DLA MIL-HDBK-271-104-1985 AIRCRAFT FASTENERS INSTALLATION AND REMOVAL METHODS FOR MIL B 8831& MIL B 85667 EXPANDABLE STRAIGHT SHANK BOLTS (SLEEVEBOLTS)《(胀壳式锚杆)MIL B 8831和MIL B 8566.pdf

《DLA MIL-HDBK-271-104-1985 AIRCRAFT FASTENERS INSTALLATION AND REMOVAL METHODS FOR MIL B 8831& MIL B 85667 EXPANDABLE STRAIGHT SHANK BOLTS (SLEEVEBOLTS)《(胀壳式锚杆)MIL B 8831和MIL B 8566.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-HDBK-271-104-1985 AIRCRAFT FASTENERS INSTALLATION AND REMOVAL METHODS FOR MIL B 8831& MIL B 85667 EXPANDABLE STRAIGHT SHANK BOLTS (SLEEVEBOLTS)《(胀壳式锚杆)MIL B 8831和MIL B 8566.pdf（15页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-HDBK-271-104 15 NOVEMBER 1985 SLEEVEBOLT INSTALLATION HANDBOOK MILITARY HANDBOOK AIRCRAFT FASTENERS, INSTALLATION AND REMOVAL METHODS FOR MIL-6-8831 and MIL-6-85667 Expandable Straight Shank Bolts ( Sl eevebol ts) / Y I f 43 -0O.s :sc 530 THIS DOCUMENT CONTAINS /5 PAGES. mC M/A - 7- STATMENT A .

2、 ApDTOVed for public release, distribution s unlrrnitea. /- Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-271 -LOq 53 7797770 0006798 3 DEPARTMENT OF DEFENSE WASHINGTON 25 O.C. 20361 MIL-HDEK-271-104 I AIRCRAFT FASTENERS, INSTALLATION AND REMOVAL S

3、LEEVEBOLTS METHODS FOR MIL-8-85667 AND MIL-8-8831 1. 2. 3. 4. This standardization handbook was developed by the Department of Defense in accordance with established procedure. The publication was approved on 15 November 1985 for printing and inclusion in the military standardization handbook series

4、. This handbook provides installation and removal methods for sleevebolts. It will provide valuable information and guidance to aircraft mechanics at Navy, Army and Air Force Rework Faci 1 i ti es. This handbook is not intended to referenced in procurement specif except for infomation purposes, it s

5、upersede any specification r be cat ions nor shal quirements Every effort tias been made to include the latest information on installation and removal methods of sleevebolts. Mechanics should review this handbook periodically. Users of this handbook are encouraged to report any errors or recomnendat

6、ions to: Comnanding Officer, Naval Air Engineering Center, Code 93, SESO, Lakehurst, NJ 08733. j .- I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-HDBK-272 -JOY 53 7777770 0006979 5 = MIL-HDBK-271-104 EXPANDABLE STRAIGHT SHANK BOLT ( “SLEEVEBO

7、LT SYSTEM“ 1 SCOPE: Sleevebolts may be used in design, repair and modification. of tapered or straight shank interference fit fatigue rated fasteners. These bolts may be used in lieu FLANGE OF SLEEVE THEADOF PIN THRE ST RUCTURE -HEAD OF PIN / SLEEVE NUT -I -CAPTIVE WASHER - 1 Provided by IHSNot for

8、ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-HDBK-271 -104 53 = 7999770 0007000 b W MIL-HDBK -271 -1 04 EXPANDABLE STRAIGHT SHANK BOLT SLEEVEBOLT FASTENER INTRODUCTION: The purpose of this handbook is to cover the proper installation and removal of seeve- bolts. Thi

9、s fastening system is an assembly consisting of a headed pin and a flanged sleeve, ground externally straight for use in straight-sided clearance holes. These fasteners . are specified in MIL-8-85667 and MIL-B-8831. Interference fit in proportion to the bolt protrusion from the sleeve is realized as

10、 the bolt head underside surface comes in contact with the sleeve flange which is in contact with the structure. These bolts are used in lieu of tapered-shank fasteners (Taper-loks) when tooling or field conditions become a problem with tapered shank bolts. Provided by IHSNot for ResaleNo reproducti

11、on or networking permitted without license from IHS-,-,- MIL-HDBK-271 -104 53 9999970 0007001 W I MI L - H DBK - 2 7 1 - 1 O 4 FASTENER PART NUMER: Part number coding for Expandable-Shank Fasteners (Sleevebolt): EXAMPLE OF A PART NUMBER FOR FASTENERS SPECIFIED BY MIL-6-8831: 7 Grip length dash numbe

12、r, in sixteenths of an inch (stamp on threaded end). An X designates first oversize, Y designates second oversize. Diameter dash number in sixteenths of an inch. Basic specification sheet number. -/2 is Reduced F1 ush-Head -/3 is Protruding Head -/4 is Reduced Flush- -/5 is Protruding Head, Head, Lo

