DLA MIL-S-87021 B-1985 SHIRT DISPOSABLE [Use GSA A-A-50390 A GSA A-A-50390]《用完即弃衬衣》.pdf

《DLA MIL-S-87021 B-1985 SHIRT DISPOSABLE [Use GSA A-A-50390 A GSA A-A-50390]《用完即弃衬衣》.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-S-87021 B-1985 SHIRT DISPOSABLE [Use GSA A-A-50390 A GSA A-A-50390]《用完即弃衬衣》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、, . 23 January 1985 SUPERSEDING MIL-S-8702l.A( SA) i 12 January 1979 MILITARY SPECIFICATICN SHIFX, DISPOSABLE This specification is approved for use by the Navy Clothing and Textile Research Facility, Department of the Navy, and is available for use by all Departments and Pgencies of the Department

2、of Defense. 1. SCOPE 1.1 Scope. This speFification covers the requirements for a disposable shirt. 1.2 Classification. The shirt covered by this specification. shall be of one type and in the following sizes (see 6.2): X-Small wall Medium Large X-Large XX-Large 2. APPLICABLE WCUMENTS 2.1 Government

3、documents. Beneficial camnents (recannendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Officer in Charge, Navy Clothing and Textile Research Facility, 21 Strathore bad, Natick MA 01760-2490 by using the self-addressed Stan

4、dardization Docmnt Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. - - FSC 8415 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-8702LB 4 W 777770b 04iiLbbO 5 4 MIL-S-87021B(NUj 2.1.1 Specifications, stand

5、ards, and handbooks. Unless otherwise specified, the following specifications, standards, and handbooks of the issue listed in thae. issue of-the Cepartment of. Defense Index of Specifications and Standards (DODISS) specified in the solicitation form a part of this specification to the extent specif

6、ied. SPECIFICATIONS MILITARY MIL-B-17757 - Boxes Shipping, Fiberboard (Modular Sizes) MIL-C-87019 - Cloth. Nonmven, Disposable. Spunbonded Olefin (Coated and Uncoated) STANDARB3 FEDERRL FED-STE-751 - Stitches, Seams, and Stitchings M I LITARY MIL-STD-105 - Sampling Procedures and Tables for Inspecti

7、on MIL-STE-129 - Marking for Shipnent and Storage MIL-STD-147 - Palletize Unit Loads Attributes (Copies of specifications, standards, drawings, and publications required contractors in connection with specific procurement functions should be obtained from the procuring activity or as directed by the

8、 contracting officer. ) bY Y 2.1.2 Other Govenmient documents, drawings, and publications. The following other Government docmnts, drawinas, and mblications form a part of this specificatn to the extent specifi2 herein LAWS AND-REGULATIONS- U FOSTAL SERVICE i4ANUm (Copies of the manual may be obtain

9、ed fran the Superintendent of hmnts, US Govert-gent P 8415-00-000-0000 ( X-Large (Example) NAME OF CONTRACTOR: CAUTION: THIS GARMENT SHALL NOT BE REUSED AND MUST BE DISCARDED WHEN (YI“ FUEL STAINS ARE! OBSERVED. * 3.4 Design- full-length set in one or two piece sleeves. a sewn-on collar and a full f

10、ront opening secured by 5 plastic snap fasteners. shall he of white polyethylene coated spun bonded olefin material and the back shall be of uncoated spun bonded olefin material. material is to be considered the face side. The shirt shall be a below-the-hips length style, have The collar, front and

11、sleeves The coated side of the . 3.4.1 Figure. The figure is furnished for information purposes only. To the extent of any inconsistencies between the written specification and the figure, the written specification shall govern. 3.5 Patterns. Standard patterns to be used for cutting working patterns

12、 will be furnished by the Government (see 6.3). The patterns allow 3/8 to 1/2 inch for all seams. Neither the Government patterns nor the working patterns shall be altered in any way. * 3.5.1 List of pattern parts. The canponent parts of the shirt shall be cut fran the materials specified and in acc

13、ordance with the pattern parts required for the manufacturing process as follows Ma ter ia1 Ncmenclature of pattern parts Cut parts Cloth, Nonwoven, Back 1/ 1 - Ferforated, Typ I Cloth, Nonwoven, Coated, Wont 2- Nonperforate, Type II . Sleeve - 2/ 4. Collar 1 - i/ This park may be cut into two piece

14、s with a 3/8 to 1/2 inch sem allowance added. . - 2/ This part may be .cut as one piece. i4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-t MIL-S-7021B 4 7777906 044libb3 O MIL-S-87021B( NU) t 3.6 Construction. 3.6.1 Stitch, seam and stitching tms-

