DLA MS17350 REV F-2013 COVER PROTECTIVE ELECTRICAL CONNECTOR PLUG.pdf

《DLA MS17350 REV F-2013 COVER PROTECTIVE ELECTRICAL CONNECTOR PLUG.pdf》由会员分享，可在线阅读，更多相关《DLA MS17350 REV F-2013 COVER PROTECTIVE ELECTRICAL CONNECTOR PLUG.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、 DETAIL SPECIFICATION SHEET COVER, PROTECTIVE, ELECTRICAL CONNECTOR, PLUG This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-22992. FIGU

2、RE 1. Dimensions and configuration. AMSC N/A FSC 5935 MS17350F 12 March 2013 SUPERSEDING MS17350E 07 March 2007 INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS17350F 2 NOTES: 1. All dimensions are in inches. 2. Metric equivalents are gi

3、ven for information only. 3. Unless otherwise specified, tolerances are .016 inch (0.41 mm). 4. F clearance to accommodate screw size indicated. 5. All dimensions apply after plating. FIGURE 1. Dimensions and configuration - Continued. Shell size A Thread class 2A Q (approx.) F clearance (see note 4

4、) 12 0.8750-0.1P-0.2L-DS 5.00 6 14 1.0000-0.1P-0.2L-DS 16 1.1250-0.1P-0.2L-DS 18 1.2500-0.1P-0.2L-DS 8 20 1.3750-0.1P-0.2L-DS 22 1.5000-0.1P-0.2L-DS 6.00 24 1.7500-0.1P-0.2L-DS 28 2.0000-0.1P-0.2L-DS 32 2.2500-0.1P-0.2L-DS 10 36 2.5000-0.1P-0.2L-DS 40 2.7500-0.1P-0.2L-DS 44 3.0000-0.1P-0.2L-DS Inche

5、s mm Inches mm .8750 1.0000 1.1250 1.2500 1.3750 1.5000 1.500 1.7500 22.225 25.400 28.575 31.750 34.925 38.100 38.10 44.45 2.0000 2.2500 2.5000 2.7500 3.0000 5.00 6.00 50.800 57.150 63.500 69.850 76.200 127.00 152.40 Provided by IHSNot for ResaleNo reproduction or networking permitted without licens

6、e from IHS-,-,-MS17350F 3 REQUIREMENTS: Design and construction: See figure 1. Chain shall be passivated stainless steel in accordance with type II, class 3, trade number 8, as specified in RR-C-271. Chain shall be within one link of length specified. Cover mates with MS17344. Cover finish shall be

7、in accordance with MIL-DTL-22992. Chain shall move freely on protective cap after assembly. Full part number marking shall be in accordance with MIL-DTL-22992, and shall include the “JAN brand” (JAN or J) certification marking. Part or Identifying Number (PIN) example: MS17350 N 28 MS number Finish

8、Size Qualification: Visual and mechanical examination. Magnetic permeability. Water immersion (with protective cover). Salt spray (corrosion). Tensile. Air leakage. Group A sampling plan: Lot and sample sizes shall be as specified in table I. Samples shall be randomly selected from the lot. If one o

9、r more defects are found, the lot shall be rescreened and defects removed. A new sample as specified in table I shall then be randomly selected. If one or more defects are found in the second sample lot, the lot shall not be supplied to this specification. TABLE I. Group A sampling plan. Lot size Sa

10、mpling size 1 to 13 100 percent 14 to 150 13 units 151 to 280 20 units 281 to 500 29 units 501 to 1,200 34 units 1,201 to 3.200 42 units Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS17350F 4 Changes from previous issue. Marginal notations are no

11、t used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Referenced documents. In addition to MIL-DTL-22992, this document references the following: MS17344 RR-C-271 CONCLUDING MATERIAL Custodians: Preparing activity: Army CR DLA CC Navy EC Air

12、 Force 85 DLA CC Review activities: (Project 59352012186) Army AR, CR4, MI Navy AS, CG, MC, OS Air Force 19 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-