DLA MIL-C-44077 B-1988 COVERALLS COMBAT VEHICLE CREWMEN-S [Use In Lieu Of DLA MIL-C-0044077 C REINST NOTICE 2]《战车队员工作服[使用 DLA MIL-C-0044077 C REINST 通知 2]》.pdf

《DLA MIL-C-44077 B-1988 COVERALLS COMBAT VEHICLE CREWMEN-S [Use In Lieu Of DLA MIL-C-0044077 C REINST NOTICE 2]《战车队员工作服[使用 DLA MIL-C-0044077 C REINST 通知 2]》.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-C-44077 B-1988 COVERALLS COMBAT VEHICLE CREWMEN-S [Use In Lieu Of DLA MIL-C-0044077 C REINST NOTICE 2]《战车队员工作服[使用 DLA MIL-C-0044077 C REINST 通知 2]》.pdf（51页珍藏版）》请在麦多课文档分享上搜索。

1、5-15- ?45? 3 November 1988 S WE RSE DING 11 December 1985 MIL-C-44077B 84 W 7977906 0378856 3 W MIL -C -4 407 7B MIL -C -4 4077A MIL ITA RY SP E CIF I CAT I ON COVERALLS, COMBAT VEHICLE CREWMEN?S This specification is approved for use by all Departments and Agencies of the Department of Defense. 1.

2、SCOPE 1.1 Scope. This document covers requirements for coveralls made of fire- resistant material. 1.2 Classification. The coveralls shall be of one type in the following sizes (see 6.2). Schedule of sizes Short Regular X-S mal 1 Small Medi um Large X-L ar ge X-Small Small Medium Large X-Large Long

3、- X-S mal 1 Small Medium Large X-L ar ge Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: U. S. Army Natick Research, Development, and Engineering Center, Natick, MA 01760-5014 by using the self-

4、 addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A FSC 8415 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. THIS DOCUMENT CONTAINS C/ PAGES. Provided by IHSNot for ResaleNo reproductio

5、n or networking permitted without license from IHS-,-,-MIL-C-44077B 4 7777706 0378857 5 MIL -C -4 407 7B 2. APPLICABLE DOCUMENTS 2.1 Government documents. * 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this specification to the

6、 extent specified herein. Unless otherwise specified, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation. SPECIFICATIONS FE DE RAL T-T-881 - V-F-106 - JJ-W- 155

7、 - DDD-L -20 - PPP-B-636 - MILITARY MIL-F-10884 - MIL-F-21840 - MIL-L-35078 - MIL -T -4 35 4 8 MIL -T -4 3 63 6 MIL-W-43685 MIL -T -44 1 O0 MIL -T -4 370 9 MIL -C -8 342 9 STAN DARDS FEDERAL FED-STD-75 1 MILITARY MILSTD-105 MIL -STD- 12 9 MIL -ST D- 1 4 7 MIL-STD-73 1 Twine, Cotton, Seine Fasteners,

8、 Slide, Interlocking Webbing, Textile, (Cotton, Elastic) Label: For Clothing, Equipage, and Tentage Boxes, Shipping, Fiberboard (General Use) Fasteners, Snap Fastener Tapes, Hook and Loop, Synthetic Loads, Unit: Preparation of Semiperishable Subsistence Items; Clothing, Personal Equipment and Equipa

9、ge; General Specification For Polyester-Covered Thread, Polyester Core, Cotton-, Rayon-, or Thread, Aramid Webbing, Tape, Textile, Aramid Fiber Tape, Textile Aramid Thread, Para-Aramid, Spun, Intermediate Modulus Cloth, Plain and Basket Weave, Aramid Stitches , Seams and S ti tchings Sampling Proced

10、ures and Tables for Inspection Marking for Shipment and Storage Palletized Unit Loads Quality of Wood Members for Containers and Pallets by Attributes 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL -C -4 4077B (Copies of specifications, standa

11、rds, and handbooks required by contractors in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting activity. ) 2.2 Other publications. The following documents form a part of this specification to the extent specified herein

12、. Unless otherwise specified, the issues of the documents which-are DOD adopted shall be those listed in the issue of the DODISS specified in the solicitation. specified, the issues of documents not listed in the DODISS shall be the issues of the nongovernment documents which are current on the date

13、 of the solici tation. Unless otherwise AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) D 3951 - Standard Practice for Commercial Packaging (Copies should be obtained from the American Society for Testing Materials, 191 6 Race Street, Philadelphia, PA 19103-1 187.) COLOR ASSOCIATION OF THE UNITED

14、STATES, INC. nd Department of Defense Standard Shades of Sewing Threads (Copies should be obtained from the Color Association of the United States, Inc., 343 Lexington Ave., New York, NY 10016-0927.) (Nongovernment standards and other publications are normally available from the organizations which

15、prepare or which distribute the documents. These documents also may be available in or through libraries or other informational services. . 2.3 Order of precedence, In the event of a conflict between the text of this specification and the references cited herein, the text of this specification shall

16、 take precedence. Nothing in this specification, however, shall supersede applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS - 3.1 Guide samples. Samples, when furnished, are solely for guidance and information to the contractor (see 6.3). Variation from t

