书签分享收藏举报版权申诉 / 11

立即下载加入VIP,交流精品资源

当前位置：首页 > 标准规范 > 国际标准 > 其他 > DLA MS3116 REV E-2013 CONNECTORS PLUG ELECTRICAL SOLDER TYPE STRAIGHT BAYONET COUPLING SERIES 1 CLASSES E F J AND P.pdf

DLA MS3116 REV E-2013 CONNECTORS PLUG ELECTRICAL SOLDER TYPE STRAIGHT BAYONET COUPLING SERIES 1 CLASSES E F J AND P.pdf

上传人：orderah291

文档编号：693785

上传时间：2018-12-30

格式：PDF

页数：11

大小：115.36KB

《DLA MS3116 REV E-2013 CONNECTORS PLUG ELECTRICAL SOLDER TYPE STRAIGHT BAYONET COUPLING SERIES 1 CLASSES E F J AND P.pdf》由会员分享，可在线阅读，更多相关《DLA MS3116 REV E-2013 CONNECTORS PLUG ELECTRICAL SOLDER TYPE STRAIGHT BAYONET COUPLING SERIES 1 CLASSES E F J AND P.pdf（11页珍藏版）》请在麦多课文档分享上搜索。

1、 MS3116E 12 September 2013 SUPERSEDING MS3116D 19 August 1976 DETAIL SPECIFICATION SHEET CONNECTORS, PLUG, ELECTRICAL, SOLDER TYPE, STRAIGHT, BAYONET COUPLING, SERIES 1, CLASSES E, F, J AND P This specification is approved for use by all Departments and Agencies of the Department of Defense. The req

2、uirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-26482. STYLE P STYLE S PIN INSERT SOCKET INSERT FIGURE 1. Plug, classes E, F, J, and P. AMSC N/A FSC 5935 Inactive for new design after 15 December 1998, and is no longer used, except for repla

3、cement purposes. INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS3116E 2 DETAIL A DETAIL B FIGURE 1. Plug, classes E, F, J and P - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,

4、-,-MS3116E 3 Shell size A dia overall F .010 shoulder location G .020 bay lock location J + .020 / - .000 socket insert location N class 2A accessory thread UNEF 8 .782 (19.86) .353 (8.97) .113 (2.87) .337 (8.56) .438-28 10 .926 (23.52) .562-24 12 1.043 (26.49) .6875-24 14 1.183 (30.05) .8125-20 16

5、1.305 (33.15) .9375-20 18 1.391 (35.33) 1.0625-18 20 1.531 (38.89) .415 (10.54) .399 (10.13) 1.1875-18 22 1.656 (42.06) 1.3125-18 24 1.777 (45.14) .152 (3.86) 1.4375-18 FIGURE 1. Receptacle, classes E, F, J, and P - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted with

6、out license from IHS-,-,-MS3116E 4 Inches mm Inches mm .005 0.13 .020 0.51 .010 0.25 .031 0.79 .015 0.38 .036 0.91 .016 0.41 .141 3.58 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. True position (TP) tolerances specified are in accordance with ASME-Y14.

7、5. FIGURE 1. Plug, classes E, F, J and P - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS3116E 5 CLASS E, REAR ACCESSORY CONFIGURATION Shell size L max overall length X dia min ID Y dia max OD 8 1.328 (33.73) .259 (6.58) .608 (15.44) 1

8、0 .359 (9.12) .734 (18.64) 12 .469 (11.91) .858 (21.79) 14 .589 (14.96) .984 (24.99) 16 .717 (18.21) 1.110 (28.19) 18 .779 (19.79) 1.234 (31.34) 20 1.453 (36.91) .901 (22.89) 1.360 (34.54) 22 1.009 (25.63) 1.484 (37.69) 24 1.510 (38.35) 1.123 (28.52) 1.610 (40.89) NOTES: 1. Dimensions are in inches.

9、 2. Metric equivalents are given for information only. 3. True position (TP) tolerances specified are in accordance with ASME-Y14.5. FIGURE 2. Plug, rear accessories configurations, class E. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS3116E 6 C

10、LASS F, WITH BUSHING CLASS F, WITH BUSHING REMOVED FIGURE 3. Plug, rear accessories configurations, class F. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS3116E 7 Shell size L max overall length Y max X dia min open V max closed N (see note 4) .0

11、10 free dia ZZ screw threads YZ (see note 5) lockwashers NASM35338 or NASM35333 types 8 1.906 (48.41) .828 (21.03) .234 (5.94) .187 (4.75) .125 (3.18) 6-32 UNC NASM35338 - 98 or -41 NASM35333 -105 or -37 10 .891 (22.63) .297 (7.54) .188 (4.78) 12 1.016 (25.81) .422 (10.72) .281 (7.14) .312 (7.92) 14

12、 1.141 (28.98) .547 (13.89) .325 (8.26) .375 (9.53) 16 2.047 (51.99) 1.203 (30.56) .609 (15.47) .356 (9.04) .500 (12.70) 18 2.078 (52.78) 1.469 (37.31) .734 (18.64) .456 (11.58) .625 (15.88) 8-32 UNC NASM35338 -B8L or -8L -99 or -42 NASM35333 -106 or -38 20 2.250 (57.15) .519 (13.18) 22 1.656 (42.06

13、) .922 (23.42) .750 (19.05) 24 2.312 (58.72) 1.750 (44.45) .984 (24.99) .657 (16.69) .800 (20.32) NOTES: 1. Dimensions are in inches. 2. Metric equivalents are in given for information only. 3. True position (TP) tolerances specified are in accordance with ASME-Y14.5. 4. Use SAE-AS85049/139 bushing

14、if reduced opening is required. 5. For class F: Lockwashers may be captivated. FIGURE 3. Plug, rear accessories configurations, class F - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS3116E 8 Shell size L max overall length V max close

15、d X ID gland seal min range Y dia max ZZ screw threads YZ (see note 4) Lockwashers NASM35338 or NASM35333 types closed open 8 2.271 (57.68) .187 (4.75) .169 (4.29) .230 (5.84) .828 (21.03) 6-32 UNC NASM35338 - 98 or -41 NASM35333 -105 or -37 10 .205 (5.21) .312 (7.92) .891 (22.63) 12 2.411 (61.24) .