15、. types specified herein shall confmn to FED-STD.751 specified herein, the seam tm shall be SSp or SSn-1 used with any 500 stitch type (except 501, 510, 511, or 513) or lsc-2 with 301 or 401 stitch type. The stitch, seams and stitching Unless otherwise 3.6.2 Stitches per inch. The minhm and maximum

16、number of stitches per inch shall be 6 and 8 respectively. 3.6.3 Thread breaks and ends of seams. he ends of a continuous line of A 1/4 to 1/2 inch of stitching shall be overlapped not less than 1/2 inch. stitching chain shall remain at the end of the sleeve and side seams to prevent raveling stitch

17、ing not less than 1/2 inch beyond each end of the defect using the 301 stitch. Skipped stitches and thread breaks shall be repaired by 3.7 Manufacturing operations requirements; The shirts shall be manufactured in accordance with the operatian requirements specified in Table I. The contractor is not

18、 required to follow the exact sequence of operations listed pravided that the finished shirts are identical to those produced by following the sequence as shm. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-8702LB 4 79997Ob OLi4Lbb4 2 f MIL-S-

19、8?021B( Nu) TABLE 1 - CONSTRUCTION OF SHIW 4 Tfiread Stch Ndl Bob/ in Lp No. peration Stch Sam/ Stch type 1. Cutting. The shirt shall be cut in strict accordance with the Government patterns furnished which show size, shape, directional lines for cutting, and notches for proper assembly of all parts

20、. The face side of the coated basic materizl to be assembled shall be the coated side. 2. Replacement of defective canponents During the spreading, cutting and manufacedring process, canponents having material defects or damages that are . classified as defects in Section 4 shall be removed from pro

21、duction and replaced with non-defective and properly matched canponents. 3. Marking All Darts shall be marked or bundled to insure proier assembly of the shirt. The use of metal devices, sew-on tickets or drill holes is not permitted. 4. Make shirt a. Stitch two-piece sleeves together face to face t

22、o form outseam. - b. Join fronts to back at shoulders face to face. c. shirt. Insert sleeves and join sleeves to body of P Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-8702LB 4 7777906 0441665 4 W MIL-S-87021B(NU) TABLE 1 - CONSTRUCTION OF S

23、HIRT Thread . Stch seam/ Stch Ndl Bob/ Stch type in Lpr . _. No. -ration d. Form facing and attach five (5) socket parts w/prong backing on the left front and five (5) stud parts w/prong backing on the right front where indicated by marks on pattern . NOTE: As an alternate, the center of the top sna

24、p fastner shall be positioned 1/4 to 3/8 inch from the top of the neckline, The remaining snap fasteners shall be spaced equidistant, 5 1/2 + 1/4 inches on center foir all sizes. The disGnce fran the folded edges of the facing shall be the same as that indicated by patterns. e. with the illegible; o

25、f improper size location secpence or method of application. Any component missing. damaged, or not as specified. Inadequate application of canpnents, such as: Incomplete closure of container flaps, improper Bulged or distorted container. , taping loose strapping, or inadecpate stapling. Number of sh

26、irts per shipping container is more or less than specified. io Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-8702LB 8Li W 777770b 04Lilbb7 L MIL-S-87021B 4.4.4 Palletization examination. An examination shall be made to determine that the pall

27、etization canplies with the section 5 requirements. Defects shall be scored in accordance with .the .list below. The sample unit shall be one palletized unit load fully packaged- The lot size shall be the number of palletized unit loads in the end item inspection lot. The inspection level shall be S

28、-1 and the AQL, expressed in tem of defects per hundred units, shall be 6.5. Examine kfect Finished dimensions Palletization Length, width, or height exceeds specified maximum requireiwnts . Pallet pattern not as specified. Interlocking of loads not as specified. had not bonded with required straps

29、as specif ied. Weight Exceeds maximum load limits. Marking 5. PACKAGING Qnitted; incorrect; illegible; of improper size - location, sequence - or method of application. 5.1 Preservation-packaging. Packaging shall be level A or C (See 6.2). 5.1.1 Level A. Each shirt shall be folded to measure approxi

30、mately 14 by 11 inches. 5.1.2 Level C (Ccmnercial Packaging). me shirts shall be packaged to afford adequate protection against physical damage during shipnt fran the contractor to the first receiving activity. The package and the quantity per package shall be the same as that normally used by the c