17、he document may appear in the sample, in which case the document shall govern. * 3.2 First article, When specified in the contract or purchase order, a sample shall be subjected to first article inspection (see 4.3, 6.2, and 6.4). 3 Provided by IHSNot for ResaleNo reproduction or networking permitte

18、d without license from IHS-,-,-_ MIL-C-44077B 84 W 979990b 0378859 9 W MIL-C-4 4077B 3.3 Materials. 3.3.1 Basic material. The basic cloth for the coveralls shall be plain weave Olive Green 106 conforming to type II, class 3 of MIL-C-83429. 3.3.2 Fastener tapes. The fastener tapes shall be Green 3421

19、, 1 and 2 inch wide hook and pile tapes conforming to type I, class 2 of MIL-F-21840. 3.3.3 Elastic webbing. The elastic webbing shall be bleached or unbleached and shall conform to type I of JJ-W-155 in the following classes (with exceptions as indicated) : Class 1 - (Except that the water repellen

20、t and mildew resistant treatments are not required) sleeve and leg bottoms Class 6 - Waist tunnel 3.3.4 - Cord. The cord beading used for welts of pocket openings and the front openings shall conform to type I, size 18 of T-T-881. 3.3.5 Webbing. The webbing for the retrieval strap tab, the retrieval

21、 strap, and holster loop shall conform to type II of MIL-W-43685 with the following exceptions: a. The webbing for the retrieval strap shall be natural in color. b. The webbing for the liner snap fastenertabs may be natural in color; however, the same color (OG 106 or natural) must be used for all o

22、f the snap fastener tabs within a single garment. 3.3.6 Slide fasteners. The slide fasteners shall be brass with a black chemical finish and conform to size M of V-F-106 in the following types and styles (see operation 2 for length requirements): Type I, style 3 - Drop seat, and sleeve and leg side

23、openings Type I, style 7 - All pockets Type I, style 15 - Front opening 8 3.3.6.1 Slide fastener tapes. The material for the slide fastener tapes shall be aramid, dyed to match the basic material and shall show rigoodil fastness to laundering. The tapes shall be of sufficient lengths to comply with

24、respective slide fastener attachment operations. Color matching of the fastener tape under incandescent lamplight at 2300 f. 100K shall be exempt. 3.3.6.2 Colorfastness. The finished tape shall show fastness to light and laundering equal to or better than the standard sample. is available, the tape

25、shall show “fairri fastness to light after 20 standard fading hours, and “goodri fastness to laundering. When no standard sample 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-44077B 4 m 3979906 039BBb0 5 m MIL -C -4 407 7B *. 3.3.6.3 Slide

26、fastener thongs. The slide fastener thongs shall be 1/4-inch To prevent fraying, the wide tape, Olive Green 106 conforming to MIL-T-43709. thong tape ends shall be either seared or ultrasonically cut. 3.3.7 Thread, aramid and para-aramid. The thread shall be aramid, sizes B and E conforming to MIL-T

27、-43636. conforming to MIL-T-44100, may be used as an alternate to aramid sizes B and E. The color of the aramid and para-aramid threads shall be Olive Drab No. S-1, C.A. 66022, and shall show fastness to laundering equal to or better than the standard sample. When no standard sample is available, th

28、e thread shall show “good“ fastness to laundering. Para-aramid spun staple thread, size T-35 3.3.7.1 Polyester thread. Cotton, covered polyester core thread, conforming to ticket No. 50, 2 ply of MIL-T-43548 may be used as an alternate thread for bartacking. fastness to laundering equal to or better

29、 than the standard sample. standard sample is available, the thread shall show iigoodll fastness to laundering. The thread shall be dyed Olive Drab S-I, C.A. 66022, and shall show When no 3.3.8 Snap fasteners. The snap fasteners shall be brass, finish 2, male and female, consisting of stud and eyele

30、t size 1 or 2 with button size 1 or 2 and socket, conforming to style 2A of MIL-F-10884, except an uncapped button may be used to attach the socket. 3.3.9 Labels. Each coverall shall have an identification label, a size label, and instruction label, conforming to type VI of DDD-L-20, the label cloth

31、 shall be Medium Green, Cable No. 70034, 70130, or 70131, and the fastness to laundering requirements of DDD-L-20 shall apply. The color of 3.3.9.1 Identification label. The identification label shall conform to class 1. 3.3.9.2 Size label. The size label shall conform to class 2 and shall contain t

32、he following information for each respective size. information shall be printed in letters and numerals not less than 10-point and as follows: Descriptive X-Small - Short X-Small - Regular X-Small - Long Height: Below.67 in. Height: From 67 to 71 in. Height: Over 71 in. Chest: Below 33 in. Chest: Be

33、low 33 in. Chest: Below 33 in. Stock No. Stock No. Stock No. NATO Size: 6070/7484 NATO Size : 7080 /74 84 NATO Size: 8090f7484 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-4q077B 4 9999906 0398863 7 W Small - Short Height: Below 67 in. Che

