DLA MIL-PRF-64266 10 A-2012 CONNECTORS FIBER OPTIC CIRCULAR PLUG STYLE MULTIPLE REMOVABLE TERMINI DUST COVER SCREW THREADS ENVIRONMENT RESISTING.pdf

《DLA MIL-PRF-64266 10 A-2012 CONNECTORS FIBER OPTIC CIRCULAR PLUG STYLE MULTIPLE REMOVABLE TERMINI DUST COVER SCREW THREADS ENVIRONMENT RESISTING.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-PRF-64266 10 A-2012 CONNECTORS FIBER OPTIC CIRCULAR PLUG STYLE MULTIPLE REMOVABLE TERMINI DUST COVER SCREW THREADS ENVIRONMENT RESISTING.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、 MIL-PRF-64266/10A 10 January 2012 SUPERSEDING MIL-PRF-64266/10 25 November 2008 PERFORMANCE SPECIFICATION SHEET CONNECTORS, FIBER OPTIC, CIRCULAR, PLUG STYLE, MULTIPLE REMOVABLE TERMINI, DUST COVER, SCREW THREADS, ENVIRONMENT RESISTING This specification is approved for use by all Departments and A

2、gencies of the Department of Defense. The requirements for acquiring fiber optic connectors described herein shall consist of this specification sheet and MIL-PRF-64266. Dust covers for MIL-PRF-64266 receptacles shall be in accordance with MIL-PRF-64266/11. FIGURE 1. Plug dust cover. AMSC N/A FSC 60

3、60 INCH-POUND Inches mm .450 11.43 .630 16.00 .670 17.02 1.000 25.40 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-64266/10A 2 Shell size T thread Class 2A A dia max B dia C dia inside 6/ 7/ D dia outside 6/ 7/ E dia outside Inches mm Inche

4、s mm Inches mm Inches mm Inches mm 11 .750-.1P- .2L-D.S. 1.028 26.11 .581 .569 14.75 14.45 .125 .110 3.17 2.79 .210 .170 5.44 4.32 .606 .600 15.6 15.0 13 .875-.1P- .2L-D.S. 1.141 28.98 .705 .693 17.90 17.60 .733 .710 18.6 18.0 15 1.062-.1P- .2L-D.S. 1.263 32.08 .877 .865 22.27 21.97 .890 .870 22.6 2

5、2.0 23 1.500-.1P- .2L-D.S. 1.705 43.26 1.299 1.287 32.99 32.69 .152 .173 3.87 3.48 .280 .240 7.11 6.10 1.36 1.33 34.6 34.0 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Dimensions apply to plated/finished part. 4. The connector plug interface di

6、mensions shall be in accordance with figure A-1 of MIL-PRF-64266. 5. Optional configuration (see PIN). For attachment to solid backshell, use cable loop. For attachment to split backshell, use fastener. 6. Fastener hole diameter is sized for captive screws fastened using a 3/32 inch (2.38 mm) hex wr

7、ench for shell sizes 11, 13, and 15. 7. Fastener hole diameter is sized for captive screws fastened using a 7/64 inch (3.57 mm) hex wrench for shell size 23. FIGURE 1. Plug dust cover - Continued. REQUIREMENTS: Dimensions and configurations: See figure 1 herein and MIL-PRF-64266, figure A-1. Weight:

8、 Weight shall not exceed the specified value in table I for the applicable shell size. Weight includes lanyard and ring. TABLE I. Dust cover weights. Shell size Composite Aluminum Stainless steel ounces grams ounces grams ounces grams 11 0.28 8.0 0.49 14.0 1.27 36.0 13 0.35 10.0 0.56 16.0 1.59 45.0

9、15 0.42 12.0 0.71 20.0 1.94 55.0 23 0.63 18.0 1.06 30.0 3.17 90.0 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-64266/10A 3 Qualification: Qualification shall consist of performing testing specified as listed in table II. The tests in this

10、initial qualification table are applicable when performed only for the dust covers. When testing the connector plug and connector receptacle, the dust cover shall be included as part of the initial qualification of these components and not tested separately. In either case, the dust cover shall meet

11、 the requirements for the same inspections as listed in table II. Table II. Qualification inspections Test performed 7/, 11/ Initial For change in qualification Seal material Sealing integrity Plating Shell size Lanyard 1/ 2/ 3/ 4/ 5/ 6/ GROUP 1 (6 mated pairs) Interoperability (not applicable) Visu

12、al & Mechanical Size X X X Weight X X X Identification marking X X X Screw threads X X Workmanship X X X X X X Functional Connector coupling engagement and disengagement torque X X X X X Dust cover mating durability X X X X Connector coupling engagement and disengagement torque X X X X Water pressur

13、e 14/ X X X X Optical None GROUP 2 (2 mated pairs) Backshell-to-connector mating torque Cable pull out force (retention) External bending moment Cable seal flexing Twist Impact X X X Crush X X X Vibration: Swept sine Vibration: Random Shock: MIL-S-901 12/ X X Water pressure 14/ X X Modified SO2/salt

14、 spray X X X X X Connector coupling engagement and disengagement force X X X X X Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-64266/10A 4 Table II. Qualification inspections Continued. Test performed 7/, 11/ Initial For change in qualifica

15、tion Seal material Sealing integrity Plating Shell size Lanyard 1/ 2/ 3/ 4/ 5/ 6/ GROUP 3 (2 mated pairs) Thermal shock X X X X Temperature/humidity cycling Temperature cycling Life aging (Temperature X X X X Freezing water Sand & dust X X X X Identification marking X X X Connector coupling engageme