31、ontractor for retail distribution. 5.2 Packing. 5.2.1 Level A. Eighty (80) shirts of one size only, packaged as specified in 5.1, shall be packed in a fiberboard shipping container assembled, closed and reinforced conforming to type CF class weather-resistant, variety Dw, grade VlSc, size 3A of MIL-

32、B-17757. The fiberboard for the box liner shall conform to-tw CF, class danestic, of MIL-B-17757. ievel A packages shall be packed flat, two in length, one in width, and forty in depth within a shipping container, Each container shall have the contents ccmpletely covered on the top and bottm with a

33、sheet of carniercial grade kraft paper. Toward the end of the contract or when there are less than the required amount per container of the same size, mixed sizes may be packed within the same container. Packing shall be level A, B, or C (see 6.2). 11 I Provided by IHSNot for ResaleNo reproduction o

34、r networking permitted without license from IHS-,-,-MIL-S-702LB 4 W 777770b 0443670 c MIGS-87021B i 5.2.2 Level B. Eighty (80) shirts of one size only, packaged as specified in 5.1, shall be packed in a fiberboard shipping container assembled, closed and kinforced conforming to type CF, class dcmest

35、ic,variety W, grade 275, size 3A of MIL-B-17757. The fiberboard for the box liner shall conform to type CF, class danestic of MIL-B-17757. &vel A packages shall be packed flat, two in length, one in width, and forty in depth within a shipping container. Each container shall have the contents complet

36、ely covered on the top and bottom with a sheet of carniercial grade kraft paper. Toward the end of the contract or when there are less than the required amount per container of the same size, mixed sizes may be packed within the same container- 5.2.3 Level C (Ccmnercial Packing). Shirts, packaged as

37、 specified in 5-1, shall be packed in a manner to insure carrier acceptance and safe delivery at destinatin at the lowest transportation rate for such supplies. The quantity per shipping container shall be the same as that normally used by the supplier for retail distribution. Containers shall canpl

38、y with the U.S. Postal Service Manual, Uniform Freight Classification Ihiles or National Motor Freight Classification Rules, as applicable. 5.3 Markinq. In addition to any special marking required by the contract or order, shipping containers shall be marked in accordance with MIL-STD-129. . 5.3.1 L

39、abels, mixed sizes. Each shipping container, packed with mixed sizes only. shall have securely attached to the end and side, directly under the printing or stenciling, a white paper label 5 by 4 inches with the words “MIXED SIZES“ plainly stamped or printed thereon and under these words shall be leg

40、ibly stamped or printed the correct quantity and sizes contained herein. 5.4 Palletization. When specified (see 6.2) (shirts), packed as specified in 5.2, shall be palletized in accordance with load type I of MIL-STD-147. Each prepared load shall be bonded with primary and secondary straps in accord

41、ance with the bonding means K and L or bonding means O. Pallet patterns shall be in accordance with the appendix of MIL-STD-147. Interlocking of loads shall be effected by reversing the pattern of each course. If the container is of a size which does not conform to any of the patterns specified in M

42、IL-STD-147, the pallet pattern used shall first be approved by the contracting officer. 6. NOTES 6.1 Intended use. The shirt is intended primarily for use as part of an ensemble used to protect torpedo handlers from exposire to Otto fuels. 6.2 Ordering: data. Procurement docianents should specify th

43、e following: a. b. Sizes required (see 1.2). c. d. e. Title, number.and date of this specification. First. article reqdirements , (see 3.2) . Selection of the applicable levels of packaging and packing (see 5.1 When palletization is required (see 5.4). and 5.2). Provided by IHSNot for ResaleNo repro

44、duction or networking permitted without license from IHS-,-,-MIL-S-87021B 4 MIL-S-87021B m 7777706 044Lb71 T . 6.3 Samples For access to samples, address the procuring activity issuing the invitation for bids 6.4 Snap fasteners. The snap fastener cmponents numbered 66-4100-00-00-6200, 66-4200-00-00-

45、6200, and 66-4300-00-00-6200 are manufactured by Scovill Inc., %?arel Fastener Division, 500 Fifth Avenue, New York, N.Y. 10110. ATI“: Govennnent Sales 6.5 “Or Equalg1 items Prior to the use of an “or equal“ item, the contract= shall suhit the item with supporting data to the contracting officer for

46、 subsequent approval or disapproval by the responsible Military Agency. Custodian : Navy - Nu Review activities: Navy - SH, OS DLA - CT Preparing Activity Navy - Nu Project W. 8415-0333 . 13 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I 14 F RONT U.O. OOVERNMENT PRINTINB OFFICE: 198s - 505-038120777 -r . : Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-