DLA MIL-DTL-83513 16 D-2009 CONNECTORS ELECTRICAL RECTANGULAR PLUG MICROMINIATURE POLARIZED SHELL RIGHT ANGLE PIN CONTACTS 2 ROW SOLDER TYPE STANDARD PROFILE 9 THROUGH 37 CONTACTS .pdf

《DLA MIL-DTL-83513 16 D-2009 CONNECTORS ELECTRICAL RECTANGULAR PLUG MICROMINIATURE POLARIZED SHELL RIGHT ANGLE PIN CONTACTS 2 ROW SOLDER TYPE STANDARD PROFILE 9 THROUGH 37 CONTACTS .pdf》由会员分享，可在线阅读，更多相关《DLA MIL-DTL-83513 16 D-2009 CONNECTORS ELECTRICAL RECTANGULAR PLUG MICROMINIATURE POLARIZED SHELL RIGHT ANGLE PIN CONTACTS 2 ROW SOLDER TYPE STANDARD PROFILE 9 THROUGH 37 CONTACTS .pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、 INCH-POUND MIL-DTL-83513/16D 6 March 2009 SUPERSEDING MIL-DTL-83513/16C 27 February 2003 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRICAL, RECTANGULAR, PLUG, MICROMINIATURE, POLARIZED SHELL, RIGHT ANGLE, PIN CONTACTS, 2 ROW, SOLDER TYPE, STANDARD PROFILE, 9 THROUGH 37 CONTACTS, PRINTED CIRCUIT BOA

2、RD This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-83513. Inches mm .003 0.08 .0038 0.097 .010 0.25 .015 0.38 .025 0.64 .050 1.27 .06

3、69 1.699 .096 2.44 .125 3.18 .150 3.81 .185 4.70 .190 4.83 FIGURE 1. Connector, plug, .050 inch (1.27mm) spacing.AMSC NA FSC 5935 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/16D 2FIGURE 1. Connector, plug, 050 inch (1.27 mm) spacing

4、 - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/16D 3Number of contacts A Max B +.007 (.18mm) C +.005 (.13mm) D E F Max G Max 9 1.390 (35.31) 1.150 29.21) .565 (14.35) .3338 (8.48) .1848 (4.70) .465 (11.81) .325 (8.26) 15

5、1.540 (39.12) 1.30 (33.02) .715 (18.16) .4838 (12.29) .1848 (4.70) .465 (11.81) .325 (8.26) 21 1.690 (42.93) 1.450 (36.83) .865 (21.97) .6338 (16.10) .1848 (4.70) .465 (11.81) .325 (8.26) 25 1.790 (45.47) 1.550 (39.37) .965 (24.51) .7338 (18.64) .1848 (4.70) .465 (11.81) .325 (8.26) 31 2.040 (51.82)

6、 1.800 (45.72) 1.115 (28.32) .8838 (22.45) .1848 (4.70) .465 (11.81) .325 (8.26) 37 2.340 (59.44) 2.100 (53.34) 1.265 (32.13) 1.0338 (26.26) .1848 (4.70) .465 (11.81) .325 (8.26) NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified,

7、tolerances are .005 (0.13 mm). 4. Termination organization area to be optionally molded or filled with a potting fill material capable of passing the electrical and environmental requirements of MIL-DTL-83513. Plastic molding shall conform to type GDI-30F or type SDG-F in accordance with ASTM D5948

8、or GCT-30F in accordance with ASTM D5927 or MIL-M-24519 or GST-40F in accordance with ASTM D4067 or MIL-M-24519 or GLCP-30F or GLCP-50 in accordance with ASTM D5138 or MIL-M-24519. 5. Metal shell shall be of material in accordance with MIL-DTL-83513 for class M parts. 6. Jackpost (securely attached)

9、 when specified: Corrosion resistant steel in accordance with ASTM A484/A484M and ASTM A582/A582M, 300 series stainless steel, passivated in accordance with SAE-AMS-2700, type 2. Hardware will be attached in such a fashion as to not loosen during normal de-mating conditions, where as, the mating con

10、nector hardware does not exceed the following torque values: 2.5 inch pounds for #2-56 (arrangements A G) and 4.5 inch pounds for #4-40 (arrangement H). 7. Separately molded plastic body (if used) shall conform to type GDI-30F or type SDG-F in accordance with ASTM D5948 or GCT-30F in accordance with

11、 ASTM D5927 or MIL-M-24519 or GST-40F in accordance with ASTM D4067 or MIL-M-24519 or GLCP-30F or GLCP-50 in accordance with ASTM D5138 or MIL-M-24519. 8. Wire termination pins shall conform to A-A-59551, number 24 AWG copper, except shall be tin-lead plated with a minimum of 3 percent lead. 9. Term