13、w Interference Low Interference EXAMPLE OF A PART NUMBER FOR FASTENERS.SPECIFIED BY HIL-8-85667: Grip length dash number, in sixteenths of an inch (stamp on threaded end). A -I designates basic diameter, X designates first oversize, i de- signates second oversize (stamp on sleeve). Oiameter dash num

14、ber in sixteenths of an inch. Basic specifiction sheet number. -/2 is Flush-Head -/3 is Protruding Head -/4 is Protruding Head -/5 is Reduced Flush- Head Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-HDBK-271 -104 53 = 7979770 O007002 T MIL -WD

15、BK-271-104 - COMPANION NUTS FOR SLEEVEBOLTS Nuts for MIL-6-85667/2 and /4 bolts shall be in accordance with MIL-N-85729. Nuts for MIL-6-85667/3 and /5 bolts shall be in accordance with MIL-N-85730. Nuts for all MIL-6-8831 bolts shall be in acordance with MIL-N-8985/3 or MIL-N-8922/1. EXPANDABLE-SHAN

16、K FASTENER GAGES: The actual bolt is used as a gage following a simple procedure. A. Check for proper fillet-radius, making sure sleeve flange is flush with structure (protruding head flush-head). 6. By drilling and checking depth with the sleevebolt, obtain the proper countersink depth (flush-head

17、type). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-HDBK-271-104 HEAD MARKING: FART NUMBER LOT TRACEABILITY 1 DENT 1 F 1 CAT I ON SYMBOL GRIP SELECTION: On flush-head type bolts, the grip is measured from the top of the sleeve flange to the en

18、d of the sleeve. On protruding head type bolts, the grip is measured from the underside of the sleeve flange to the end of the sleeve. These bolts are designed for use in stack-ups equal to but not less than .O62 inches. The extra length of the bolt in a short stack-up niay be accomnodated using a w

19、asher nut with a recessed counterbore. 7 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-HDBK-271 -1Oq 53 m 7777970 00070011 3 m MI L -HOW - 2 7 1 - 1 O 4 INSTALLATION : Step h 1: Drill straight diameter hole. . A. Select drill sites for flush

20、head bolts from Table I. B. Select drill sizes for protruding head bolts from Table II. BE Step # 2: SLEEVE. SEE TABLE 1. Insert bolt assembly into drilled hole. These illustratioiis show a protruding head (1) and a flush head (2) ready for installation. Provided by IHSNot for ResaleNo reproduction

21、or networking permitted without license from IHS-,-,-MIL-HDBK-271 -1OY 53 W 7797970 0007005 5 MIL-HOBK-271-104 Step # 3: PROTRUDING HEAD Check for adequate stack-up fille: relief. NOTE : Cutter for fillet relief of oPeration need not travel any deeper than necessary to permit full bearing of the fla

22、nge with the structures as shown. Step 13 4: FLUSH HEAD :heck far countersink iepth. NOTE : Sleevebolt is used as gage for proper coun- tersink deoth during drilling operation. tio special tooling is required for installation, a rivet gun may be used or the bolt may be tamed in until the specified n

23、ut can be placed on the threaded end. Pull the bolt in place by tightening the mated nut. Bolt driven in using standard rivet gun. STEP 4 Bolt may be seated, after driving in part way, by applying torque to nut. Final desired torque should be applied to nut to complete the iristall- ation. For final

24、 torque see Table III. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-HDBK-271 -1OL1 53 W 7777770 000700b 7 = MIL-HDBK-271-104 BOLT REMOVAL: Removal of the fastener 1s a two step process as f 01 1 ows: Step 1. After removing the coun- terbore nu

25、t the pin is knocked out using the appropriate knock-out tool “x designates bolt thread size (available through PE Fasteners). SBK-( X) BOLT REMOVAL Step 2. After removing the pin the sleeve may be knocked out using the appropriate knock-out tool SK-( x). A designates bolt diameter (al so avai 1 ab1

26、 e through P9 Fasteners). SLEEVE REMOVAL Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-HDBK-271 -104 53 9777770 0007007 9 MI L -HDBK - 2 7 1 - 1 04 TABLE I. QRILL CHART FOR FLUSH-HEAD BOLTS Decimal Radius Equivalent I .O40 I F .2570 6.70M I . O

27、40 N .3020 5/ 16“ ,3125 I ,3160 1 :Cl: . O40 I O - 8.10M 1 .3189 P .3230 Q I ,3320 U 3/8“ .3750 .O50 X ,3970 11.00M 11.20M 14409 11.40M ,4488 , O50 1 /2“ 13.20M 13.80M 14.75M .5709 - 15.50M I .6102 I . OGO - i EJOTE 1: Drills referred lo are coiiibinatiori drills with looo countersink arid have the

