DLA MIL-PRF-23419 1 L-2012 FUSES INSTRUMENT TYPE STYLE FM01 (INDICATING).pdf

《DLA MIL-PRF-23419 1 L-2012 FUSES INSTRUMENT TYPE STYLE FM01 (INDICATING).pdf》由会员分享，可在线阅读，更多相关《DLA MIL-PRF-23419 1 L-2012 FUSES INSTRUMENT TYPE STYLE FM01 (INDICATING).pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、 AMSC N/A FSC 5920 INCH-POUND MIL-PRF-23419/1L 28 March 2012 SUPERSEDING MIL-PRF-23419/1K 21 June 2005 PERFORMANCE SPECIFICATION SHEET FUSES, INSTRUMENT TYPE, STYLE FM01 (INDICATING) This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements

2、 for acquiring the product described herein shall consist of this specification sheet and MIL-PRF-23419. Inches mm .039 0.99 .043 1.09 .142 3.61 .152 3.86 .17 4.3 .25 6.4 .27 6.9 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise spe

3、cified, tolerance is .02 (0.5 mm). FIGURE 1. Style FM01 fuses.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-23419/1L 2 REQUIREMENTS: Interface and physical dimensions: See figure 1. Applicable fuseholder: MIL-PRF-19207/26, type FHN42W. Case

4、 material: Ceramic. Terminals: Material: Brass. Finish: See table I. Strength: 9 pounds. Current rating, nominal: See table I. Voltage rating: See table I. Current carrying capacity: 100 percent (at all temperatures between -55C and +85C). Connecting wire shall be #14 and fuseholders shall not be sp

5、aced closer than 1 inch (25.4 mm) apart. Resistance: Not applicable. Overload interrupt: See table I. Short circuit interrupt: See table I. Shock: Method I for fuses rated 1/64A or less. Method II for fuses rated more than 1/64A. Thermal shock: Method 107 of MIL-STD-202, test condition B. Characteri

6、stic: See table I. Part or Identifying Number (PIN): The PIN is derived from table I and shall be as shown in table IV. Marking: Fuses shall be legibly and permanently marked with the manufacturers name or trademark and PIN designation. Style, voltage and amperage may be applied in separate rows, if

7、 required by space limitations or printing technique limitations. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-23419/1L 3 TABLE I. PIN designation identification. PIN designation Terminal finish Short circuit interrupt rating (amperes) Ove

8、rload interrupt time (seconds) 2/ Style Charac- teristic Maximum voltage Current rating Circuit voltage 1/ 200 percent nominal 300 percent nominal (amps) 28 volts 125 volts rating rating AC DC AC FM01 A 125V 1/200A Tin 3,000 3,000 60 .003 - .0004 .0005 - .0001 FM01 A 125V 1/100A plate .005 - .0008 .

9、0005 - .0001 FM01 A 125V 1/64A .001 - .0005 .0005 - .0001 FM01 A 125V 1/32A .006 - .001 .001 - .0003 FM01 A 125V 1/16A .050 - .010 .010 - .003 FM01 A 125V 1/10A .040 - .010 .010 - .004 FM01 A 125V 1/8A .050 - .010 .012 - .004 FM01 A 125V 2/10A .055 - .014 .012 - .005 FM01 A 125V 1/4A .040 - .014 .01

10、2 - .005 FM01 A 125V 3/10A .037 - .013 .012 - .005 FM01 A 125V 4/10A .042 - .015 .014 - .005 FM01 A 125V 1/2A .035 - .015 .015 - .005 FM01 A 125V 6/10A 1,500 1,500 .090 - .020 .018 - .008 FM01 A 125V 3/4A .090 - .020 .018 - .008 FM01 A 125V 1A .050 - .018 .018 - .008 FM01 A 125V 1-1/2A .050 - .020 .

11、020 - .008 FM01 A 125V 2A .060 - .020 .020 - .010 FM01 A 125V 3A .110 - .025 .023 - .010 FM01 A 125V 4A .300 - .040 .033 - .015 FM01 A 125V 5A .300 - .040 .033 - .015 1/ Alternating current - 60 Hz. 2/ The time ranges, as shown, cover the temperature range from -55 C through +85 C. Provided by IHSNo

12、t for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-23419/1L 4 Qualification and group C inspection: Inspection routine. The number of group II samples for qualification and subgroup 2 samples for group C inspection shall be as shown in table II. TABLE II. Group

13、II and subgroup 2 samples. Inspection Number of sample fuses Group II and subgroup 2 16 Terminal strength 4 Overload interrupt 200 percent at -55C 4 200 percent at +85C 4 300 percent at -55C 4 300 percent at +85C 4 The number of group III samples for qualification ( or first article ) and subgroup 1

14、 for group C testing shall consist of the number of sample units shown in table III. Short circuit interrupt tests shall be conducted at the voltage indicated, and the fuses shall be capable of withstanding a minimum short circuit current as shown in table III. TABLE III. Sampling for short circuit

15、qualification and group C tests. Current rating Short circuit current (amps) Number of sample (amps) 28 Volts 125 Volts units AC DC AC 1/200 3000 60 12 1/10 3000 12 1/8 1500 12 5 1500 60 12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-2341

16、9/1L 5 Supersession and cross reference: The superseding items include the requirements of the superseded items. The existing stocks of superseded items may be used. When exhausted, the superseding items shall be used ( see table IV ). TABLE IV. Cross-reference. Superseding PIN Superseded numbers FS

17、CM 81349 FSCM 81349 FM01A125V1/200A FM01-125V 1/200A M23419/1-001 FM01A125V1/100A FM01-125V 1/100A M23419/1-002 FM01A125V1/64A FM01-125V 1/64A M23419/1-003 FM01A125V1/32A FM01-125V 1/32A M23419/1-004 FM01A125V1/16A FM01-125V 1/16A M23419/1-005 FM01A125V1/10A FM01-125V 1/10A M23419/1-006 FM01A125V1/8

18、A FM01-125V 1/8A M23419/1-007 FM01A125V2/10A FM01-125V 2/10A M23419/1-008 FM01A125V1/4A FM01-125V 1/4A M23419/1-009 FM01A125V3/10A FM01-125V 3/10A M23419/1-010 FM01A125V4/10A FM01-125V 4/10A M23419/1-011 FM01A125V1/2A FM01-125V 1/2A M23419/1-012 FM01A125V6/10A FM01-125V 6/10A M23419/1-013 FM01A125V3

19、/4A FM01-125V 3/4A M23419/1-014 FM01A125V1A FM01-125V 1A M23419/1-015 FM01A125V1-1/2A FM01-125V 1-1/2A M23419/1-016 FM01A125V2A FM01-125V 2A M23419/1-017 FM01A125V3A FM01-125V 3A M23419/1-018 FM01A125V4A FM01-125V 4A M23419/1-019 FM01A125V5A FM01-125V 5A M23419/1-020 Referenced documents. In additio

20、n to MIL-PRF-23419, this document references the following: MIL-STD-202 MIL-PRF-19207/26 The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoeve

21、r for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Provided by IHSNot for ResaleNo reproduction or networking pe

22、rmitted without license from IHS-,-,-MIL-PRF-23419/1L 6 Custodians: Preparing activity: Army - CR DLA - CC Navy - EC Air Force - 85 (Project: 5920-2011-039) DLA - CC Review activities: Army; - AR, CR4, MI Navy - AS, MC, OS Air Force: - 19, 99 NSA - NS NOTE: The activities listed above were intereste

23、d in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-