16、281 (7.14) .338 (8.59) .442 (11.23) 1.016 (25.81) 14 2.599 (66.01) .325 (8.26) .416 (10.57) .539 (13.69) 1.161 (29.49) 16 2.943 (74.75) .356 (9.04) .550 (13.97) .616 (15.65) 1.203 (30.56) 18 3.172 (80.57) .456 (11.58) .600 (15.24) .672 (17.07) 1.469 (37.31) 8-32 UNC NASM35338 -B8L or -8L -99 or -42

17、NASM35333 -106 or -38 20 3.610 (91.69) .519 (13.18) .635 (16.13) .747 (18.97) 22 3.766 (95.66) .670 (17.02) .846 (21.49) 1.656 (42.06) 24 3.985 (101.22) .657 (16.69) .740 (18.79) .894 (22.71) 1.750 (44.45) NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. T

18、rue position (TP) tolerances specified are in accordance with ASME-Y14.5. 4. Lockwashers may be captivated. FIGURE 4. Plug, rear accessories configurations, class J. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS3116E 9 Shell size L max overall l

19、ength X dia min ID Y dia max OD PP min 8 1.500 (38.10) .317 (8.05) .608 (15.44) .250 (6.35) 10 .434 (11.02) .734 (18.64) 12 .548 (13.92) .858 (21.79) 14 .673 (17.09) .984 (24.99) 16 .798 (20.27) 1.110 (28.19) 18 .899 (22.83) 1.234 (31.34) 20 1.609 (40.87) 1.024 (26.01) 1.360 (34.54) 22 1.149 (29.18)

20、 1.484 (37.69) 24 1.687 (42.85) 1.274 (32.36) 1.610 (40.89) NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. True position (TP) tolerances specified are in accordance with ASME-Y14.5. FIGURE 5. Plug, rear accessories configurations, class P. Provided by IH

21、SNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS3116E 10 REQUIREMENTS: Dimensions and configurations: See figures 1 through 5. Connector mating: This connector mates with MS3110, MS3112, MS3113, MS3114 and MS3119. For insert arrangement: See MIL-STD-1669. Interm

22、ateability dimensions are in accordance with MIL-DTL-26482. Finishes: A finish designator shall not be included in the PIN when finish W is required. See MIL-DTL-26482 for other finishes, including D, T and K, available for classes E, F, P and J. Part or Identifying Number (PIN) example: MS3116 F 12

23、 -3 P W D MS number Class Shell size Insert arrangement Contact style Alternate insert position Finish Note: When finish W is required, no finish designator is used (class W is the default finish). Restrictions: Changes from previous issue. Marginal notations are not used in this revision to identif

24、y changes with respect to the previous issue due to the extent of the changes. Referenced documents. In addition to MIL-DTL-26482, this document references the following: MIL-STD-1669 ASME-Y14.5 SAE-AS85049/139 Not for Air Force use. For Air Force use, use MS3476. Provided by IHSNot for ResaleNo rep

25、roduction or networking permitted without license from IHS-,-,-MS3116E 11 CONCLUDING MATERIAL Custodians: Preparing activity: Army - CR DLA - CC Navy - AS Air Force - 85 DLA - CC Review activities: (Project 5935-2012-225) Army - AV Navy - EC, SH Air Force - 99 NOTE: The activities listed above were

26、interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-

下载提示：本站仅提供存储空间/不修改/不编辑

1.请仔细阅读文档，确保文档完整性，对于不预览、不比对内容而直接下载带来的问题本站不予受理。
2.下载的文档，不会出现我们的网址水印。
3、该文档所得收入（下载+内容+预览）归上传者、原创作者；如果您是本文档原作者，请点此认领！既往收益都归您。

同意并开始全文预览

文档包含非法信息？点此举报后获取现金奖励！

文档加载中……请稍候！
如果长时间未打开，您也可以点击刷新试试。

下载文档到电脑，查找使用更方便

10000 积分 0人已下载

下载	加入VIP,交流精品资源

版权申诉 word格式文档无特别注明外均可编辑修改；预览文档经过压缩，下载后原文更清晰！ 立即下载

配套讲稿：: 如PPT文件的首页显示word图标，表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
特殊限制：: 部分文档作品中含有的国旗、国徽等图片，仅作为作品整体效果示例展示，禁止商用。设计者仅对作品中独创性部分享有著作权。
关键词：: DLAMS3116REVE2013CONNECTORSPLUGELECTRICALSOLDERTYPESTRAIGHTBAYONETCOUPLINGSERIES1CLASSESEFJANDPPDF

麦多课文档分享所有资源均是用户自行上传分享，仅供网友学习交流，未经上传用户书面授权，请勿作他用。

关于本文

本文标题：DLA MS3116 REV E-2013 CONNECTORS PLUG ELECTRICAL SOLDER TYPE STRAIGHT BAYONET COUPLING SERIES 1 CLASSES E F J AND P.pdf
链接地址：http://www.mydoc123.com/p-693785.html