DLA MIL-DTL-83723 87 E-2009 CONNECTORS ELECTRICAL (CIRCULAR ENVIRONMENT RESISTING) PLUG (THREADED COUPLING CRIMP PIN CONTACT) (SERIES III CLASSES A G K M R T W AND Z).pdf

《DLA MIL-DTL-83723 87 E-2009 CONNECTORS ELECTRICAL (CIRCULAR ENVIRONMENT RESISTING) PLUG (THREADED COUPLING CRIMP PIN CONTACT) (SERIES III CLASSES A G K M R T W AND Z).pdf》由会员分享，可在线阅读，更多相关《DLA MIL-DTL-83723 87 E-2009 CONNECTORS ELECTRICAL (CIRCULAR ENVIRONMENT RESISTING) PLUG (THREADED COUPLING CRIMP PIN CONTACT) (SERIES III CLASSES A G K M R T W AND Z).pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRICAL, (CIRCULAR, ENVIRONMENT RESISTING), PLUG, (THREADED COUPLING, CRIMP PIN CONTACT), (SERIES III, CLASSES A, G, K, M, R, T, W AND Z) This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements f

2、or acquiring the product described herein shall consist of this specification sheet and MIL-DTL-83723. FIGURE 1. Dimensions and configurations. AMSC N/A FSC 5935 INCH-POUND MIL-DTL-83723/87E 1 October 2009 SUPERSEDING MIL-C-83723/87D 30 June 1992 Provided by IHSNot for ResaleNo reproduction or netwo

3、rking permitted without license from IHS-,-,-MIL-DTL-83723/87E 2 FIGURE 1. Dimensions and configurations - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83723/87E 3 Shell size A Thread UNEF-2B B C H J K W 8 .5625-24 .290 (7.37) .

4、025 (.64) .294 (7.47) .405 (10.29) .396 (10.06) .575 (14.61) .776 (19.71) 10 .6875-24 .388 (9.86) .031 (.79) .428 (10.87) .526 (13.36) .517 (13.13) .707 (17.96) .908 (23.06) 12 .875-20 .558 (14.17) .598 (15.19) .696 (17.68) .687 (17.45) .895 (22.73) 1.080 (27.43) 14 .9375-20 .627 (15.93) .667 (16.94

5、) .765 (19.43) .756 (19.20) .957 (24.31) 1.143 (29.03) 16 1.0625-18 .772 (19.61) .794 (20.17) .892 (22.66) .883 (22.43) 1.084 (27.53) 1.268 (32.21) 18 1.1875-18 .860 (21.84) .900 (22.86) .998 (25.35) .989 (25.12) 1.209 (30.71) 1.377 (34.98) 20 1.3125-18 .985 (25.02) 1.025 (26.04) 1.123 (28.52) 1.114

6、 (28.30) 1.334 (33.88) 1.512 (38.40) 22 1.4375-18 1.110 (28.19) 1.150 (29.21) 1.248 (31.70) 1.239 (31.47) 1.459 (37.06) 1.627 (41.33) 24 1.5625-18 1.235 (31.37) 1.275 (32.39) 1.373 (34.87) 1.364 (34.65) 1.584 (40.23) 1.762 (44.75) FIGURE 1. Dimensions and configurations - Continued. Provided by IHSN

7、ot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83723/87E 4 Inches mm Inches mm Inches mm Inches mm .005 0.13 .215 5.46 .687 17.45 1.114 28.29 .007 0.18 .221 5.46 .6875 17.46 1.123 28.52 .008 0.20 .235 5.97 .696 17.68 1.150 29.21 .015 0.38 .243 6.17 .707 17.

8、96 1.180 29.97 .018 0.46 .260 6.60 .756 19.20 1.1875 30.16 .020 .51 .290 7.37 .765 19.43 1.209 30.71 .022 .56 .294 7.47 .772 19.61 1.235 31.37 .031 .79 .330 8.38 .794 20.17 1.236 31.39 .032 .81 .388 9.86 .832 21.13 1.239 31.47 .042 1.07 .396 10.05 .860 21.84 1.248 31.70 .046 1.17 .400 10.16 .875 22.

9、23 1.275 32.39 .048 1.22 .405 10.29 .883 22.43 1.334 33.88 .065 1.65 .428 10.87 .892 22.66 1.360 34.54 .068 1.73 .433 11.00 .895 22.73 1.364 34.65 .069 1.75 .479 12.17 .900 22.86 1.373 34.87 .084 2.13 .500 12.70 .9375 23.81 1.4375 36.51 .090 2.29 .510 12.95 .957 24.31 1.459 37.06 .097 2.46 .517 13.1

10、3 .959 24.36 1.5625 39.69 .101 2.57 .526 13.36 .985 25.02 1.584 40.23 .106 2.69 .558 14.71 .989 25.12 1.586 40.28 .112 2.84 .5625 14.29 .998 25.35 1.703 43.26 .125 3.18 .575 14.60 1.025 26.03 1.846 46.89 .138 3.51 .598 15.19 1.0625 26.99 .144 3.66 .627 15.93 1.084 27.53 .198 5.03 .667 16.94 1.097 27

11、.86 .204 5.18 .675 17.15 1.110 28.19 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified, tolerances are .005 (0.13 mm) for three place decimals and .01 (0.25 mm) for two place decimals and 1 for all angles. 4. The dimensions showin

12、g the relationship between the coupling ring and shell apply only when the coupling ring is in the fully forward position. 5. Rear accessory interchangeability dimensions shall be in accordance with MIL-DTL-83723. 6. Shell size 8 will not mate with MIL-DTL-26500 connectors. 7. The centerline of indi

13、cated projection must be located on vertical centerline 2. 8. See table I for contact cavities requiring this dimension. FIGURE 1. Dimensions and configurations - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83723/87E 5 REQUIREM

14、ENTS: Dimensions and configurations: See figure 1. This connector mates with MIL-DTL-83723/82 and MIL-DTL-83723/84. Insert arrangements and polarizing positions: See MIL-STD-1554 and table I. TABLE I. Insert arrangements requiring reduced diameters for raised seal barriers on contact cavities as ind

15、icated. Shell size Insert arrangements Contact cavities 8 03 1, 2, 3 10 06 1, 2, 3, 4, 5, 6 Connector accessories: See SAE-AS85049. Part or Identifying Number (PIN) example: M83723/ 87 W 22 55 N Military designation Specification sheet number Class Shell size Insert arrangement Polarizing position C

16、hanges from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue, due to the extent of the changes. Referenced documents. In addition to MIL-DTL-83723, this document references the following: MIL-STD-1554 MIL-DTL-26500 MIL-DTL-83723/

17、82 MIL-DTL-83723/84 SAE-AS85049 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83723/87E 6 CONCLUDING MATERIAL Custodians: Preparing activity: Army - CR DLA - CC Navy - AS Air Force - 85 DLA - CC Review activities: (Project 5935-2008-167) Ar

18、my - AR, MI Navy - EC Air Force - 19, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-