28、appropriate 1 isted radius. FiOTE 2: Sleevebolt: Ac,sefiibly is used as n gage For- proper- cociiiter-iiik depth during dri 11 iiig Oper-atioii. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-HDBK-271 -1Oq 53 7797770 0007008 O i D r i 1 1 Size E

29、quivalent De c i ina 1 I MIL -tiDBK .27 1 - 104 45O I Di aine ter Rad i us +.005 -. O00 t , O 1 O -.O00 Chamfer I TABLE II. WLL CHART FOR PROTRUDING HEAD BOLTS .688 I800 ,813 _-_._ .7n5 .050 .UMA , O83 . O83 8 .2380 .2570 6.70M .2638 .3020 5/ 16“ 1 .3125 .3230 0 I .3320 3/8“ ;:;: I :;:;: 1 1 .ZOM( :

30、 11.40M 13.20M : 5 19; 13. OOMf - 15.00MI .59O6 15.25M -6004 15.50M( .ti102 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-HDBK -271 -104 .7283 .7344 .7480 .7656 TABLE II. DRILL CHART FQR PROTRUDING HEAD BOLTS (Continued) .872 .a78 .892 .91 o 45

31、O Chanif er Di anie t er 11/16“ 45/64“ 18.00M 2 3 / 3 2 I 18.50M 4 7/64“ 19.00M 49/64“ 25/32“ I .7812 I .925 5 1 /64“ I .7969 I .94 1 13/16“ 2 7/ 3 2 I 55/64“ 7/8“ 22. 50tI 23. OOM 59/64“ 15/16 63/64“ - 1 1 1/64“ 1 3/64“ _- 1 1/16“ 15/61?“ 1 1,18“ 1 4/64“ 1 5/32“ 1 13/64“ 1 7/32“ 1 9/32“ - 1 19L64“

32、- 1 5/lbll 1 11/32“ 1 23/64“ 1 3/8“ 1 13/32“ 1-17/G4“ G/b4 I* 1 3/lb“ ,8125 .a438 -. 8594 .a750 .a858 .9055 .9215 .9375 .9531 .9844 1.0000 1 .O156 1.0469 1.0625 1 .O781 1,1250 1.1406 1.15b2 1. lb75 .-1,2031-. 1 .7 188 I .zn12 _- 1.2969 - - - 1 A125 1 a 31138 I. 3594 1.3750 1 . 4062 -i-: IL “19 . - _

33、 _ - - - .957 .988 1 .O03 1 .o19 1 .O30 1 .O50 1 .O66 1 .O97 1.128 1.144 1.160 1,191 -.I- 1.207 1.222 1,269 1.285 - 1.300 1 .332 1. 347 1.363 1.425 . .! :-$A !.-. 1 .(i51 1 . (IHH - . . 1.503 - -. - - - - 1 .SI9 1.578 _ 1.5911 - - - ._ _ -. -_I_ i .o82 - - - -_I Rad i us +.005 -. O00 . 083 .083 083

34、. O83 . O83 .083 . O83 . 083 . O83 .083 .083 .083 . O83 . O83 . O83 . O83 .083 .083 083 .O83 - .083 .083 .083 -_ . O83 . OH3 .083 . O83 * OH3 . OH3 _. .0r3 ,un3 . . . uti3 - -. .083 . OH3 _I_ . on3 . 083 . o97 -_-.- .097 -. .083 - Provided by IHSNot for ResaleNo reproduction or networking permitted

35、without license from IHS-,-,-tlILzHDBK -271-104 Dri 11 1 QDeciiii;l Size ,E uiva1 nt 1 7/16“ 1.4375 1 31/64 1 .4844 1 1/2“ 1.5000 TABLE II. DRILL CHART FOR PROTRUDING HEAD BOLTS (Continued) 450 C hamf e r D i ame ter Rad i us +.o10 +.O05 -.O00 -. O00 1.610 * o97 1.656 . o97 1.672 . o97 1 33/64“1 1.5

36、156 I 1.688 1 35/64“ 1.5469 1.719 1 5/8“ 1 21/32“ 1 11/16“ 1 51/64“1 . o97 . o97 1 S625 1.5781 1.6250 1.6406 1.6562 1.6875 1.7031 1.7188 1.7656 1.7812 1.7969 1.797 .I ,813 1.828 c 1.860 1.938 J 1.969 -I 1 .o97 .09L CAUTION: NOTE: to clrai- the bolt radius and obtain complete seating of the head, dri

37、ll holes with either- a 45O chaiiifcr to the size indicated, or drill holes with a radius to the size iridicated. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-HDBK-271 -LOq 53 7797770 00070LL O - MIL -HDBK -27 1 - 104 TABLE III. Installation

38、torque values for each dash number may be obtained by: 1. Read and record seating torque 2. Installation torque equals seating torque plus 10% to 15% of the seating torque. Custodians: Preparing Activity: Navy - AS Navy - AS Ait- Force - 11 Project No. 53GP-0149-08 Amy - AV 13 - I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-