DLA MS24287 REV D-2005 MATED ASSEMBLY CONNECTOR RACK AND PANEL MINIATURE《微型机架和小组电器连接器成对装配》.pdf

《DLA MS24287 REV D-2005 MATED ASSEMBLY CONNECTOR RACK AND PANEL MINIATURE《微型机架和小组电器连接器成对装配》.pdf》由会员分享，可在线阅读，更多相关《DLA MS24287 REV D-2005 MATED ASSEMBLY CONNECTOR RACK AND PANEL MINIATURE《微型机架和小组电器连接器成对装配》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、INCH-POUNDMS24287D 14 July 2005 SUPERSEDING MS24287C 15 June 1965 This specification is approved for use by all DeparThe requirements for acquiring the product described hereiMIL-DTL-26518. The Qualified Products List (QPL) associated with maintained until acquisition of the product is no longerbe c

2、anceled. AMSC N/A Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DETAIL SPECIFICATION SHEET MATED ASSEMBLY, CONNECTOR RACK AND PANEL, MINIATURE tments and Agencies of the Department of Defense. n shall consist of this specification sheet and this in

3、active for new design specification will be required, where upon the specification and QPL will Inactive for new design after 8 June 1999. FIGURE 1. Connector mating and mounting details. FSC 5935 MS24287D 2 Shell size Dimension A B C D 3.875 2.445 2.000 E 3.454 2.025 1.580 F 3.388 1.959 1.528 G 3.3

4、75 1.945 1.516 Inches mm Inches mm .002 .043 .097 .125 .146 .210 .243 .530 .562 .639 1.015 0.05 1.09 2.46 3.18 3.71 5.33 6.17 13.46 14.27 17.60 25.78 1.081 1.516 1.528 1.580 1.945 1.959 2.000 2.025 3.375 3.388 3.454 3.875 27.46 38.51 38.81 40.13 49.40 49.53 50.80 51.44 85.73 86.06 87.73 98.43 Mating

5、 and mounting details of MS24285R, MS24286R, and MS27399 connectors for service or test. NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified tolerances are .005 inch (0.13 mm). FIGURE 1. Connector mating and mounting details - Conti

6、nued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS24287D 3 Shell size Dimension A B C D 3.875 2.445 2.000 E 3.454 2.025 1.580 F 3.388 1.959 1.528 G 3.375 1.945 1.516 FIGURE 2. Connector mating and mounting details Continued. Provided by IHSNot

7、for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS24287D 4 Inches mm Inches mm .002 .043 .097 .125 .146 .210 .562 .639 1.015 1.081 1.516 0.05 1.09 2.46 3.18 3.71 5.33 14.27 17.60 25.78 27.46 38.51 1.528 1.580 1.945 1.959 2.000 2.025 2.445 3.375 3.388 3.454 3.875 38.81

8、40.13 49.40 49.53 50.80 51.44 62.10 85.73 86.06 87.73 98.43 Mating and mounting details of MS24285R, MS24286H, and MS27399 connectors for service or test. NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified tolerances are .005 inch

9、(0.13 mm). FIGURE 2. Connector mating and mounting details. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS24287D 5 REQUIREMENTS: Dimensions and configuration see figure 1. This is a design specification. Not to be used a part number. Part or Iden

10、tifying Number (PIN): N/A Referenced documents: In addition to MIL-DTL-26518 this document references the following: MS24285 MS24286 MS24695 MS24700 MS27399 NASM24693 Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue

11、due to the extent of the changes. CONCLUDING MATERIAL Custodians: Preparing activity: Air Force - 11 DLA - CC DLA - CC (Project 5935-4700-000) Review activities: DLA - IS NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-