DLA MIL-PRF-15733 59 B-2009 FILTERS RADIO FREQUENCY INTERFERENCE HERMETICALLY SEALED STYLE FL64.pdf

《DLA MIL-PRF-15733 59 B-2009 FILTERS RADIO FREQUENCY INTERFERENCE HERMETICALLY SEALED STYLE FL64.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-PRF-15733 59 B-2009 FILTERS RADIO FREQUENCY INTERFERENCE HERMETICALLY SEALED STYLE FL64.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、 AMSC N/A FSC 5915 MIL-PRF-15733/59B 2 June 2009 SUPERSEDING MIL-PRF-15733/59A 23 January 2004 PERFORMANCE SPECIFICATION SHEET FILTERS, RADIO FREQUENCY INTERFERENCE, HERMETICALLY SEALED, STYLE FL64 This specification sheet is approved for use by all Depart- ments and Agencies of the Department of De

2、fense. * The requirements for acquiring the filters described herein shall consist of this specification sheet and MIL-PRF-15733. * Part or Identifying Numbers (PINs) M15733/59-0001 through M15733/59-0006 are inactive for new design after 2 June 2009. For new design see table V for supersession data

3、. INCH-POUND FIGURE 1. Filter and hardware dimensions, and circuit configurations. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A B C D E F G H J Dash no. Min Max Min Max Min Max Min Max Min Max Typ Min Max Min Max 0001 - .743 (18.87) - .416 (10.5

4、7) .175 (4.45) .205 (5.21) .100 (2.54) .190 (4.83) .100 (2.54) .190 (4.83) .119 (3.02) .190 (4.83) .210 (5.330 .045 (1.14) .075 (1.91) .250-28 UNF-2A 0002 - .743 (18.87) - .416 (10.57) .175 (4.45) .205 (5.21) .100 (2.54) .190 (4.83) .100 (2.54) .190 (4.83) .119 (3.02) .190 (4.83) .210 (5.330 .045 (1

5、.14) .075 (1.91) .250-28 UNF-2A 0003 - .743 (18.87) - .416 (10.57) .175 (4.45) .205 (5.21) .100 (2.54) .190 (4.83) .100 (2.54) .190 (4.83) .119 (3.02) .190 (4.83) .210 (5.330 .045 (1.14) .075 (1.91) .250-28 UNF-2A 0004 - .743 (18.87) - .416 (10.57) .175 (4.45) .205 (5.21) .100 (2.54) .190 (4.83) .10

6、0 (2.54) .190 (4.83) .119 (3.02) .190 (4.83) .210 (5.330 .045 (1.14) .075 (1.91) .250-28 UNF-2A 0005 - .743 (18.87) - .416 (10.57) .175 (4.45) .205 (5.21) .100 (2.54) .190 (4.83) .100 (2.54) .190 (4.83) .119 (3.02) .190 (4.83) .210 (5.330 .045 (1.14) .075 (1.91) .250-28 UNF-2A 0006 - .743 (18.87) -

7、.416 (10.57) .175 (4.45) .205 (5.21) .100 (2.54) .190 (4.83) .100 (2.54) .190 (4.83) .119 (3.02) .190 (4.83) .210 (5.330 .045 (1.14) .075 (1.91) .250-28 UNF-2A 0007 - 1.170 (29.72) - .416 (10.57) .175 (4.45) .205 (5.21) .100 (2.54) .190 (4.83) .100 (2.54) .190 (4.83) .119 (3.02) .190 (4.83) .210 (5.

8、330 .045 (1.14) .075 (1.91) .250-28 UNF-2A 0008 - 1.170 (29.72) - .416 (10.57) .175 (4.45) .205 (5.21) .100 (2.54) .190 (4.83) .100 (2.54) .190 (4.83) .119 (3.02) .190 (4.83) .210 (5.330 .045 (1.14) .075 (1.91) .250-28 UNF-2A MIL-PRF-15733/59B 2 FIGURE 1. Filter and hardware dimensions, and circuit

9、configurations - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-15733/59B 3 Hex nut Lockwasher K L M N Dash no Min Max Min Max Thread Min Max 0001 .307 (7.80) .317 (8.05) .088 (2.24) .098 (2.49) .250-28 UNF-2B .395 (10.03) .410 (1

10、0.41) 0002 .307 (7.80) .317 (8.05) .088 (2.24) .098 (2.49) .250-28 UNF-2B .395 (10.03) .410 (10.41) 0003 .307 (7.80) .317 (8.05) .088 (2.24) .098 (2.49) .250-28 UNF-2B .395 (10.03) .410 (10.41) 0004 .307 (7.80) .317 (8.05) .088 (2.24) .098 (2.49) .250-28 UNF-2B .395 (10.03) .410 (10.41) 0005 .307 (7

11、.80) .317 (8.05) .088 (2.24) .098 (2.49) .250-28 UNF-2B .395 (10.03) .410 (10.41) 0006 .307 (7.80) .317 (8.05) .088 (2.24) .098 (2.49) .250-28 UNF-2B .395 (10.03) .410 (10.41) 0007 .307 (7.80) .317 (8.05) .088 (2.24) .098 (2.49) .250-28 UNF-2B .395 (10.03) .410 (10.41) 0008 .307 (7.80) .317 (8.05) .

