DLA MIL-PRF-8805 114 D-2012 SWITCH ASSEMBLY SENSITIVE ROLLER PLUNGER SPDT 7 AMPERES WATERTIGHT SEAL.pdf

《DLA MIL-PRF-8805 114 D-2012 SWITCH ASSEMBLY SENSITIVE ROLLER PLUNGER SPDT 7 AMPERES WATERTIGHT SEAL.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-PRF-8805 114 D-2012 SWITCH ASSEMBLY SENSITIVE ROLLER PLUNGER SPDT 7 AMPERES WATERTIGHT SEAL.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 5930 INCH-POUND MIL-PRF-8805/114D 6 December 2012 SUPERSEDING MIL-PRF-8805/114C 4 October 2004 PERFORMANCE SPECIFICATION SHEET SWITCH ASSEMBLY, SENSITIVE, ROLLER PLUNGER, SPDT, 7 AMPERES, WATERTIGHT SEAL This specification is approved for use by all Departments and Agencies of the Depar

2、tment of Defense. The complete requirements for acquiring the switches described herein shall consist of this specification and the latest issue of MIL-PRF-8805. FIGURE 1. Dimensions and configuration. SEE NOTE 8 0.120 MIN DIA OR EQUIVALENT LOCKWASHER, INTERNAL TOOTH NASM 35333-326 OR EQUIVALENT NEM

3、A-HP3 NEMA-HP3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-8805/114D 2 LESS MOUNTING HARDWARE AND DECAL FIGURE 1. Dimensions and configuration - Continued. DETAIL OF MOUNTING PLATE, 0.100 THICK Provided by IHSNot for ResaleNo reproduction

4、 or networking permitted without license from IHS-,-,-MIL-PRF-8805/114D 3 Inches mm Inches mm 0.003 0.08 0.375 9.53 0.004 0.10 0.42 10.67 0.005 0.13 0.433 11.00 0.010 0.25 0.443 11.25 0.015 0.38 0.45 11.43 0.025 0.64 0.469 11.91 0.03 0.76 0.470 11.94 0.031 0.79 0.480 12.19 0.059 1.50 0.56 14.22 0.06

5、 1.52 0.64 16.26 0.065 1.65 0.72 18.29 0.072 1.83 0.83 21.08 0.090 2.29 0.87 22.10 0.100 2.54 0.93 23.62 0.120 3.05 0.906 23.01 0.125 3.18 1.00 25.40 0.164 4.17 1.56 39.62 0.22 5.59 1.812 46.02 0.26 6.60 2.00 50.80 0.36 9.14 2.25 57.15 7.00 177.80 NOTES: 1. Dimensions are in inches. 2. Metric equiva

6、lents are given for general information only. 3. Unless otherwise specified, tolerance (in inches) is 0.03 for 2 place decimals and 0.005 for 3 place decimals. 4. Exact shape of switch optional within envelope dimensions shown. 5. Mounting plate shall be positioned between indicated dimensions. 6. D

7、ecal: Pressure sensitive, aggressive tack type, using permanent adhesive. 7. Alternative base metals and protective finishes, as approved by the qualifying activity, may be utilized for hardware material. 8. Lead wire shall be 20 gauge, flame and abrasion, insulated black and shall be capable meetin

8、g the environmental and system requirements of the intended application. FIGURE 2. Dimensions and configuration - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-8805/114D 4 REQUIREMENTS: Dimensions and configuration: See figures 1

9、. Enclosure design: 3. Temperature characteristic: 1. Shock type: M. Sinusoidal vibration grade: 2. Military part number: M8805/114-01. Finish: All exposed parts shall be corrosion resistant or shall be treated for corrosion resistance. Mounting hardware: Mounting plate shall be positioned as shown

10、on figure 1. Weight (with leads): 0.20 pound maximum. Operating characteristics: Actuating force: 9 3 pounds. Releasing force: 4 pounds minimum. Pretravel: 0.040 inch maximum. Overtravel: 0.125 inch minimum. Overtravel force: 30 pounds maximum. Movement differential: 0.020 inch minimum. Strength of

11、actuating means: 30 pounds. Salt spray: Connectors shall be coupled during the test and examined for corrosion following the test. Sand and dust: Connectors shall be coupled during the test. Following the test, there shall be no evidence of dust inside the connectors. Mechanical endurance: 25,000 cy

12、cles. Electrical endurance: 25,000 cycles. Electrical ratings: See table I. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-8805/114D 5 TABLE I. Electrical ratings. Load Sea level 28 V dc (amperes) Resistive 7 Inductive 4 Motor 4 Marking: Bla

13、ck printing 0.06 inch high on white background (decal). Terminal identification: Include circuit schematic diagram. Qualification inspection: Table II applies only if qualified MIL-PRF-8805/4 basic sensitive switches are utilized, and similar products have been qualified to MIL-PRF-8805/43 or MIL-PR

14、F-8805/104. TABLE II. Qualification inspection. Number of sample units Tests of MIL-PRF-8805 qualification inspection table 6 Group I 2 Group III 4 1/ Group VII 1/ Electrical endurance: Only resistive and inductive loads need to be tested Changes from previous issue. The margins of this specificatio

15、n are marked with vertical lines to indicate where modifications from this revision were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this do

16、cument based on the entire content irrespective of the marginal notations. Referenced Documents: MIL-PRF-8805 MS25082 MIL-PRF-8805/4 MS27144 MIL-PRF8805/43 NASM 35333 MIL-PRF-8805/104 NEMA-HP3 Custodian: Preparing activity: Army - AT DLA - CC Air Force - 85 DLA - CC (Project 5930-2011-115) Review ac

17、tivities: Air Force - 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil/ . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-