DLA MS9196 REV B-2010 TEE TUBE - SAE-AMS5646 BOSS.pdf

《DLA MS9196 REV B-2010 TEE TUBE - SAE-AMS5646 BOSS.pdf》由会员分享，可在线阅读，更多相关《DLA MS9196 REV B-2010 TEE TUBE - SAE-AMS5646 BOSS.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、 MS9196B 16 February 2010 SUPERSEDING MS9196A (ASG) 11 May 1962 DETAIL SPECIFICATION SHEET TEE, TUBE - SAE-AMS5646, BOSS This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of t

2、his specification sheet and SAE-AS4841. FIGURE 1. Tee, tube, boss. AMSC N/A FSC 4730INCH-POUND Inactive for new design after 20 September 2000. Inches mm .005 .020 .030 0.13 0.51 0.76 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS9196B 2 Dash num

3、ber Tube OD (reference) inches (mm) A diameter inches (mm) B inches (mm) +.015 (0.38) -.000 C diameter inches (mm) +.000 -.010 (0.25) -02 .125 (3.18) .058 (1.47) - .065 (1.65) .144 (3.66) .245 (6.22) -03 .188 (4.78) .121 (3.07) - .128 (3.25) .144 (3.66) .307 (7.80) -04 .250 (6.35) .168 (4.27) - .175

4、 (4.45) .160 (4.06) .359 (9.12) -05 .313 (7.95) .230 (5.84) - .237 (6.02) .160 (4.06) .421 (10.69) -06 .375 (9.53) .293 (7.44) - .301 (7.65) .165 (4.19) .476 (12.09) -07 .438 (11.13) .355 (9.02) - .363 (9.22) .165 (4.19) .539 (13.69) -08 .500 (12.70) .387 (9.83) - .395 (10.03) .229 (5.82) .654 (16.6

5、1) -09 .562 (14.27) .434 (11.02) - .442 (11.23) .229 (5.82) .716 (18.19) -10 .625 (15.88) .480 (12.19) - .488 (12.40) .255 (6.48) .767 (19.48) -11 .688 (17.48) .542 (13.77) - .552 (14.02) .304 (7.72) .875 (22.23) -12 .750 (19.05) .604 (15.34) - .614 (15.60) .304 (7.72) .938 (23.83) -14 .875 (22.23)

6、.729 (18.52) - .739 (18.77) .304 (7.72) 1.062 (26.97) -16 1.000 (25.40) .839 (21.31) - .851 (21.62) .312 (7.92) 1.188 (30.18) -18 1.125 (28.58) .948 (24.08) - .960 (24.38) .312 (7.92) 1.375 (34.93) -20 1.250 (31.75) 1.073 (27.25) - 1.086 (27.58) .363 (9.22) 1.500 (38.10) -24 1.500 (38.10) 1.307 (33.

7、20) - 1.320 (33.53) .374 (9.50) 1.750 (44.45) -28 1.750 (44.45) 1.542 (39.17) - 1.557 (39.55) .447 (11.35) 2.125 (53.98) -32 2.000 (50.80) 1.776 (45.11) - 1.791 (45.49) .457 (11.61) 2.375 (60.33) FIGURE 1. Tee, tube, boss - Continued. Provided by IHSNot for ResaleNo reproduction or networking permit

8、ted without license from IHS-,-,-MS9196B 3 Dash number D diameter inches (mm) .003 (0.08) F diameter inches (mm) +.002 (0.05) -.003 (0.08) (see notes 5 and 6) G diameter inches (mm) H inches (mm) .010 (0.25) J inches (mm) .010 (0.25) -02 .132 (3.35) .250 (6.35) .240 (6.10) .208 (5.28) .317 (8.05) -0

9、3 .195 (4.95) .312 (7.92) .300 (7.62) .208 (5.28) .346 (8.79) -04 .242 (6.15) .364 (9.25) .350 (8.89) .250 (6.35) .398 (10.11) -05 .304 (7.72) .426 (10.82) .415 (10.54) .250 (6.35) .398 (10.11) -06 .368 (9.35) .481 (12.22) .470 (11.94) .278 (7.06) .398 (10.11) -07 .430 (10.92) .544 (13.82) .535 (13.