12、088 (2.24) .098 (2.49) .250-28 UNF-2B .395 (10.03) .410 (10.41) NOTES: 1. Dimensions are in inches. 2. Metric equivalents are in parentheses. 3. Metric equivalents are given for general information only. 4. All filters shall be supplied with mounting hardware. 5. Terminal identification (nonsymmetri

13、cal filters): The case shall be marked at the threaded end of the filter with the symbol “C” or the symbol “L”, as follows: Circuit Symbol L1C 2L 6. Imperfect thread or undercut optional; .047 (1.19) max, 2 places. 7. For use in applications where mounting panel thickness does not exceed .062 inch (

14、1.57 mm). 8. Recommended mounting torque: 48 ounce-inch, maximum. FIGURE 1. Filter and hardware dimensions, and circuit configurations - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TABLE I. Electrical Characteristics. Maximum rated vol

15、tage Volts, DC AC Vrms 60 Hz or 400 Hz Minimum full load insertion loss (dB) in accordance with MIL-STD-220 over full temperature range -55C to +125C Dash no. Circuit config- uration Maximum rated current (amp) +85C to -55C +125C +85C to -55C +125C Voltage drop (volts DC) or (volts rms) max 150 kHz

16、300 kHz 1.0 MHz 10.0 MHz 1.0 GHz 0001 1/ L2 1.0 200 200 150 150 .250 12 23 44 70 70 0002 1/ L1 1.0 200 200 150 150 .250 12 23 44 70 70 0003 1/ L2 3.0 200 200 150 150 .150 7 13 29 67 70 0004 1/ L1 3.0 200 200 150 150 .150 7 13 29 67 70 0005 1/ L2 5.0 200 200 150 150 .075 7 12 24 57 70 0006 1/ L1 5.0

17、200 200 150 150 .075 7 12 24 57 70 0007 T 2.0 200 200 150 150 .200 11 19 42 70 70 0008 T 4.0 200 200 150 150 .250 10 17 32 70 70 MIL-PRF-15733/59B 1/ Inactive for new design. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-15733/59B 5 REQUI

18、REMENTS: Dimensions and configuration: As specified in figure I. Case: Metal. Case and hardware finish: In accordance with MIL-PRF-15733. Pure tin is prohibited as an undercoat and as a final finish. Seal: Glass to metal. Terminals: Solderable (see figure 1). Pure tin is prohibited as an undercoat a

19、nd as a final finish. Operating temperature range: -55C to +125C. Rated voltage: See table I. Rated current: See table I. Voltage drop: See table I. Insertion loss: See table I. Seal: In accordance with MIL-PRF-15733 and method 112, MIL-STD-202; test condition A or D. Temperature rise: In accordance

20、 with MIL-PRF-15733. Temperature rise shall be +25C, maximum. Dielectric withstanding voltage: In accordance with MIL-PRF-15733. The following exception shall apply: Test voltage: 2 times rated voltage (V dc). Barometric pressure (reduced): In accordance with MIL-PRF-15733 and method 105, MIL-STD-20

21、2; test condition D. Inrush transients test: the filters shall be subjected to test by instantaneous application of 115 V rms, 400 Hz to the filter with the output unloaded. The source impedance shall be less than 0.5 ohm and its energy capability shall not limit the inrush current to the filter. Th

22、e filters shall be subjected to this inrush a minimum of 10 times, with a maximum time of 5 minutes between applications. The input shall always be into the inductor for non-symmetrical filters. Measurements after test: Insulation resistance (at +125C) and insertion-loss shall meet initial requireme

23、nts. Transient voltage test: The filters shall be subjected to the overvoltage allowed by MIL-STD-704 for ac systems. The following details and exceptions shall apply: Preconditioning: Filter shall be energized at 115 V rms, 400 Hz carrying rated current for 15 minutes minimum. Transient application

24、: The output load shall be removed and the input voltage shall be stepped form 115 V rms to 180 volts within 20 milliseconds of removal of the load. The step from 115 to 180 volts shall be accomplished with a rise time of less than 60 milliseconds. The 180 volts shall be maintained for 100 milliseco

25、nds minimum. This cycle shall be repeated 10 times. Measurements after test: Insulation resistance (at +125C) and insertion-loss shall meet initial requirements. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-15733/59B 6 Insulation resistanc

26、e: In accordance with MIL-PRF-15733. The following details and exceptions shall apply: Test potential: Rated dc voltage. Insulation resistance: Shall not be less than 100 megohms at +25C and not less than 5 megohms at +125C, when measured between the case (ground) and all terminals connected togethe

