DLA MIL-PRF-39012 73 C-2011 CONNECTORS PLUGS ELECTRICAL COAXIAL RADIO FREQUENCY SERIES SMC (CABLED SOCKET CONTACT CLASS 2).pdf

《DLA MIL-PRF-39012 73 C-2011 CONNECTORS PLUGS ELECTRICAL COAXIAL RADIO FREQUENCY SERIES SMC (CABLED SOCKET CONTACT CLASS 2).pdf》由会员分享，可在线阅读，更多相关《DLA MIL-PRF-39012 73 C-2011 CONNECTORS PLUGS ELECTRICAL COAXIAL RADIO FREQUENCY SERIES SMC (CABLED SOCKET CONTACT CLASS 2).pdf（11页珍藏版）》请在麦多课文档分享上搜索。

1、INCH-POUND MIL-PRF-39012/73C 16 November 2011 SUPERSEDING MIL-PRF-39012/73B 24 September 1986 PERFORMANCE SPECIFICATION SHEET CONNECTORS, PLUGS, ELECTRICAL, COAXIAL, RADIO FREQUENCY, SERIES SMC (CABLED, SOCKET CONTACT, CLASS 2) This specification is approved for use by all Departments and Agencies o

2、f the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-PRF-39012. NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. For dimension A, see table I. 4. Dimension A defines the

3、overall length of the connector when assembled to the cable. 5. Wrench flats are to accommodate standard wrench opening in accordance with FED-STD-H28, appendix 10. 6. Maximum overall diameter of the connector is .320 inch (8.13 mm). 7. All undimensioned pictorial configurations are for reference pu

4、rposes only. 8. Series SMC, socket contact interface in accordance with MIL-STD-348. FIGURE 1. General configuration. AMSC N/A FSC 5935 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-39012/73C 2 TABLE I. Dash numbers, cross-reference, and di

5、mensions. Dash No. M39012/73- # Applicable cable group from MIL-PRF-39012, appendix B M17/ Typical mating connector 1/ Dimensions Inches (millimeters) maximum 2/ CATEGORY A FIELD SERVICEABLE (NO SPECIAL TOOLS REQUIRED) 0003 3/ 4/ Cable group I 93-RG178 * 169-00001 % M39012/74-0003 M39012/76-0003 A .

6、88 (22.35) 0004 3/ 4/ Cable group II 113-RG316 * 172-00001 % 94-RG179 M39012/74-0004 M39012/76-0004 0103 3/ Cable group I 93-RG178 * 169-00001 % M39012/74-0103 M39012/76-0103 0104 3/ Cable group II 113-RG316 * 172-00001 % 94-RG179 M39012/74-0104 M39012/76-0104 4101 3/ Cable group I 93-RG178 * 169-00

7、001 % M39012/74-4101 M39012/76-4101 4102 3/ Cable group II 113-RG316 * 172-00001 % 94-RG179 M39012/74-4102 M39012/76-4102 CATEGORY C FIELD REPLACEABLE (MIL-C-22520/5 BASIC CRIMP TOOL) 5/ 0011 3/ 4/ Cable group I 93-RG178 * 169-00001 % M39012/74-0011 M39012/76-0011 A 1.10 (27.94) 0012 3/ 4/ Cable gro

8、up IIa Example: M39012/73-3001 mates with M39012/74-3001, and M39012/73-4001 mates with M39012/74-4001. NOT FOR ARMY, NAVY, OR AIR FORCE USE. FOR OEM USE ONLY Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-39012/73C 10 TABLE V. Group qualifi

9、cation and retention testing. Group Submission and retention of qualification of any of the following connectors 1/ M39012/ Qualifies the following connectors M39012/ I 73-0003 73-0003 73-0103 2/ II 73-0004 73-0004 73-0104 2/ III 73B0008 73B0008 73B0013 2/ IV 73B0009 73B0009 73B0010 73B0014 2/ 73B00

10、15 2/ V 73B0010 73B0010 73B0015 2/ VI 73-0011 73-0011 73-0016 2/ VII 73-0012 73-0012 73-0017 2/ 1/ For qualification retention, where more than one part is listed in a group in this column, data may be supplied on any of those parts in order to retain qualification for those parts in the correspondi

11、ng right hand column. 2/ Corrosion and contact resistance test data must be submitted to DSCC-VQ before qualification approval may be granted. NOTE: If a connector manufacturer produces a connector which meets all the requirements for two or more connector PINs (within the same series), the manufact

12、urer may receive qualification approval for two or more connector PINs by qualifying the one connector. It is not necessary that such connectors be in the same group. Each connector, however, must be marked with its own appropriate PIN. For group qualification, the connectors must be of similar desi

13、gn. Qualification of connectors qualifies connectors of the same material and finish only. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-39012/73C 11 TABLE VI. Cross reference of PIN. Preferred PIN M39012/73 1/ Substitute for PIN Or type de

14、signation -0003 -0004 B0008 B0009 B0010 M39012/73-0001 M39012/73-0002 M39012/73-0008, M39012/73-0005 M39012/73-0009, M39012/73-0006 M39012/73-0010, M39012/73-0007 1/ The “B” PIN is required marking for connectors manufactured after 24 March 1987. The connectors that are in stock or distribution that

15、 were previously qualified and marked with the old PIN shall also be considered acceptable for Government use until stock is purged. (Applies to category “B” P/N change only; M39012/XXBXXXX). Changes from previous issue. The margins of this specification are marked with vertical lines to indicate wh

16、ere changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective

17、of the marginal notations and relationship to the last previous issue. Referenced documents. In addition to MIL-PRF-39012, this document references the following: MIL-STD-348 MIL-DTL-22520 MIL-C-22520/5 MIL-STD-202 ASTM B488 FED-STD-H28 CONCLUDING MATERIAL Custodians: Preparing activity: Army - CR D

18、LA - CC Navy - EC Air Force - 85 (Project 5935-2009-107) DLA - CC Review activities: Army - AT, AV, EA, MI Navy - AS, MC, OS, SA, SH Air Force - 19, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-