10、59) .278 (7.06) .398 (10.11) -08 .462 (11.73) .660 (16.76) .650 (16.51) .312 (7.92) .489 (12.42) -09 .509 (12.93) .722 (18.34) .710 (18.03) .312 (7.92) .489 (12.42) -10 .555 (14.10) .773 (19.63) .765 (19.43) .357 (9.07) .585 (14.86) -11 .619 (15.72) .882 (22.40) .870 (22.10) .417 (10.59) .663 (16.84

11、) -12 .681 (17.30) .945 (24.00) .935 (23.75) .417 (10.59) .663 (16.84) -14 .808 (20.52) 1.070 (27.18) 1.055 (26.80) .417 (10.59) .710 (18.03) -16 .918 (23.32) 1.195 (30.35) 1.185 (30.10) .417 (10.59) .720 (18.29) -18 1.027 (26.09) 1.382 (35.10) 1.365 (34.67) .417 (10.59) .767 (19.48) -20 1.153 (29.2

12、9) 1.507 (38.28) 1.495 (37.97) .417 (10.59) .767 (19.48) -24 1.387 (35.23) 1.756 (44.60) 1.745 (44.32) .417 (10.59) .889 (22.58) -28 1.652 (41.96) 2.131 (54.13) 2.120 (53.85) .417 (10.59) 1.017 (25.83) -32 1.886 (47.90) 2.381 (60.48) 2.370 (60.20) .417 (10.59) 1.142 (29.01) FIGURE 1. Tee, tube, boss

13、 - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS9196B 4 Dash number K inches (mm) .010 (0.25) M min inches (mm) N inches (mm) +.010 (0.25) -.000 -02 .682 (17.32) .030 (0.76) .125 (3.18) -03 .682 (17.32) .030 (0.76) .131 (3.33) -04 .74

14、8 (19.00) .030 (0.76) .140 (3.56) -05 .748 (19.00) .030 (0.76) .140 (3.56) -06 .813 (20.65) .030 (0.76) .156 (3.96) -07 .813 (20.65) .030 (0.76) .172 (4.37) -08 .903 (22.94) .030 (0.76) .187 (4.75) -09 .903 (22.94) .030 (0.76) .203 (5.16) -10 1.018 (25.86) .030 (0.76) .219 (5.56) -11 1.122 (28.50) .

15、030 (0.76) .234 (5.94) -12 1.122 (28.50) .030 (0.76) .234 (5.94) -14 1.122 (28.50) .030 (0.76) .234 (5.94) -16 1.122 (28.50) .030 (0.76) .234 (5.94) -18 1.122 (28.50) .030 (0.76) .234 (5.94) -20 1.122 (28.50) .030 (0.76) .234 (5.94) -24 1.122 (28.50) .030 (0.76) .234 (5.94) -28 1.205 (30.61) .044 (1

16、.12) .234 (5.94) -32 1.320 (33.53) .044 (1.12) .234 (5.94) FIGURE 1. Tee, tube, boss - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS9196B 5 Dash number P inches (mm) Q inches (mm) .010 (0.25) S inches (mm) +.010 (0.25) Thread T (see n

17、ote 11) -02 .020 (0.51) - .050 (1.27) .707 (17.96) 1.000 (25.40) .3125 - 24UNF - 3A -03 .020 (0.51) - .050 (1.27) .764 (19.41) 1.000 (25.40) .375 - 24UNF - 3A -04 .030 (0.76) - .060 (1.52) .826 (20.98) 1.115 (28.32) .4375 - 20UNF - 3A -05 .030 (0.76) - .060 (1.52) .889 (22.58) 1.140 (28.96) .500 - 2

18、0UNF - 3A -06 .040 (1.02) - .070 (1.78) .998 (25.35) 1.270 (32.26) .5625 - 18UNF-3A -07 .040 (1.02) - .070 (1.78) .998 (25.35) 1.305 (33.15) .625 - 18UNF 3A -08 .040 (1.02) - .070 (1.78) 1.195 (30.35) 1.460 (37.08) .7500 - 16UNF - 3A -09 .040 (1.02) - .070 (1.78) 1.195 (30.35) 1.490 (37.85) .8125 -

19、16UN - 3A -10 .050 (1.27) - .080 (2.03) 1.411 (35.84) 1.680 (42.67) .8750 - 14UNF - 3A -11 .050 (1.27) - .080 (2.03) 1.614 (41.00) 1.855 (47.12) 1.000 - 12UNF - 3A -12 .050 (1.27) - .080 (2.03) 1.614 (41.00) 1.885 (47.88) 1.0625 - 12UN - 3A -14 .050 (1.27) - .080 (2.03) 1.768 (44.91) 1.945 (49.40) 1

20、.1875 - 12UN - 3A -16 .050 (1.27) - .080 (2.03) 1.778 (45.16) 2.010 (51.05) 1.3125 - 12UN - 3A -18 .050 (1.27) - .080 (2.03) 2.027 (51.49) 2.100 (53.34) 1.500 - 12UNF - 3A -20 .050 (1.27) - .080 (2.03) 2.027 (51.49) 2.165 (54.99) 1.625- 12UN - 3A -24 .050 (1.27) - .080 (2.03) 2.293 (58.24) 2.290 (58