27、r. Voltage drop: In accordance with MIL-PRF-15733. Maximum voltage drop at +25C shall be as specified in table I. Insertion loss: In accordance with MIL-PRF-15733 and table I at +25C and temperature extremes. Terminal strength: In accordance with MIL-PRF-15733 and method 211, MIL-STD-202; test condi

28、tion A (pull). Applied force: 4.5 pounds. Salt atmosphere (corrosion): In accordance with MIL-PRF-15733 and method 101, MIL-STD-202; test condition B. Shock (specified pulse): In accordance with MIL-PRF-15733 and method 213, MIL-STD-202; test condition I. Vibration, high frequency: In accordance wit

29、h MIL-PRF-15733 and method 204, MIL-STD-202; test condition D (20 G). Moisture resistance: In accordance with MIL-PRF-15733. The following exceptions shall apply: Measurements after 24-hour drying period: Dielectric withstanding voltage: Voltage at 1.8 times rated dc voltage. Insulation resistance a

30、nd insertion-loss shall meet initial requirements. Life: In accordance with MIL-PRF-15733 and method 108, MIL-STD-202. The following details and exceptions shall apply: Test condition D (1,000 hours) for qualification inspection, test condition B (250 hours) for group C inspection. Measurements afte

31、r test at +25C: Dielectric withstanding voltage at 1.8 times rated dc voltage. Insulation resistance and insertion-loss shall meet initial requirements. Voltage conditioning: Voltage conditioning shall consist of applying rated ac voltage 400 Hz to the part at +125C. The voltage shall be applied for

32、 a minimum of 250 hours. Charging and discharging current shall be limited within the range of 30 to 150 milliamperes. The test circuit shall be in accordance with figure 2. E1shall be continuously monitored and if it falls below 95 percent of ET, the test shall be stopped and the defective part rem

33、oved. Time counted toward total test time shall be the time that E1is greater than 95 percent of ET. After the completion of 250 hours and while remaining at +125C, the insulation resistance shall be measured and shall be 5 megohms minimum. Provided by IHSNot for ResaleNo reproduction or networking

34、permitted without license from IHS-,-,-MIL-PRF-15733/59B 7 FIGURE 2. Voltage conditioning test circuit. VERIFICATION Qualification inspection: Requirements of this specification sheet not currently required in MIL-PRF-15733 shall be included in qualification inspection as group VI (see table II). TA

35、BLE II. Qualification inspection. 1/ Examination or test Number of samples to be inspected Number of defectives allowed Group V Transient voltage 4 0 Inrush transients 4 * 1/ This table is an addition to table III (qualification inspection) of MIL-PRF-15733. Conformance inspection: Conformance inspe

36、ction shall be as specified in MIL-PRF-15733 except group A inspection shall be as specified in table III of this specification sheet, in the order shown. Lots that have greater than 5 percent rejects shall be considered reject lots. Reject lots may, at the option of the supplier, be resubmitted to

37、100 percent group A inspection; however, resubmitted lots which have greater than 2 percent rejects shall be rejected and may not be resubmitted for reinspection. Group C inspection shall be as specified in MIL-PRF-15733 and shall include the tests specified in table IV of this specification sheet.

38、Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-15733/59B 8 TABLE III. Group A inspection. 1/ Test or inspection Sampling procedure Thermal shock 100% Voltage conditioning 100% Dielectric withstanding voltage 100% Insulation resistance 100% V

39、oltage drop 100% Insertion loss 100% Seal Visual and mechanical inspection See MIL-PRF-15733. Group A inspection. * 1/ This table replaces table IV (Group A inspection) of MIL-PRF-15733. TABLE IV. Group C inspection. 1/ Examination or test Number of samples to be inspected Number of defectives allow

40、ed Subgroup 6 Transient voltages 4 0 Inrush transients 4 * 1/ This table is an addition to table VI (Group C inspection) of MIL-PRF-15733. Part or Identifying number (PIN): M15733/59- (dash number from table I). * Supersession data for new design: See Table V * TABLE V. Supersession data For new des

41、ign use Inactive PIN Specification sheet PIN M15733/59-0001 MIL-PRF-28861/5 M28861/05-005TB M15733/59-0002 MIL-PRF-28861/5 M28861/05-004TB M15733/59-0003 MIL-PRF-28861/5 M28861/05-008TB M15733/59-0004 MIL-PRF-28861/5 M28861/05-007TB M15733/59-0005 MIL-PRF-28861/5 M28861/05-011TB M15733/59-0006 MIL-P

42、RF-28861/5 M28861/05-010TB NOTES: * Referenced documents. In addition to MIL-PRF-15733, this specification sheet references the following documents. MIL-PRF-28861/5 MIL-STD-202 MIL-STD-220 MIL-STD-704 * Changes from previous issue: The margins of this specification sheet are marked with asterisks to

43、 indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content i

44、rrespective of the marginal notations and relationship to the last previous issue. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-15733/59B 9 Custodians: Preparing activity: Air Force - 85 DLA - CC Navy - EC DLA - CC (Project 5915-2009-009)

45、* Review activities: Air Force 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-