DLA MS3124 REV G-2011 CONNECTORS RECEPTACLE ELECTRIC CRIMP TYPE REAR MOUNTING JAM NUT BAYONET COUPLING SERIES 1 CLASSES E F AND P.pdf

《DLA MS3124 REV G-2011 CONNECTORS RECEPTACLE ELECTRIC CRIMP TYPE REAR MOUNTING JAM NUT BAYONET COUPLING SERIES 1 CLASSES E F AND P.pdf》由会员分享，可在线阅读，更多相关《DLA MS3124 REV G-2011 CONNECTORS RECEPTACLE ELECTRIC CRIMP TYPE REAR MOUNTING JAM NUT BAYONET COUPLING SERIES 1 CLASSES E F AND P.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、 DETAIL SPECIFICATION SHEET CONNECTORS, RECEPTACLE, ELECTRIC, CRIMP TYPE, REAR MOUNTING, JAM NUT, BAYONET COUPLING, SERIES 1, CLASSES E, F AND P This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described h

2、erein shall consist of this specification sheet and MIL-DTL-26482. STYLE P (PIN INSERT) FIGURE 1. Receptacle, dimensions, classes E, F and P. AMSC N/A FSC 5935 MS3124G 31 October 2011 SUPERSEDING MS3124F 07 November 2007 Inches mm .001 0.03 .0035 0.09 .007 0.18 .010 0.25 .063 1.60 .126 3.20 Inactive

3、 for new design after 5 September 1975. INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS3124G 2 Inches mm .007 0.18 .010 0.25 .020 0.51 .031 0.79 .070 1.78 .156 3.96 FIGURE 1. Receptacle, dimensions, classes E, F, and P - Continued. Prov

4、ided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS3124G 3 FIGURE 1. Receptacle, dimensions, classes E, F and P Continued. Shell size DD +.011 O-ring protection HH max ID gasket FF +.010 -.005 panel mounting hole GG +.010 -.005 panel flat location 8 .023

5、(0.58) .329 (8.36) .572 (14.53) .540 (13.72) 10 .457 (11.61) .697 (17.70) .665 (16.89) 12 .564 (14.33) .885 (22.48) .828 (21.03) 14 .689 (17.50) 1.010 (25.65) .952 (24.18) 16 .814 (20.68) 1.135 (28.83) 1.076 (27.33) 18 .907 (23.04) 1.260 (32.00) 1.201 (30.51) 20 .028 (0.71) 1.032 (26.21) 1.385 (35.1

6、8) 1.326 (33.68) 22 1.164 (29.57) 1.510 (38.35) 1.451 (36.86) 24 1.259 (31.98) 1.635 (41.53) 1.576 (40.03) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS3124G 4 Shell size A dia +.001 -.005 OD B dia +.006 -.002 bay pin C dia +.000 -.016 over bay

7、pins D dia +.005 -.001 ID E +.000 -.010 mounting flat F min mounting thread location G +.000 -.032 across flange corner 8 .473 (12.01) .078 (1.98) .563 (14.30) .362 (9.19) .530 (13.46) .384 (9.75) 1.078 (27.38) 10 .590 (14.99) .680 (17.27) .490 (12.45) .655 (16.64) 1.203 (30.56) 12 .750 (19.05) .859

8、 (21.82) .607 (15.42) .818 (20.78) 1.391 (35.33) 14 .875 (22.23) .984 (24.99) .732 (18.59) .942 (23.93) 1.516 (38.51) 16 1.000 (25.40) 1.108 (28.14) .857 (21.77) 1.066 (27.08) 1.641 (41.68) 18 1.125 (28.58) 1.233 (31.32) .962 (24.43) 1.191 (30.25) 1.766 (44.86) 20 1.250 (31.75) 1.358 (34.49) 1.087 (

9、27.61) 1.316 (33.43) .446 (11.33) 1.954 (49.63) 22 1.375 (34.93) 1.483 (37.67) 1.212 (30.78) 1.441 (36.60) 2.078 (52.78) 24 1.500 (38.10) .125 (3.18) 1.610 (40.89) 1.337 (33.96) 1.566 (39.78) .479 (12.17) 2.203 (55.96) FIGURE 1. Receptacle, dimensions, classes E, F and P Continued. Provided by IHSNo

10、t for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS3124G 5 FIGURE 1. Receptacle, dimensions, classes E, F and P Continued. Shell size H + .000 - .020 socket insert location I dia max insert J + .010 packing location JJ + .000 - .020 pin insert location K .016 thick mo

11、unting flange M + .031 - .000 mounting flange location 8 .025 (0.64) .285 (7.24) .382 (9.70) .332 (8.43) .117 (2.97) .691 (17.55) 10 .402 (10.21) 12 .516 (13.11) 14 .641 (16.28) 16 .766 (19.46) 18 .855 (21.72) 20 .087 (2.21) .980 (24.89) .444 (11.28) .394 (10.01) .148 (3.76) .879 (22.33) 22 1.105 (2

12、8.07) 24 1.229 (31.22) .912 (23.16) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS3124G 6 Shell size P panel thickness (ref) Q dia +.005 -.006 over keyways S max length side U +.010 -.020 pin contact location V class 2A mounting thread min max 8

13、.062 (1.57) .125 (3.18) .412 (10.46) .954 (24.23) .085 (2.16) 9/16-24 10 .540 (13.72) 1.078 (27.38) 11/16-24 12 .689 (17.50) 1.266 (32.16) 7/8-20 14 .814 (20.68) 1.391 (35.33) 1-20 16 .939 (23.85) 1.516 (38.51) 1-1/8-18 18 1.039 (26.39) 1.641 (41.68) 1-1/4-18 20 .250 (6.35) 1.164 (29.57) 1.828 (46.6