21、.17) 1.8750 - 12UN - 3A -28 .050 (1.27) - .080 (2.03) 2.777 (70.54) 2.625 (66.68) 2.2500 - 12UN - 3A -32 .050 (1.27) - .080 (2.03) 3.027 (76.89) 2.975 (75.57) 2.500 - 12UN - 3A FIGURE 1. Tee, tube, boss - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license

22、 from IHS-,-,-MS9196B 6 Dash number Thread TT (see note 11) Size Major diameter inches (mm) Pitch diameter inches (mm) Minor diameter max inches (mm) -02 .3125 24UNS-3A .3023 (7.678) - .3095 (7.861) .2797 (7.104) - .2824 (7.173) .2584 (6.563) -03 .375 24UNS-3A .3648 (9.266) - .3720 (9.449) .3420 (8.

23、687) - .3449 (8.760) .3209 (8.151) -04 .4375 20UNS-3A .4264 (10.831) - .4345 (11.036) .3989 (10.132) - .4020 (10.211) .3732 (9.479) -05 .500 20UNS-3A .4889 (12.418) - .4970 (12.623) .4613 (11.717) - .4645 (11.798) .4357 (11.067) -06 .5625 18UNS-3A .5508 (13.990) - .5595 (14.211) .5200 (13.208) - .52

24、34 (13.294) .4913 (12.479) -07 .625 18UNS-3A .6133 (15.578) - .6220 (15.799) .5824 (14.793) - .5859 (14.881) .5538 (14.067) -08 .750 16UNS-3A .7376 (18.735) - .7470 (18.974) .7026 (17.846) - .7064 (17.942) .6703 (17.026) -09 .8125 16UNS-3A .8001 (20.323) - .8095 (20.561) .7653 (19.44) - .7689 (19.53

25、0) .7328 (18.613) -10 .875 14UNS-3A .8617 (21.887) - .8720 (22.149) .8215 (20.866) - .8256 (20.970) .7844 (19.924) -11 1.000 12UNS-3A .9856 (25.034) - .9970 (25.324) .9385 (23.838) - .9429 (23.950) .8948 (22.728) -12 1.0625 12UNS-3A 1.0481 (26.622) - 1.0595 (26.911) 1.0012 (25.430) - 1.0054 (25.537)

26、 .9573 (24.315) -14 1.1875 12UNS-3A 1.1731 (29.797) - 1.1845 (30.086) 1.1261 (28.603) - 1.1304 (28.712) 1.0823 (27.490) -16 1.3125 12UNS-3A 1.2981 (32.972) - 1.3095 (33.261) 1.2511 (31.778) - 1.2554 (31.887) 1.2073 (30.665) -18 1.500 12UNS-3A 1.4856 (37.734) - 1.4970 (38.024) 1.4381 (36.528) - 1.442

27、9 (36.650) 1.3948 (35.428) -20 1.625 12UNS-3 1.6106 (40.909) - 1.6220 (41.199) 1.5635 (39.713) - 1.5679 (39.825) 1.5198 (38.603) -24 1.875 12UNS-3 1.8606 (47.259) - 1.8720 (47.549) 1.8134 (46.060) - 1.8179 (46.175) 1.7698 (44.953) -28 2.250 12UNS-3A 2.2356 (56.784) - 2.2470 (57.074) 2.1884 (55.585)

28、- 2.1929 (55.700) 2.1448 (54.478) -32 2.500 12UNS-3A 2.4856 (63.134) - 2.4970 (63.424) 2.4429 (62.050) - 2.4383 (61.933) 2.3948 (60.828) FIGURE 1. Tee, tube, boss - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS9196B 7 Dash number U ra

29、dius inches (mm) V inches (mm) W inches (mm) X inches (mm) Y inches (mm) -02 .062 (1.57) .250 (6.35) .400 (10.16) .200 (5.08) .300 (7.62) -03 .062 (1.57) .312 (7.92) .400 (10.16) .220 (5.59) .310 (7.87) -04 .062 (1.57) .375 (9.53) .500 (12.70) .260 (6.60) .360 (9.14) -05 .062 (1.57) .438 (11.13) .58

30、0 (14.73) .300 (7.62) .420 (10.67) -06 .094 (2.39) .500 (12.70) .650 (16.51) .330 (8.38) .490 (12.45) -07 .094 (2.39) .562 (14.27) .650 (16.51) .330 (8.38) .490 (12.45) -08 .094 (2.39) .688 (17.48) .850 (21.59) .430 (10.92) .640 (16.26) -09 .094 (2.39) .750 (19.05) .880 (21.59) .440 (11.18) .660 (16

