DLA MS14305 REV C-2009 FITTINGS PIPE BRASS OR BRONZE THREADED (TEES CROSSES 45-DEG ELBOWS AND COUPLINGS) CLASS 125.pdf

《DLA MS14305 REV C-2009 FITTINGS PIPE BRASS OR BRONZE THREADED (TEES CROSSES 45-DEG ELBOWS AND COUPLINGS) CLASS 125.pdf》由会员分享，可在线阅读，更多相关《DLA MS14305 REV C-2009 FITTINGS PIPE BRASS OR BRONZE THREADED (TEES CROSSES 45-DEG ELBOWS AND COUPLINGS) CLASS 125.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、F W B G D W B H A A A A A A A E C C DETAIL SPECIFICATION SHEET FITTINGS, PIPE, BRASS OR BRONZE, THREADED (TEES, CROSSES, 45-DEG. ELBOWS, AND COUPLINGS), CLASS 125 This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the p

2、roduct described herein shall consist of this specification sheet and WW-P-460. U V X YC YW TEE CROSS 45 DEG ELBOW CAST COUPLING WROUGHT COUPLING FIGURE 1. Elbows, tees, crosses and coupling fittings. AMSC N/A FSC 4730 INCH-POUND MS14305C 15 December 2009 SUPERSEDING MS14305B 28 February 1994 Provid

3、ed by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS14305C 2 Fitting type and size applicability. NOTES: 1. Metric equivalents are given for information only. 2. Material: Brass or bronze in accordance with ASME-B16.15. 3. Protective Coating: None 4. Dimensi

4、ons: In accordance with ASME-B16.15, table titled “Dimensions of 90-deg Elbows, Tees, Crosses, 45-deg Elbows, and Couplings. (Straight Sizes) Class 125”. 5. Thread: As specified in ASME-B16.15. 6. Marking: In accordance with ASME-B16.15. 7. Part or Identifying Number (PIN): The MS PIN consists of th

5、e MS number, the dash number, and the fitting Identification letter(s). When left-hand threads are required, add the letter “L” to the PIN. FIGURE 1. Elbows, tees, crosses and coupling fittings Continued. PIN: MS 14305 -3 X L Examples: MS14305 6V represents a 1 NPS cross. MS14305 5XL represents a 3/

6、4 NPS 45-deg elbow, left-hand threads. MS14305 2YC represents a 1/4 NPS cast coupling. Dash number Pipe size mm Tee U Cross V 45-Deg elbow Cast coupling YC Wrought coupling YW - 1 - 2 - 3 - 4 - 5 - 6 - 7 - 8 - 9 - 10 - 11 - 12 1/8 (.125) 1/4 (.250) 3/8 (.375) 1/2 (.500) 3/4 (.750) 1 (1.000) 1-1/4 (1

7、.250) 1-1/2 (1.500) 2 (2.000) 2-1/2 (2.500) 3 (3.000) 4 (4.000) 3.18 6.35 9.53 12.70 19.05 25.40 31.75 38.10 50.80 63.50 76.20 101.60 X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X . . . . . . . MS prefix Basic specification number Dash numb

8、er on figure 1 Outside head, inside head, face designator, see figure 1 Thread designator: Blank right hand thread, L- left hand thread Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS14305C 3 Changes from previous issue. Marginal notations are not

9、 used in this revision to identify changes with respect to the previous issue, due to the extent of the changes. Referenced documents. In addition to WW-P-460, this document references the following: ASME-B16.15 CONCLUDING MATERIAL Custodians: Preparing activity: Army - AT DLA - CC Navy - MC Air For

10、ce - 99 DLA - CC (Project 4730-2009-003) Review activities: Army - AR, CE, EA Navy SA, SH, YD Air Force - 71 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-