16、nt and disengagement torque X X X X Water pressure 14/ X X X X Group 4 (2 mated pair + parts) 7/ Electromagnetic effects (2 mated pair) 9/ 13/ X X Fluid immersion (2 mated pair) X X X X Shell to shell conductivity (initial) X X Salt spray (2 mated pair) 8/ X X X Shell to shell conductivity (post sal

17、t spray) X X Connector coupling engagement and disengagement torque X X X Flammability (1 mated pair) Fungus resistance (parts) 10/ X X X Ozone exposure (parts) 10/ X X X 1/ Test sample configuration. Unless otherwise specified, the connector plug dust cover shall be mated to the connector receptacl

18、e dust cover for each of the tests/inspections. When testing the connector plug and connector receptacle as part of the initial qualification, one end of each dust cover lanyard shall be affixed to the connector. 2/ Seal material. Tests in this column may be excluded if other components that use the

19、 same seal material are qualified to this defense specification. 3/ Seal integrity. These tests verify the sealing integrity, verify aspects unique to the dust cover configuration, and so shall be performed as part of a dust cover qualification for a change in seal material or dust cover design. 4/

20、Plating. Tests in this column other than those for group 1 visual and mechanical inspection may be excluded if other components that use the same plating are qualified to this defense specification with one provision: The other components must contain the same knurl or other style gripping surface a

21、s dust covers being qualified. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-64266/10A 5 Table II. Qualification inspections Continued. 5/ Shell size. With the exception of those tests listed in group 1, tests in this column can be excluded

22、 for smaller shell sizes once dust covers for larger shell sizes are qualified to this defense specification. 6/ Lanyard attachment. Lanyard attachment shall consist of a coated stainless steel wire rope with ring. This column applies when a material or configuration (such as attachment method to du

23、st cover) is changed. 7/ Group 1 mated pair are to be used for Groups 2 and 3 tests. Group 4 may be performed before Group 1, and, except for electromagnetic effects, with separate samples. 8/ Salt spray. Two options: a. Use same two mated pair from the fluid immersion test. b. Use separate mated pa

24、ir. 9/ Electromagnetic effects. Two (2) mated pair from the fluid immersion, salt spray, or Group 2/3 samples after that Groups test completion may be used. 10/ Parts only, assembly not required. 11/ Specific test practices for physical, mechanical, environmental and material tests, including clarif

25、ications and further details, are found in MIL-STD-1678-3. 12/ Shock test. Mated dust covers shall be affixed to standard shock fixture 4A for bulkhead mounting in the same manner as the dust covers are affixed to the connector. There shall be no damage or loosening of parts and mated dust covers sh

26、all not become a missile hazard. 13/ For receptacle dust cover only. Two of the six mated pair from Group 1 shall be used. Test sample configuration shall consist of a receptacle dust cover mated to a connector receptacle. 14/ Water pressure. When test is performed with a dust cover mated to a conne

27、ctor and the dust cover is removed for the post test water penetration inspection, orient the connector so that it is facing away from the center of the earth. This orientation will prevent water that may have penetrated threads prior to seals from entering the connector (resulting in a false positi

28、ve for water penetration). Maintenance aging: Not applicable. Twist: Not applicable. Mating durability: Not applicable. Dust cover mating durability: Dust covers shall be mated then de-mated for 500 cycles to the applicable connector plug or connector receptacle. Dust cover seals shall not be render

29、ed unfit for sealing (as determined by no wear, no displacement, and no penetration after the succeeding water pressure test). Threads shall not exhibit signs of wear. Plating shall remain intact to extent that dust cover can be mated and de-mated after performance of sand and dust and after salt sp

30、ray. Water pressure: Applicable except immerse in fresh water to equivalent depth of 3 feet (0.9 m) for a period of 30 minutes. Next, the dust covers shall be removed, externally cleaned and dried, and visually examined for water penetration into each dust cover. No water penetration past the sealed

31、 surfaces of the dust cover interior shall occur. Gasket: Gasket shall be bonded to cover or mechanically retained. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-64266/10A 6 Lanyard: Lanyard shall be free to rotate on fastener affixed to du

32、st cover. A fastener shall be affixed to other end of lanyard for dust covers to be used with split backshells. A cable loop shall be affixed to other end of lanyard for dust covers to be used with solid backshells and other configurations without screw retention availability. Lanyard attachment sha

33、ll consist of a coated stainless steel wire rope with fastener or with cable loop. The inside diameter of the cable loop at a right angle to the crimp sleeve shall meet the values specified for dimension C (see figure 1). Marking: Part or Identification Number (PIN): Marked dust cover. M64266/10 X X

34、 X Basic PIN Shell size designator letter B = Shell size 11 C = Shell size 13 D = Shell size 15 H = Shell size 23 Material designator letter A = Aluminum with cadmium electrolytic compatible plating B = Composite with cadmium electrolytic compatible plating C = Stainless steel, passivated Lanyard at

35、tachment designator number 1 = Lanyard with fastener (for split backshells with screw available for retention) 2 = Lanyard with cable loop (for solid backshells) PIN example: M64266/10BA2 Changes from previous issue: The margins of this specification sheet are marked with vertical lines to indicate

36、where changes from the previous issue were made. This is done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of the document based on the entire contents irrespective

37、 of the marginal notation and relationship to the last previous issue. Referenced documents. In addition to MIL-PRF-64266, this specification sheet references the following document: MIL-PRF-64266/11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MI

38、L-PRF-64266/10A 7 Custodians: Preparing activity: Army - CR DLA - CC Navy - SH Air Force - 85 (Project 6060-2011-010) DLA - CC Review activities: Army - MI Navy - AS Air Force - 13, 19, 93, 99 NASA - NA NOTE: The activities listed above were interested in this document on the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-