DLA MIL-PRF-19978 2 E-2009 CAPACITORS FIXED PLASTIC (OR PAPER-PLASTIC) DIELECTRIC (HERMETICALLY SEALED IN CERAMIC OR GLASS CASES) STYLE CQ20.pdf
《DLA MIL-PRF-19978 2 E-2009 CAPACITORS FIXED PLASTIC (OR PAPER-PLASTIC) DIELECTRIC (HERMETICALLY SEALED IN CERAMIC OR GLASS CASES) STYLE CQ20.pdf》由会员分享,可在线阅读,更多相关《DLA MIL-PRF-19978 2 E-2009 CAPACITORS FIXED PLASTIC (OR PAPER-PLASTIC) DIELECTRIC (HERMETICALLY SEALED IN CERAMIC OR GLASS CASES) STYLE CQ20.pdf(7页珍藏版)》请在麦多课文档分享上搜索。
1、AMSC N/A FSC 5910 INCH-POUND MIL-PRF-19978/2E 15 October 2009 SUPERSEDING MIL-PRF-19978/2D 27 May 1999 PERFORMANCE SPECIFICATION SHEET CAPACITORS, FIXED, PLASTIC (OR PAPER-PLASTIC) DIELECTRIC, (HERMETICALLY SEALED IN CERAMIC OR GLASS CASES), STYLE CQ20 This specification sheet is approved for use by
2、 all Departments and Agencies of Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-PRF-19978. Inches mm Inches mm .001 0.03 .375 9.53 .004 0.10 .531 13.49 .031 0.79 .625 15.88 .032 0.81 .750 19.05 .040 1.02 1.00 25.4
3、.125 3.18 2.00 50.8 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Leads shall be solder coated solid wire, .032 (No. 20 AWG) for cases .531 and .625 in diameter, and .040 (No. 18 AWG) for cases .75 and above in diameter. Tolerance on all lead wi
4、re diameters shall be +.004, -.001. 4. Mounting hardware consisting of two lockwashers and four nuts shall be supplied with each capacitor with threaded-stud terminals. 5. These capacitors are not intended to be supported by their leads. These capacitors shall be supported with a supplementary means
5、 of mounting, such as tangential retainer or wrap-around band. The supporting device will not be supplied with the capacitor. FIGURE 1. Style CQ20 capacitors. SOLDER COATEDWIRE Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-19978/2E 2 REQUIR
6、EMENTS: Design and construction: Dimensions and configuration: See figure 1 and table I. Construction: Extended foil or laid-in-tab . Terminals: See table I. Circuit diagram: Rated voltage: See table I. Rated temperature: -65C to +125C Capacitance (Cap.) (nom): See table I. Capacitance tolerance: Se
7、e table I. Dissipation factor (DF) (max): 1.0 percent. Seal: In accordance with method 112 of MIL-STD-202, test condition letter A. Dielectric withstanding voltage (DWV): Sleeving: In accordance with MIL-PRF-19978. Barometric pressure: In accordance with MIL-PRF-19978. Test points: Circuit diagram 1
8、 - Between terminals and case. Insulation resistance (IR): Sleeving - In accordance with MIL-PRF-19978. Terminal to terminal - See table II. Vibration, low frequency: Method 201 of MIL-STD-202. Direction and duration of motion: Four hours in each of two mutually perpendicular directions (total of 8
9、hours), one parallel and the other perpendicular to the cylindrical axis. Salt atmosphere (corrosion): Not applicable. Immersion: DWV: Sleeving: In accordance with MIL-PRF-19978. IR: Sleeving: In accordance with MIL-PRF-19978. Solderability: In accordance with MIL-PRF-19978 for wire leads only. Prov
10、ided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-19978/2E 3 Terminal strength: In accordance with method 211 of MIL-STD-202. Wire leads: Test condition letter D. Threaded stud and nuts: Test condition letters A and E. Moisture resistance: DWV: Sle