12、ination lengths available: .109 (2.77 mm), .140 (3.56 mm) or .172 (4.37 mm). The tolerance shall be .015 (0.381 mm) for all termination lengths. 10. Threaded insert, when specified: Corrosion resistant steel in accordance with ASTM A484/A484M and ASTM A582/A582M, 300 series stainless steel, passivat

13、ed in accordance with SAE-AMS-2700, type 2. FIGURE 1. Connector, plug, 050 inch (1.27 mm) spacing - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/16D 4NOTE: Engaging face of pin insert shown, cavity identification numbers a

14、re for reference only and do not appear on the part. FIGURE 2. Insert arrangement. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/16D 5NOTE: Engaging face of pin insert shown, cavity identification numbers are for reference only and do

15、 not appear on the part. FIGURE 2. Insert arrangement - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/16D FIGURE 3. Layout arrangement.6Provided by IHSNot for ResaleNo reproduction or networking permitted without license fr

16、om IHS-,-,-MIL-DTL-83513/16D 7FIGURE 3. Layout arrangement - Continued.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/16D 8Inches mm Inches mm Inches mm .040 1.02 .175 4.44 1.300 33.02 .050 1.27 .225 5.72 1.450 36.83 .096 2.44 .300 7.6

17、2 1.550 39.37 .100 2.54 .375 9.53 1.800 45.72 .150 3.81 1.150 29.21 2.100 53.34 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Pattern shown is for connector mounting side of PC board. FIGURE 3. Layout arrangement - Continued.Provided by IHSNot for Resal

18、eNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/16D 9REQUIREMENTS: Dimensions and configurations: See figures 1, 2 and 3. Current rating, maximum: 3 amperes per contact. Materials: Termination organization area: Potting fill material capable of passing the electri

19、cal and environmental requirements of MIL-DTL-83513. Shell: The requirements for shell materials shall be in accordance with MIL-DTL-83513. Plastic body or plastic molding: Shall conform to the requirements of GDI-30F or type SDG-F in accordance with ASTM D5948 or GCT-30F in accordance with ASTM D59

20、27 or MIL-M-24519 or GST-40F in accordance with ASTM D4067 or MIL-M-24519 or GLCP-30F or GLCP-50 in accordance with ASTM D5138 or MIL-M-24519. Jackpost: Corrosion resistant steel in accordance with ASTM A484/A484M and ASTM A582/A582M, 300 series stainless steel, passivated in accordance with SAE-AMS

21、-2700, type 2. Wire termination pins: Wire termination pins shall conform to A-A-59551, no. 24 AWG copper, except shall be tin-lead plated with a minimum of 3 percent lead. Mating connector: Shall conform to MIL-DTL-83513/2 and MIL-DTL-83513/4. Plating of termination leads: Solder dipping of termina

22、tion leads will be accomplished in SN60 PB40 or SN63 PB37 in accordance with J-STD-006. Part or Identifying Number (PIN): PIN shall consist of the letter M, the basic number of the specification sheet, a letter from the insert, a numerical code for the termination length, and a letter code for the s

23、hell finish and hardware column. M83513/16- A 01 A P Specification sheet number Insert arrangements (see figure 2) Termination length Shell finish (interface critical) Hardware A = 09 B = 15 01 = .109 02 = .140 A = Pure electrodeposited aluminum N = No hardware or threaded insert P = jackpost attach

24、 C = 21 03 = .172 C = Cadmium T = threaded insert D = 25 K = Zinc nickel W = jackpost and threaded insert E = 31 N = electroless nickel F = 37 (space applications only) P = Passivated Stainless Steel T = Nickel fluorocarbon polymer Changes from previous issue: The margins of this specification are m

25、arked with vertical lines to indicate where changes from previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based

26、 on the entire content irrespective of the marginal notations and relationship to the last previous issue. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/16D 10Referenced documents. In addition to MIL-DTL-83513, this document reference

27、s the following: MIL-DTL-83513/2 ASTM A484/A484M A-A-59551 MIL-DTL-83513/4 ASTM A582/A582M J-STD-006 MIL-M-24519 ASTM D4067 SAE-AMS-2700 ASTM D5138 ASTM D5927 ASTM D5948 CONCLUDING MATERIAL Custodians: Preparing activity: Army - CR DLA - CC Navy - EC Air Force - 85 (Project 5935-2007-064) NASA - NA

28、DLA - CC Review activities: Army - AT, MI Navy - AS, CG, MC, SH Air Force - 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-