34、st: From 33 to Stock No. NATO Size: 6070/8494 37 in. Medium - Short Height: Below 67 in. Chest: From 37 to Stock No. NATO Size: 6070/9404 41 in. Large- Short Height: Below 67 in. Chest: From 41 to Stock No. NATO Size: 6070/0414 45 in. X-Larae - Short MIL -C -4 407 7B Small - Regular Height: From 67

35、to 71 in. Chest: From 33 to Stock No. NATO Size: 7080/8494 37 in. Medium - Regular Height: From 67 to 71 in. Chest: From 37 to Stock No. NATO Size : 7080/9404 41 in. Large - Regular Height: From 67 to 71 in. Chest: From 41 to Stock No. NATO Size : 45 in. 7080 /O4 14 X-Large - Regular Small - Long He

36、ight: Over 71 in. Chest: From 33 to Stock No. NATO Size: 8090/8494 37 in. Medium - Long Height: Over 71 in. Chest: From 37 to Stock No. NATO Size : 8090/9404 41 in. Large - Long Height: Over 71 in. Chest: From 41 to Stock No. NATO Size: 8090/0414 45 in. X-Large - Lone; Height: Below 67 in. Chest: Ov

37、er 45 in. Stock No. NATO Size: 6070/1424 Height: From 67 to 71 in. Chest: Over 45 in. Stock No. NATO Size: 7080/1424 Height: Over 71 in. Chest: Over 45 in. Stock No. NATO Size: 8090/1424 3.3.9.3 Instruction label. The instruction label shall conform to class 3 and shall contain the following informa

38、tion: COVERALLS, COMBAT VEHICLE CREWMENS These coveralls are of low-flammability. No other special flame resistant treatments are required. 1. Wear as outer garment or as under-layer in cold climates. 2. Pockets are designed to accommodate operational equipment and personal effects. 3 Wear liner for

39、 added insulation. . 4. Brush snow or frost from garments before entering heated shelters. 5. Dry liner and coveralls separately when damp or wet. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-YY07B 89 9799906 03788b2 9 = MIL-C-44077B 6. Fo

40、r thorough cleaning, return to laundry unit for machine washing in accordance with established .procedures. make sure that all soap is thoroughly rinsed out. Coverall may be hand laundered; 7. WARNING: Launder with slide fasteners and hook and pile fasteners engaged. Do not press hook and pile faste

41、ners. 8. DO NOT STARCH. STARCH OR ANY OTHER TREATMENT THAT LEAVES A RESIDUE WILL DETERIORATE FLAME RESISTANCE. DO NOT REMOVE THIS LABEL 3.3.9.4 Combination identification-instruction label. The identification label (class 1) and the instruction label (class 3) may be combined into one label, When co

42、mbined, the item nomenclature shall not be repeated. The combination label shall conform to the requirements of the class 3 label. 3.4 Design. The coveralls feature a drop seat with slide fastener closure at sides and hook and pile tape at top edge, a retrieval strap (loop) located at a hook and pil

43、e closure at lower end of back yoke, and neck tab. pockets having slide fastener openings and welt pieces (two chest patch types, two front inside hanging, two thigh inside hanging, two shin inside hanging, and a left sleeve utility pocket, elastic at sleeve and leg bottoms, with slide fastener side

44、 opening, and an elastic waist tunnel). There are nine 3.5 Patterns. Standard patterns which provide an allowance of 1/2 inch for all double-lapped and double-stitched seams, and 3/8 inch for al!. other seams, unless otherwise specified, will be furnished by the Government. patterns shall not be alt

45、ered in any way and are to be used only as a guide for cutting the contractors work patterns. to the Government patterns. The Government The working patterns shall be identical * 3.5.1 Pattern parts. The component parts shall be cut from the material specified below and in accordance with the patter

46、n parts indicated. TABLE I. List of pattern parts Component Pattern nomenclature Cut parts Basic material Front Back yoke Upper back Lower back Front sleeve Back sleeve 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-HIL-C-LILI0778 89 7777906 03788

47、63 O W MIL -C -4 4 O7 7B TABLE I. List of pattern parts (contd) Component Patt ern nomencl ature Cut parts Basic material (cont d) Collar 1/ Chest pocket Front pockef; Shin pocket Ankle patch Front sleeve elbow patch Back sleeve elbow patch Knee patch Seat patch Waist tunnel Upper back facing Neck t

48、ab Thigh pocket Utility pocket Pencil pocket upper Pencil pocket lower Slide fastener cover Drop seat zipper facing Front zipper facing S 1 ee ve zipper facing Retrieval strap marker, front Retrieval strap marker, back 2 2 2 2 2 2 2 2 2 2 1 2 2 1 1 1 1 2 1 1/ Collar may be cut in one piece with seam

49、 allowances along back edge - deducted - 3.6 Construction. The construction shall conform in all respects to the requirements specified in table II and herein. Figure 1 is furnished solely for guidance and information. Should variation from the document appear in figure 1, the document shall govern. 3.6.1 Stitches, seams, and stitching. All stitches, seams, and stitching shall conform to FED-STD-751. The type of seam, stitching, and sti