REUSABLE HYDRAULIC FUEL AND OIL LINES《可重复使用的45度旋转螺母法兰软管组件适配器》.pdf》由会员分享，可在线阅读，更多相关《DLA MS27226 REV B-2007 SWIVEL NUT ASSEMBLY 45 DEGREE ADAPTER HOSE TO TUBE REUSABLE HYDRAULIC FUEL AND OIL LINES《可重复使用的45度旋转螺母法兰软管组件适配器》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 MS27226B INCH-POUND14 May 2007 SUPERSEDING MS27226A 22 September 2000 DETAIL SPECIFICATION SHEET SWIVEL NUT ASSEMBLY 45, ADAPTER, HOSE TO TUBE, REUSABLE, HYDRAULIC, FUEL AND OIL LINES This specification is approved for use by all Departments and Agencies of the Department of Defense. The requiremen

2、ts for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-5070. FIGURE 1. 45 Swivel nut assembly dimensions and configuration. AMSC N/A FSC 4730Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27226B 2 Nippl

3、e assembly PIN (see note 3) Socket PIN Dash numberMS27225 MS24590 -4 -4 -4-5 -5 -5 -6 -6 -6-8 -8 -8 -10 -10 -10-12 -12 -12 MS24591-16 -16 -16 -20 -20 -20-24 -24 -24 -32 -32 -32NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Part or Identifying Number (PIN

4、). FIGURE 1. 45 Swivel nut assembly dimensions and configuration - Continued. REQUIREMENTS: Dimensions and configurations: The design, construction, and physical dimensions shall be in accordance with MIL-DTL-5070 and figure 1 in case of conflict between this drawing and MIL-DTL-5070, this drawing s

5、hall govern. Intended use. This assembly is designed for use only with hose conforming to MIL-DTL-8794. PIN example: MS 27226 -4 CZ Material/finish designator see table I Dash number on figure 1 Specification number MS prefix Identification of product. The PIN and the manufacturers Commercial and Go

6、vernment Entity (CAGE) Code or trademark shall be marked on a removable tag securely attached to the assembly. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27226B 3 TABLE I. Code for material and finish. Code Dash size Material/finish CC -4 thro

7、ugh -6 Carbon Steel - cadmium plating CZ -4 through -6 Carbon steel - zinc plating SS -4 through -6 Corrosion resistant steel - N/A AA -8 through -32 Aluminum - anodic coating TA -4 through -32 Titanium - anodized or fluoride phosphated. To the users of this document, it is recommended that the use

8、of carbon steel material with cadmium plating be used only when the other materials and finishes specified in this document cannot meet performance requirements. Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue, due

9、to the extent of the changes. Referenced documents. In addition to MIL-DTL-5070, this document references the following: MIL-DTL-8794 MS27225 MS24590 MS24591 CONCLUDING MATERIAL Custodians: Preparing activity: Army - AT DLA - CC Navy - AS Air Force - 99 (Project 4730-2005-045) DLA - CC Review activi

10、ties: Army - AV Navy - MC, SA Air Force - 11, 71 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-