DLA MIL-DTL-55116 D-2013 CONNECTORS MINIATURE AUDIO FIVE-PIN AND SIX-PIN GENERAL SPECIFICATION FOR.pdf
《DLA MIL-DTL-55116 D-2013 CONNECTORS MINIATURE AUDIO FIVE-PIN AND SIX-PIN GENERAL SPECIFICATION FOR.pdf》由会员分享,可在线阅读,更多相关《DLA MIL-DTL-55116 D-2013 CONNECTORS MINIATURE AUDIO FIVE-PIN AND SIX-PIN GENERAL SPECIFICATION FOR.pdf(23页珍藏版)》请在麦多课文档分享上搜索。
1、 AMSC N/A FSC 5935 MIL-DTL-55116D 07 August 2013 SUPERSEDING MIL-DTL-55116C 22 March 2004 DETAIL SPECIFICATION CONNECTORS: MINIATURE AUDIO, FIVE-PIN AND SIX-PIN GENERAL SPECIFICATION FOR This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1
2、 Scope. This specification covers waterproof, polarized, five and six contact electrical connectors (plugs and receptacles) for use in audio frequency circuits at 60 volts maximum potential and 0.5 amperes maximum current. 1.2 Designated types. The following connectors are covered by this specificat
3、ion. 1.2.1 Plug connectors. Connector plugs U-228( )/U and U-229( )/U are field serviceable and replace the unserviceable molded boot type connector plugs U-181( )/U and U-182( )/U. U-182( )/U (Rigid contacts; mates with U-228( )/U, U-183( )/U) U-228( )/U (Non-rigid contacts; mates with U-229( )/U,
4、U-182( )/U) U-229( )/U (Rigid contact; mates with U-228( )/U and U-183( )/U) 1.2.2 Receptacle connectors. U-183( )/U (Non-rigid contacts; mates with U-229( )/U) 1.3 Cable size accommodation. The cable size accommodation is identified by a dash number in accordance with table I. This number indicates
5、 the outside diameter of the cable that the connector will accommodate. TABLE I. Cable accommodation. Dash no. Cable diameter Dash no. Cable diameter -0 N/A -3 .250 .010 -1 .165 .010 -4 .290 .010 -2 .228 .010 -5 .320 .010 Comments, suggestions, or questions on this document should be addressed to DL
6、A Land and Maritime, Columbus, ATTN: VAI, Post Office Box 3990, Columbus, OH 43216-5000, or emailed to RFConnectorDLA Land and Maritime.dla.mil. Since contact information can change, you may want to verify the currency of this address information using the ASSIST Online database at https:/assist.dla
7、.mil. INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-55116D 2 1.4 Part or Identifying Number (PIN). The connector PIN will be designated in the following manner: M55116/XX-X The letter “M“ followed by the basic specification numbe
8、r. Cable size designator (0 thru 5) in accordance with table I. Specification sheet number. 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in section 3, 4, or 5 of this specification. This section does not include documents cited in other sections of this spe
9、cification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents cited in 3, 4, or 5 of this specification, whether or not they are l
10、isted. 2.2 Government documents. 2.2.1 Specifications, standards, and handbook. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contrac
11、t (see 6.2). FEDERAL SPECIFICATIONS FED-STD-H28 - Screw-Thread Standards for Federal Services L-P-410 - Plastic, Polyamide (nylon), Rigid: Rods, Tubes, Flats, Molded and Cast Parts DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-28800 - Test Equipment for use with Electrical and Electronic Equipment, G
12、eneral Specification MIL-DTL-13924 - Coating, Oxide, Black, for Ferrous Metals MIL-DTL-14072 - Finishes for Ground Signal Equipment. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-202 - Test Method Standard, Electronic and Electrical Component Parts MIL-STD-889 - Dissimilar Metals MIL-STD-13231 - Marking o
13、f Electronic Items (See supplement 1 for list of specification sheets.) (Copies of these documents are available online at https:/assist.dla.mil/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA, 19111-5094.) 2.3 Non-Government publications. The foll
14、owing documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract (see 6.2). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-
15、55116D 3 Systems for AMERICAN SOCIETY OF AUTOMOTIVE ENGINEERS (SAE) SAE AMS 5639 - Steel, Corrosion-Resistant, Bars, Wire, Forgings, Tubing, and Rings SAE AMS-QQ-N-290 - Nickel Plating (Electrodeposited) SAE AMS-QQ-S-763 - Steel, Corrosion Resistant, Bars, Wire, Shapes, and Forgings SAE AMS2700 - Pa
16、ssivation Treatment for Corrosion-Resistant Steel (Application for copies should be addressed to the American Society of Automotive Engineers, 400 Commonwealth Drive, Warrendale, PA 15096-0001, or via the internet at http:/www.sae.org.) ASTM INTERNATIONAL ASTM A313/A313M - Chromium-Nickel Stainless
17、and Heat-Resisting Steel Wire ASTM A582A852M - Free Machining Stainless and Heat-Resisting Steel Wire ASTM B16/B16M - Rod, Brass, Free-cutting, Bar and Shapes for Use in Screw Machines ASTM B194 - Copper Beryllium Alloy Plate, Sheet, Strip and Bar ASTM B196/B196M - Rod and Bar, Copper-Beryllium Allo
18、y ASTM B197/B197M - Wire, Alloy Copper-Beryllium ASTM B488 - Electrodeposited Coatings of Gold for Engineering Uses ASTM D2000 - Standard Classification System for Rubber Products in Automotive Applications ASTM D5948 - Compounds, Molding, Thermosetting ASTM D6779 - Nylon Injection and Extrusion Mat
19、erials (PA), Standard Classification (Application for copies should be addressed to the ASTM International, PO Box C700, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959, or via the internet at http:/www.astm.org.) ELECTRONIC INDUSTRIES ALLIANCE (EIA) ECA/EIA-364-31 - Humidity Test Procedure
20、for Electrical Connectors and Sockets (Application for copies should be addressed to the Electronic Industries Alliance, Technology Standards and Strategy Department, 2500 Wilson Boulevard, Arlington, VA 22201, or via the internet at http:/www.eia.org.) INTERNATIONAL ORGANIZATION FOR STANDARDIZATION
21、 (ISO) ISO 10012 - Measurement Management Systems - Requirements for Measurement Processes and Measuring Equipment 2.4 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein (except for relat
22、ed specification sheets), the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Specification sheets. The individual item requirements shall be as specified herein a
23、nd in accordance with the applicable specification sheets. In the event of any conflict between the requirements of this specification and the specification sheets, the latter shall govern. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-5511
24、6D 4 3.2 Qualification. Connectors furnished under this specification shall be products that are authorized by the qualifying activity for listing on the applicable qualified products list before contract award (see 4.5 and 6.3). 3.3 Materials. The material for each part shall be as specified herein
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- DLAMILDTL55116D2013CONNECTORSMINIATUREAUDIOFIVEPINANDSIXPINGENERALSPECIFICATIONFORPDF

链接地址:http://www.mydoc123.com/p-690976.html