11、eving: In accordance with MIL-PRF-19978. IR: Sleeving: In accordance with MIL-PRF-19978. Stability at low and high temperatures: Low temperature: Test temperature: -65C +0C, -5C. Capacitance change (max): -10 percent. High temperature: Test temperature: +125C +0C, -5C. Capacitance change (max): +10
12、percent. Life: Capacitance change (max): 5 percent. Resistance to soldering heat: In accordance with MIL-PRF-19978. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-19978/2E 4 TABLE I. Style CQ20 capacitors. Part or identifying number (PIN) 1/
13、 DC voltage Capacitance Capacitance tolerance Terminal identification Case dimensions 2/ rating (see figure 2) L .062 D .031 Volts F Inches CQ20A1KG102-1 Inches 1,000 0.0010 J, K A 1.188 .531 CQ20A1KG152-1 1,000 0.0015 J, K A 1.188 .531 CQ20A1KG222-1 1,000 0.0022 J, K A 1.188 .531 CQ20A1KG332-1 1,00
14、0 0.0033 J, K A 1.188 .531 CQ20A1KG472-1 1,000 0.0047 J, K A 1.188 .531 CQ20A1KG682-1 1,000 0.0068 J, K A 1.188 .531 CQ20A1KG103-1 1,000 0.010 J, K A 1.188 .531 CQ20A1KG153-1 1,000 0.015 J, K A 1.188 .531 CQ20A1KG223-1 1,000 0.022 J, K A 1.562 .531 CQ20-1KG333-1 1,000 0.033 J, K A,C 1.562 .625 CQ20-
15、1KG473-1 1,000 0.047 J, K A,C 1.750 .625 CQ20-1KG683-1 1,000 0.068 J, K A,C 2.000 .625 CQ20-1KG104-1 1,000 0.10 J, K A,C 2.250 .625 CQ20-1KG154-1 1,000 0.15 J, K A,C 2.250 .750 CQ20-1KG224-1 1,000 0.22 J, K A,C 2.500 .750 CQ20-1KG334-1 1,000 0.33 J, K A,C 2.750 1.031 CQ20-1KG474-1 1,000 0.47 J, K A,
16、C 3.000 1.031 CQ20-1KG684-1 1,000 0.68 J, K A,C 3.250 1.344 CQ20-1KG105-1 1,000 1.0 J, K A,C 3.750 1.344 CQ20A1KJ102-1 2,000 0.0010 J, K A 1.188 .531 CQ20A1KJ152-1 2,000 0.0015 J, K A 1.188 .531 CQ20A1KJ222-1 2,000 0.0022 J, K A 1.188 .531 CQ20A1KJ332-1 2,000 0.0033 J, K A 1.188 .531 CQ20A1KJ472-1 2
17、,000 0.0047 J, K A 1.188 .531 CQ20A1KJ682-1 2,000 0.0068 J, K A 1.188 .531 CQ20A1KJ103-1 2,000 0.010 J, K A 1.562 .531 CQ20A1KJ153-1 2,000 0.015 J, K A 1.562 .531 CQ20-1KJ223-1 2,000 0.022 J, K A,C 1.562 .625 CQ20-1KJ333-1 2,000 0.033 J, K A,C 1.750 .625 CQ20-1KJ473-1 2,000 0.047 J, K A,C 2.000 .625
18、 CQ20-1KJ683-1 2,000 0.068 J, K A,C 2.000 .750 CQ20-1KJ104-1 2,000 0.10 J, K A,C 2.250 .875 CQ20-1KJ154-1 2,000 0.15 J, K A,C 2.500 1.031 CQ20-1KJ224-1 2,000 0.22 J, K A,C 2.750 1.031 CQ20-1KJ334-1 2,000 0.33 J, K A,C 2.750 1.344 CQ20-1KJ474-1 2,000 0.47 J, K A,C 3.750 1.344 CQ20-1KJ684-1 2,000 0.68
19、 J, K A,C 3.750 1.344 CQ20A1KL102-1 3,000 0.001 J, K A 1.188 .531 CQ20A1KL152-1 3,000 0.0015 J, K A 1.188 .531 CQ20A1KL222-1 3,000 0.0022 J, K A 1.188 .531 CQ20A1KL332-1 3,000 0.0033 J, K A 1.188 .531 CQ20A1KL472-1 3,000 0.0047 J, K A 1.562 .531 CQ20A1KL682-1 3,000 0.0068 J, K A 1.562 .531 CQ20-1KL1
20、03-1 3,000 0.010 J, K A,C 1.562 .625 CQ20-1KL153-1 3,000 0.015 J, K A,C 1.750 .625 CQ20-1KL223-1 3,000 0.022 J, K A,C 2.000 .625 CQ20-1KL333-1 3,000 0.033 J, K A,C 2.000 .750 CQ20-1KL473-1 3,000 0.047 J, K A,C 2.250 .750 CQ20-1KL683-1 3,000 0.068 J, K A,C 2.500 .875 CQ20-1KL104-1 3,000 0.10 J, K A,C
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- DLAMILPRF199782E2009CAPACITORSFIXEDPLASTICORPAPERPLASTICDIELECTRICHERMETICALLYSEALEDINCERAMICORGLASSCASESSTYLECQ20PDF

链接地址:http://www.mydoc123.com/p-692554.html