14、3) .147 (3.73) 1-3/8-18 22 1.289 (32.74) 1.954 (49.63) 1-1/2-18 24 1.414 (35.92) 2.078 (52.78) 1-5/8-18 Shell size W (TP) bay pin location Z (b) + .000 - .078 socket contact spring location YY O-ring seal MS29513- (per SAE-AS29513) V V class 2B accessory thread 8 .100 (2.54) .153 (3.89) 017 5/8-24 1

15、0 019 3/4-20 12 022 7/8-20 14 024 1-20 16 026 1-1/8-18 18 028 1-1/4-18 20 .215 (5.46) 128 1-3/8-18 22 130 1-1/2-18 24 .109 (2.77) 132 1-5/8-18 FIGURE 1. Receptacle, dimensions, classes E, F and P Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS

16、-,-,-MS3124G 7 Class E Dimensions class E only Shell size L max over-all length X dia min ID Y dia max OD 8 1.552 (39.42) .259 (6.58) .750 (19.05) 10 .359 (9.12) .875 (22.23) 12 .469 (11.91) 1.000 (25.40) 14 .589 (14.96) 1.125 (28.58) 16 .717 (18.21) 1.250 (31.75) 18 .779 (19.79) 1.375 (34.93) 20 1.

17、709 (43.41) .901 (22.89) 1.531 (38.89) 22 1.009 (25.63) 1.656 (42.06) 24 1.123 (28.52) 1.781 (45.24) FIGURE 1. Receptacle, dimensions, classes E, F and P Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS3124G 8 Class F Inch mm .430 10.92

18、Class F, bushing removed FIGURE 1. Receptacle, dimensions, classes E, F and P Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS3124G 9 FIGURE 1. Receptacle, dimensions, classes E, F and P Continued. Dimensions, class F only Shell size L m

19、ax over-all length X dla min open Y max V max closed 8 2.422 (61.52) .234 (5.94) .828 (21.03) .187 (4.75) 10 .297 (7.54) .891 (22.63) .187 (4.75) 12 .422 (10.72) 1.016 (25.81) .281 (7.14) 14 .547 (13.89) 1.141 (28.98) .325 (8.26) 16 2.537 (64.44) .609 (15.47) 1.203 (30.56) .356 (9.04) 18 .734 (18.64

20、) 1.469 (37.31) .456 (11.58) 20 2.824 (71.73) .519 (13.18) 22 .922 (23.42) 1.656 (42.06) 24 2.900 (73.66) .984 (24.99) 1.750 (44.45) .657 (16.69) Dimensions, class F only Shell size N free dia .010 ZZ screw threads YZ lockwashers NASM35338 NASM35333 8 .110 (2.79) 6-32 UNC NASM35338 -98 or -41 NASM35

21、333 -105 or -37 10 .173 (4.39) 12 .297 (7.54) 14 .360 (9.14) 16 .485 (12.32) 18 .610 (15.49) 8-32 UNC NASM35338 -99 or -42 NASM35333 -106 or -38 20 .610 (15.49) 22 .735 (18.67) 24 .785 (19.94) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS3124G 1

22、0 Class P NOTES: 1. Dimensions are in inches. Metric equivalents are given for information only. 2. Distance between end of shell and the point at which a gage pin having the same basic diameter as the mating contact and a square face first engages socket contact spring. 3. Packing material shall me

23、et the requirements of ASTM-D2000. 4. True position (TP) tolerances specified are in accordance with ASME Y14.5M. 5. For class F: Use SAE-AS85049/139 bushing if reduced opening is required. Lockwashers may be captivated. FIGURE 1. Receptacle, dimensions, classes E, F and P Continued. Dimensions clas

24、s P only Shell size L max over-all length X dia min Y dia max PP min 8 1.675 (42.55) .317 (8.05) .608 (15.44) .250 (6.35) 10 .434 (11.02) .734 (18.64) 12 .548 (13.92) .858 (21.79) 14 .673 (17.09) .984 (24.99) 16 .798 (20.27) 1.110 (28.19) 18 .899 (22.83) 1.234 (31.34) 20 1.963 (49.86) 1.024 (26.01)

25、1.360 (34.54) 22 1.963 (49.86) 1.149 (29.18) 1.484 (37.69) 24 2.025 (51.44) 1.274 (32.36) 1.610 (40.89) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS3124G 11 REQUIREMENTS: Dimensions and configuration: See figure 1. Connector mating: This connec

26、tor mates with MS3121 and MS3126. Insert arrangement shall be in accordance with MIL-STD-1669. Sealing member: Bonded to vitreous insert. Packing material shall meet the requirements of ASTM-D2000. Finishes: A finish designator shall not be included in the PIN when finish W is required. See MIL-DTL-

27、26482 for alternative finishes D, T and Z for classes E, F and P. Material: a. Shell - aluminum alloy. b. Bayonet pins (B dia) - stainless steel, passivated. Part or Identifying Number (PIN) example: MS3124 E 12 - 3 P W D MS number Class Shell size Insert arrangement Contact style Alternate insert p

28、osition Finish Note: When finish W is required, no finish designator is used (class W is the default finish). Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Referenced documents. I

29、n addition to MIL-DTL-26482, this document references the following: MS3121 MS3126 MS3186 MIL-STD-1669 ASME Y14.5M ASTM-D2000 SAE-AS29513 SAE-AS39029/31 SAE-AS39029/32 SAE-AS85049/139 NASM35333 NASM35338 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-

30、,-MS3124G 12 CONCLUDING MATERIAL Custodians: Preparing activity: Army - CR DLA - CC Air Force - 85 DLA - CC (Project 5935-2011-111) Review activities: Army - AR, MI NOTE: The activities listed above were interested in this document as of the date of this document. Since organization and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-