DLA MS17343 REV G-2013 CONNECTOR RECEPTACLE ELECTRICAL WALL MOUNTING.pdf

《DLA MS17343 REV G-2013 CONNECTOR RECEPTACLE ELECTRICAL WALL MOUNTING.pdf》由会员分享，可在线阅读，更多相关《DLA MS17343 REV G-2013 CONNECTOR RECEPTACLE ELECTRICAL WALL MOUNTING.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、 DETAIL SPECIFICATION SHEET CONNECTOR, RECEPTACLE, ELECTRICAL, WALL MOUNTING This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-22992. F

2、IGURE 1. Dimensions and configuration. AMSC N/A FSC 5935 MS17343G 16 January 2013 SUPERSEDING MS17343F 26 October 2005 INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS17343G 2 FIGURE 1. Dimensions and configuration - Continued. Provided

3、by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS17343G 3 Shell size A Thread (plated) class 2A D dia + .005 - .010 K + .005 - .020 L .020 12 0.8750-0.1P-0.2L-DS .567 .938 .640 14 1.0000-0.1P-0.2L-DS .692 .938 .640 16 1.1250-0.1P-0.2L-DS .817 .938 .640 18 1.

4、2500-0.1P-0.2L-DS .942 .953 .625 20 1.3750-0.1P-0.2L-DS 1.068 .953 .625 22 1.5000-0.1P-0.2L-DS 1.192 .953 .625 24 1.7500-0.1P-0.2L-DS 1.317 1.047 .594 28 2.0000-0.1P-0.2L-DS 1.536 1.047 .594 32 2.2500-0.1P-0.2L-DS 1.786 1.111 .530 36 2.5000-0.1P-0.2L-DS 2.005 1.111 .530 40 2.7500-0.1P-0.2L-DS 2.255

5、1.111 .703 44 3.0000-0.1P-0.2L-DS 2.545 1.109 .703 Shell size M + .010 - .000 Q max QQ max R (TP) S + .021 - .020 T .005 12 .797 1.040 - .906 1.188 .150 14 .797 1.040 1.590 .969 1.281 .150 16 .797 1.040 1.590 1.062 1.375 .150 18 .797 1.025 1.575 1.156 1.500 .177 20 .797 1.025 1.575 1.250 1.625 .177

6、22 .797 1.025 1.575 1.375 1.750 .177 24 .859 .931 1.481 1.562 2.000 .177 28 .859 .931 1.481 1.750 2.250 .177 32 .922 .867 1.417 1.938 2.500 .209 36 .922 .867 1.417 2.188 2.750 .209 40 .922 .867 1.417 2.375 3.000 .209 44 .922 NA NA 2.625 3.250 .209 FIGURE 1. Dimensions and configuration - Continued.

7、Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS17343G 4 Shell size V Thread (plated) class 2A LH EE dia +.001 -.007 YY dia +.010 -.006 AAA BBB 12 .7500-20 UNEF .672 .647 .126 -.001, +.007 .063 -.001, +.007 14 .8750-20 UNEF .797 .772 16 1.0000-20 U

8、NEF .922 .897 .182 -.001, +.010 .108 -.001, +.010 18 1.1250-18 NEF 1.040 1.022 20 1.2500-18 NEF 1.164 1.148 22 1.3750-18 NEF 1.289 1.272 24 1.6250-18 NEF 1.539 1.473 .260 -.001, +.010 .155 -.001, +.010 28 1.8750-16 UN 1.780 1.692 32 2.0625-16 N 1.967 1.942 36 2.3125-16 N 2.217 2.161 40 2.6250-16 UN

9、2.530 2.411 44 2.8750-16 UN 2.780 2.692 FIGURE 1. Dimensions and configuration - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS17343G 5 Shell size CCC DDD Socket insert location .030 EEE Pin insert location .030 Z max (see note 7) Z mi

10、n (size 0 contacts only) 12 .0035 .020 .729 .726 NA 14 16 .007 18 .711 20 .780 22 24 .617 .686 28 32 .553 .622 36 40 44 .039 .744 .797 FIGURE 1. Dimensions and configuration - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS17343G 6 Inch

