DLA MS3115 REV G-2009 CONNECTORS RECEPTACLE ELECTRICAL DUMMY STOWAGE BAYONET COUPLING FOR MIL-DTL-26482 CONNECTORS SERIES 1 AND 2.pdf

《DLA MS3115 REV G-2009 CONNECTORS RECEPTACLE ELECTRICAL DUMMY STOWAGE BAYONET COUPLING FOR MIL-DTL-26482 CONNECTORS SERIES 1 AND 2.pdf》由会员分享，可在线阅读，更多相关《DLA MS3115 REV G-2009 CONNECTORS RECEPTACLE ELECTRICAL DUMMY STOWAGE BAYONET COUPLING FOR MIL-DTL-26482 CONNECTORS SERIES 1 AND 2.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 MS3115G 29 April 2009 SUPERSEDING MS3115F 1 March 2007 INCH-POUNDDETAIL SPECIFICATION SHEET CONNECTORS, RECEPTACLE, ELECTRICAL, DUMMY STOWAGE, BAYONET COUPLING, FOR MIL-DTL-26482 CONNECTORS, SERIES 1 AND 2 Reactivated after 1 March 2007 and may be used for new and existing designs and acquisitions.

2、 This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-26482. FIGURE 1. Receptacle, dummy stowage, dimensions and configurations. AMSC N/A

3、FSC 5935 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS3115G 2Shell size A max length side B (TP) centerline-to-centerline mounting holes F + .031 - .000 mounting flange location G .016 thickness mounting flange H .005 dia mounting holes J + .010

4、 - .020 disk location P min edge distance 8 .828 (21.03) .594 (15.09) 10 .954 (24.23) .719 (18.26) 12 1.047 (26.59) .812 (20.62) 14 1.141 (28.98) .906 (23.01) 16 1.234 (31.34) .969 (24.61) 18 1.328 (33.73) 1.062 (26.97) .462 (11.73) .062 (1.57) .328 (8.33) .035 (0.89) 20 1.453 (36.91) 1.156 (29.36)

5、22 1.578 (40.08) 1.250 (31.75) .556 (14.12) .120 (3.05) 24 1.703 (43.26) 1.375 (34.93) .589 (14.96) .094 (2.39) .147 (3.73) .390 (9.91) .050 (1.27) Inches mm .005 0.13 .010 0.25 .015 0.38 .016 0.41 .020 0.51 .031 0.79 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for informatio

6、n only. 3 True position (TP) tolerances specified are in accordance with ASME Y14.5M. 4. Intermateability dimensions shall be in accordance with MIL-DTL-26482. FIGURE 1. Receptacle, dummy stowage, dimensions and configurations - Continued. Provided by IHSNot for ResaleNo reproduction or networking p

7、ermitted without license from IHS-,-,-MS3115G 3REQUIREMENTS: Dimensions and configuration: See figure 1. Materials: a. Dummy stowage - aluminum alloy. b. Disk material - synthetic rubber or silicone elastomer. Finish: A, D, L, T, W and Z. Finish E is superseded by Finish W. Fluid resistance: This du

8、mmy stowage receptacle shall meet the fluid resistance requirements in accordance with MIL-DTL-26482, series 1 and 2. Connector mating: This connector mates with all MIL-DTL-26482, series 1 and 2 connector plugs. Intermateability dimensions shall be in accordance with MIL-DTL-26482. Part or Identify

9、ing Number (PIN) example: MS3115 - 12 L MS number Shell size Finish Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Referenced documents. In addition to MIL-DTL-26482, this document

10、 references the following: ASME Y14.5M CONCLUDING MATERIAL Custodians: Preparing activity: Army CR DLA CC Navy AS Air Force 85 (Project 5935-2007-180) DLA CC Review activities: Army AR, AV, MI Navy EC, SH Air Force 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-