DLA MIL-DTL-83538 8 C-2008 CONNECTORS AND ACCESSORIES ELECTRICAL CIRCULAR UMBILICAL COVER PROTECTIVE LAUNCHER RECEPTACLE FOR MIL-STD-1760 APPLICATIONS (METRIC).pdf

《DLA MIL-DTL-83538 8 C-2008 CONNECTORS AND ACCESSORIES ELECTRICAL CIRCULAR UMBILICAL COVER PROTECTIVE LAUNCHER RECEPTACLE FOR MIL-STD-1760 APPLICATIONS (METRIC).pdf》由会员分享，可在线阅读，更多相关《DLA MIL-DTL-83538 8 C-2008 CONNECTORS AND ACCESSORIES ELECTRICAL CIRCULAR UMBILICAL COVER PROTECTIVE LAUNCHER RECEPTACLE FOR MIL-STD-1760 APPLICATIONS (METRIC).pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、 METRICMIL-DTL-83538/8C 2 June 2008 SUPERSEDING MIL-DTL-83538/8B 13 May 2005 DETAIL SPECIFICATION SHEET CONNECTORS AND ACCESSORIES, ELECTRICAL, CIRCULAR, UMBILICAL, COVER, PROTECTIVE, LAUNCHER RECEPTACLE, FOR MIL-STD-1760 APPLICATIONS (METRIC) This specification is approved for use by all Department

2、s and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-83538. FIGURE 1. Protective cover launcher receptacle. AMSC N/A FSC 5935 Provided by IHSNot for ResaleNo reproduction or networking permitted

3、 without license from IHS-,-,-MIL-DTL-83538/8C 2 FIGURE 1. Protective cover launcher receptacle - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83538/8C 3 FIGURE 1. Protective cover launcher receptacle - Continued. Provided by IH

4、SNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83538/8C 4 mm Inches mm Inches mm Inches mm Inches mm Inches 0.102 0.004 2.57 0.101 5.72 0.225 32.39 1.275 36.27 1.428 .20 0.008 2.80 0.110 6.22 0.245 32.49 1.279 36.37 1.432 .31 0.012 3.05 0.120 6.48 0.255 3

5、3.40 1.315 37.45 1.356 1.00 0.034 3.95 0.155 7.58 0.298 33.50 1.319 37.55 1.478 1.19 0.047 4.05 0.159 7.68 0.302 33.55 1.320 37.64 1.482 1.35 0.053 4.01 0.019 14.18 0.558 33.65 1.325 37.76 1.487 2.03 0.080 4.12 0.162 14.28 0.562 34.39 1.354 38.35 1.510 2.41 0.095 4.70 0.185 25.4 1.00 34.49 1.358 38.

6、46 1.514 2.50 0.098 NOTES: 1. Dimensions are in millimeters. 2. Inch equivalents are given for information only. 3. The dimension 5.72 - 4.70 indicates the location of the coupling nut when it is pushed toward the rear. FIGURE 1. Protective cover launcher receptacle - Continued. REQUIREMENTS: Dimens

7、ions and configurations: See figure 1. This protective store cover is used with MIL-DTL-83538/4. Part or Identifying Number (PIN) example: M83538/8-1. MIL-DTL-83538/12 is utilized as a tool to mate and unmate the MIL-DTL-83538/8 protective cover to the MIL-DTL-83538/4 receptacle. QUALIFICATION: Prot

8、ective covers shall be in accordance with the qualification requirements of MIL-DTL-83538. The following details and exceptions shall apply: Group A: Visual and mechanical examination (100% inspection). Group B: Not applicable. Qualification and group C: Two MIL-DTL-83538/8 protective covers and two

9、 MIL-DTL-83538/4 mating connectors shall be required for stand alone qualification. However, for group C and for a manufacturer that is in the process of qualifying MIL-DTL-83538/4 connectors concurrently with the protective cover, then one protective cover and one mating connector shall be required

10、 for testing. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83538/8C 5 Manufacturers that are qualifying this protective cover as a stand alone accessory shall conduct the following sequence of verification tests: Visual and mechanical exam

11、ination Salt spray Coupling torque Humidty Insulation resistance at ambient temperature Altitude immersion Insulation resistance at ambient temperature Dielectric withstanding voltage at sea level Temperature cycling Post test examination. Manufacturers that are in the process of qualifying MIL-DTL-

12、83538/4 receptacles concurrently with MIL-DTL-83538/8 protective covers, as well as manufacturers conducting periodic Group C, shall conduct the following sequence of tests: Visual and mechanical examination Salt spray Coupling torque Post test examination. Changes from the previous issue: Marginal

13、notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Referenced documents. In addition to MIL-DTL-83538, this document references the following: MIL-DTL-83538/4 MIL-DTL-83538/12 MIL-STD-1760 CONCLUDING MATERIAL Custodians: P

14、reparing activity: Army CR DLA CC Navy AS Air Force 85 DLA CC Review activities: Army AR, MI (Project 59352007-047) Navy EC, MC, OS Air Force 19, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change. You should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-