DLA MS27053 REV E-2013 ADAPTER ASSEMBLY FLARED STRAIGHT TUBE TO HOSE - WITH SWIVEL NUT.pdf
《DLA MS27053 REV E-2013 ADAPTER ASSEMBLY FLARED STRAIGHT TUBE TO HOSE - WITH SWIVEL NUT.pdf》由会员分享,可在线阅读,更多相关《DLA MS27053 REV E-2013 ADAPTER ASSEMBLY FLARED STRAIGHT TUBE TO HOSE - WITH SWIVEL NUT.pdf(5页珍藏版)》请在麦多课文档分享上搜索。
1、AMSC N/A FSC 4730 MS27053E 14 March 2013 SUPERSEDING MS27053D 25 September 2003 DETAIL SPECIFICATION SHEET ADAPTER ASSEMBLY, FLARED, STRAIGHT, TUBE TO HOSE - WITH SWIVEL NUT This specification sheet is approved for use by all Departments and Agencies of the Department of Defense. The requirements fo
2、r acquiring the product described herein shall consist of this specification sheet and MIL-DTL-27272. NOTES: 1. Dimension A, see table II, is the dimension between the hose end of the adapter and the free end of the insert at its centerline when the socket is assembled on the nipple subassembly. 2.
3、Lockwire holes if required in accordance with SAE-AS1043. 3. Socket may be hex or 2-flat-sides. FIGURE 1. Adapter assembly illustration. INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27053E 2 REQUIREMENTS: Intended use. This adapter is
4、 intended for use only with hose in accordance with MIL-DTL-27267. Materials. Material and material codes see table I. See applicable specification sheet and MIL-DTL-27272 for material of other components identified in table II for their material requirements. TABLE I. Materials and material codes.
5、Material code Material Blank Combination of aluminum alloy and corrosion-resistant steel (CRES) C CRES TABLE II. Adapter assembly composition. 1/ 2/ Size and material code Nipple subassembly size and material code Sleeve size and material code Socket size and material code Amax inch (mm) MS27061 3/M
6、S27070 3/MS27069 3/-3/-4C 4/ -3/4C -4C -4C 1.33 (33.78) -4C -4C 1.35 (34.29) -5C -5C -5C -5C 1.41 (35.81) -6C -6C -6C -6C 1.47 (37.34) -8C -8C -8C -8C 1.70 (43.18) -8 -8 -10C -10C -10C -10C 1.86 (47.24) -10 -10 -12C -12C -12C -12C 1.93 (49.02) -12 -12 -16C -16C -16C -16C 2.15 (54.61) -16 -16 -20C -2
7、0C -20C -20C 2.52 (64.01) -20 -20 -24C -24C -24C -24C 2.71 (68.83) -24 -24 1/ Dimensions are in inches. 2/ Metric equivalents are given for general information only. 3/ MS27061, MS27069 and MS27070 shall be dry film lubricated in accordance with table III, dry film is applied in accordance with MS27
8、061, MS27069 and MS27070 as applicable. 4/ Swivel nut and sealing surface of this nipple subassembly shall mate with SAE-AS4395-3 fitting. The remaining portion of the subassembly is to mate with M27267-4 hose. If required, lockwire holes to be drilled in accordance with SAE-AS1043 and suffix L adde
9、d to Part or Identifying Number (PIN). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27053E 3 Threads on -3/-4C through -24C shall be lubricated with dry-film lubricant in accordance with table III no overspray allowed. MS27061, MS27069 and MS270
10、70 parts shall be coated with the same type of dry film lubricant as indicated in the PIN, no mixing of dry film lubricants shall be used on an assembly unless it is of the types specified by the “blank” designator. NOTE: Avoid using graphite dry film lubes with aluminum nipples because in a wet env
11、ironment, graphite becomes corrosive to the aluminum. TABLE III. Dry film designator. Dry film designator SAE class or type designator Dry film characteristics Blank Any SAE class or type below N/A SAE-AS1701 SAE-AS1701 class SAE-AS1701 temperature ranges F (C) 4 4 -65 to +1400F (-54 to 760C) 5 5 -6
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- DLAMS27053REVE2013ADAPTERASSEMBLYFLAREDSTRAIGHTTUBETOHOSEWITHSWIVELNUTPDF

链接地址:http://www.mydoc123.com/p-696608.html