11、es mm Inches mm Inches mm Inches mm Inches mm .001 .0035 .005 .006 .007 .010 .020 .021 .030 .031 .039 .062 .063 .108 .126 .141 .150 .155 .177 .182 .209 .260 .530 .553 .567 .594 .617 0.03 0.089 0.13 0.15 0.18 0.25 0.51 0.53 0.76 0.79 0.99 1.57 1.60 2.74 3.20 3.58 3.81 3.94 4.50 4.62 5.31 6.60 13.46 1

12、4.06 14.40 15.09 15.67 .622 .625 .640 .647 .672 .686 .692 .703 .711 .726 .729 .750 .764 .772 .780 .797 .817 .859 .867 .875 .897 .906 .922 .931 .938 .942 .953 15.80 15.86 16.26 16.43 17.07 17.42 17.58 17.86 18.06 18.44 18.52 19.05 19.40 19.61 19.81 20.24 20.75 21.82 22.02 22.22 22.78 23.01 23.42 23.6

13、5 23.83 23.93 24.21 .969 1.000 1.022 1.025 1.040 1.047 1.062 1.068 1.109 1.111 1.125 1.148 1.156 1.164 1.188 1.192 1.250 1.272 1.281 1.289 1.317 1.375 1.375 1.417 1.473 1.481 24.61 25.40 25.96 26.04 25.42 26.59 26.97 27.13 28.17 28.22 28.60 29.16 29.36 39.57 30.18 31.28 31.75 32.31 32.54 32.74 33.45

14、 34.92 34.93 35.99 37.41 37.62 1.500 1.536 1.539 1.562 1.575 1.590 1.625 1.692 1.750 1.786 1.875 1.938 1.942 1.967 2.000 2.005 2.0625 2.161 2.1885 2.217 2.250 2.255 38.10 39.01 39.09 39.67 40.01 40.39 41.28 42.98 44.45 45.36 47.62 49.23 49.33 49.96 50.80 50.93 52.40 54.89 55.60 56.31 57.15 57.28 2.3

15、125 2.375 2.411 2.375 2.500 2.530 2.625 2.692 2.750 2.780 2.8750 3.000 3.125 3.250 58.74 60.33 61.24 60.33 63.50 64.25 66.68 68.38 69.85 70.61 73.020 76.20 79.38 82.55 NOTES: 1. All dimensions are in inches. 2. Unless otherwise specified, tolerances are .016 inch (0.41 mm). 3. Metric equivalents are

16、 given for information only. 4. Maximum termination of grommet extension for sizes 12 and 16 contacts for class J. 5. Maximum termination of grommet extension for sizes 0, 4, and 8 contacts for class J. 6. Dimensions shall be maintained when inserts are pressed firmly against indicated shoulder. 7.

17、For size 0 contacts only: Increase Z dimension by .312 inch (7.92 mm) for shell sizes 12 through 40, and increase Z dimension by .062 inch (1.57 mm) for shell size 44. FIGURE 1. Dimensions and configuration - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without lic

18、ense from IHS-,-,-MS17343G 7 REQUIREMENTS: Design and construction: See figure 1. Mates with plugs shown on MS17344 and covers shown on MS17349. Class shall be designated by the letter C (pressurized), J (pressurized with grommet) or R (environmental resisting). For shell size, insert arrangement, a

19、lternate position, contact size, spacing and service rating, see MIL-STD-1651. Shell finish: See MIL-DTL-22992. Part or Identifying Number (PIN) example: MS17343 R 20 C 27 P W MS number Class Shell size Finish Insert arrangement Contact style Alternate position Changes from previous issue. Marginal

20、notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Referenced documents. In addition to MIL-DTL-22992, this document references the following: MS17344 MS17349 MIL-STD-1651 Provided by IHSNot for ResaleNo reproduction or ne

21、tworking permitted without license from IHS-,-,-MS17343G 8 CONCLUDING MATERIAL Custodians: Preparing activity: Army CR DLA CC Navy EC Air Force 85 DLA CC Review activities: (Project 5935-2012-179) Army AR, MI Navy AS, CG, MC, OS, SH, YD Air Force 19, 99 NASA NA NOTE: The activities listed above were

22、 interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-