31、.76) -10 .094 (2.39) .812 (20.62) 1.000 (25.40) .500 (12.70) .750 (19.05) -11 .094 (2.39) .938 (23.83) 1.000 (25.40) .500 (12.70) .750 (19.05) -12 .094 (2.39) 1.000 (25.40) 1.000 (25.40) .500 (12.70) .750 (19.05) -14 .125 (3.18) 1.125 (28.58) 1.000 (25.40) .500 (12.70) .750 (19.05) -16 .125 (3.18) 1

32、.250 (31.75) 1.000 (25.40) .500 (12.70) .750 (19.05) -18 .125 (3.18) 1.438 (36.53) 1.200 (30.48) .600 (15.24) .900 (22.86) -20 .125 (3.18) 1.625 (41.28) 1.200 (30.48 .600 (15.24) .900 (22.86) -24 .125 (3.18) 1.812 (46.02) 1.200 (30.48) .600 (15.24) .900 (22.86) -28 .188 (4.78) 2.188 (55.58) 1.320 (3

33、3.53) .660 (16.76) .990 (25.15) -32 .250 (6.35) 2.438 (61.93) 1.500 (38.10) .750 (19.05) 1.125 (28.58) FIGURE 1. Tee, tube, boss - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS9196B 8 NOTES: 1. Dimensions are in inches. 2. Metric equi

34、valents are given for information only. 3. Unless otherwise specified tolerances for linear dimensions are .015 inch (0.38 mm) and angular dimensions are 5, all diameters shall be concentric within .010 inch (0.25 mm) FIM. 4. Unless otherwise specified machined surfaces to be 125 inches (3.18m) in a

35、ccordance with ASME B46.1. 5. Diameter F shall be free of thread marks. 6. Diameter F shall be concentric with PD of thread within .0025 inch (1.134 mm) FIM. 7. Lettering height: For size -02 through -04 dimension: .020 - .040 inch (0.51 - 1.02 mm). For size -05 through -16 dimension: .040 - .060 in

36、ch (1.02 - 1.52 mm). For size -18 and larger dimension: .090 - .150 inch (2.29 - 3.81 mm). 8. Parting line mismatch .015 inch (0.38 mm) max. 9. Unless otherwise specified break sharp edges .003 - .015 inches (0.08 - 0.38 mm). 10. Dimensions are to sharp corners unless otherwise specified. 11. All th

37、reads shall be in accordance with FED-STD-H28/2. FIGURE 1. Tee, tube, boss - Continued. REQUIREMENTS: Dimensions and configurations: See figure 1. Material: Steel, corrosion and heat-resistant in accordance with SAE-AMS5646. Max operating temperature: Oxidation resistance up to 1500F (816C). Max ope

38、rating pressure: 1500 psi (10 MPa). Finish: Passivate in accordance with SAE-AMS2700, method 1. All parts shall be fluorescent penetrant inspected in accordance with ASTM E1417. PIN: MS9196 -08 PIN Example: MS9196-08 identifies a tee .500 inch (tube), CRES. Do not use unassigned PINs. The approximat

39、e weight for each fitting is shown in table I Specification sheet number Elbow size (see figure 1) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS9196B 9 TABLE I. Approximate weight. Dash number Approx Weight lbs/ea (grams/ea) Dash number Approx W

40、eight lbs/ea (grams/ea) -02 .033 (15) -11 .528 (239) -03 .047 (21) -12 .569 (258) -04 .066 (30) -14 .691 (313) -05 .085 (39) -16 .811 (368) -06 .108 (49) -18 1.207 (547) -07 .124 (56) -20 1.347 (611) -08 .239 (108) -24 1.780 (807) -09 .272 (123) -28 3.249 (1474) -10 .361 (164) -32 4.166 (1890) Inten

41、ded usage: Jet engine, miscellaneous parts, oil, fuel, and de-icing kits. Not to be used on hydraulic, oxygen or applications requiring pressures of 3000 psi (21 MPa). Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue

42、 due to the extent of the changes. Referenced documents. In addition to SAE-AS4841, this document references the following: FED-STD-H28/2 ASME B46.1 ASTM E1417 SAE-AS478 SAE-AMS2700 SAE-AMS5646 CONCLUDING MATERIAL Custodians: Preparing activity: Navy - AS DLA - CC DLA - CC (Project 4730-2009-082) Re

43、view activity: Navy - SA NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-