DLA MIL-C-3779 E-1991 CASE ENGINEER BATTALION DRAFTING EQUIPMENT CANVAS《帐棚制图设备 工程师大部队》.pdf

《DLA MIL-C-3779 E-1991 CASE ENGINEER BATTALION DRAFTING EQUIPMENT CANVAS《帐棚制图设备 工程师大部队》.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-C-3779 E-1991 CASE ENGINEER BATTALION DRAFTING EQUIPMENT CANVAS《帐棚制图设备 工程师大部队》.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、flIC-C-3779E bb 7797706 0475363 5 - - MIL-C-3779E(ME) 22 November 1991 SUPERSEDING 21 June 1978 MIL-C-3779D(ME) MILITARY SPECIFICATION CASE, ENGINEER BATTALION, DRAFTING EQUIPMENT, CANVAS This specification is approved for use within the USA Belvoir Research, Development, and Engineering Center, Dep

2、artment of the Army, and is available for use by all Departments and Agencies of the Department of Defense, 1. SCOPE 1.1 ScoDe. This specification covers a canvas carrying case for engineer battalion drafting equipment. 2. APPLICABLE DOCUMENTS 2.1 Cavernment documents. 2.1.1 Specifications and stand

3、ards. The following specifications and standards form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, ci

4、ted in the solicitation (see 6.2). Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: USA Belvoir Research, Development, and Engineering Center, ALTN: STRBE-TSE, Fort Belvoir, VA 22060-5606 by usin

5、g the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A FSC 6675 DISTRIBUTION STATEMENT A. Approved for public release, distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without lice

6、nse from IHS-,-,-8 MIL-C-3779E bb I 99999Ob OY953b4 7 SPECIFICATIONS FEDERAL PPP-B - 601 PPP - B - 636 MILITARY - Boxes, Wood, Cleated-Plywood. - Boxes, Shipping, Fiberboard: MIL-P-116 - Preservation, Methods of, STANDARDS MILITARY MIL-STD-105 MIL - STD - 12 9 MIL-STD-130 MIL-STD-889 MIL-STD-1190 -

7、Sampling Procedures and Tables for Inspection - - - Dissimilar Metals. - Minimum Guidelines for Level C Preservation, by Attributes, Marking for Shipment and Storage. Identification Marking of US Military Property, Packing and Marking. (Unless otherwise indicated, copies of federal and military spec

8、ifications, standards, and handbooks are available from the Standardization Document Order Desk, Building 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094,) 2.1.2 Government drawings. The following Government drawings form a part of this document to the extent specified herein. Unless otherwise s

9、pecified, the issues are those in effect on the date of the solicitation. DRAWINGS ME TA13217E7420 - Case, Engineer Battalion, Drafting Equipment, Canvas. (Copies of drawings, publications, and other Government documents required by contractors in connection with specific acquisition functions shoul

10、d be obtained from the USA Belvoir Research,.Development, and Engineering Center, ATTN: STRBE-JDT, Fort Belvoir, VA 22060-5606.) 2.2 Non-Government Rubications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the document

11、s which are DoD adopted are those listed in the issue of the DODISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODISS are the issues of the documents cited in the solicitation (see 6.2). 2 Provided by IHSNot for ResaleNo reproduction or networkin

12、g permitted without license from IHS-,-,- MIL-C-3779E bb m 9999906 0495365 9 m 7 ERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) D 3953 - Strapping, Flat SCeel and Seals. p 4675 - Seiectipp and use Qf Flat Strapping Materials. (Qplication fpr copies should be addressed to the American Society for Te

13、sting and Mateyials, 1916 Race Street, Philadelphia, PA 19103.) (Non-Government standards and other publications are normally available from the organizations that prepare or distribute the documents. also may be availgble in or throuEh libraries or other informational services.) These documents 2.3

14、 Orber of precedence. In the event of a conflict between the text of this document and the references cited herein, (except for related associated detail specifications, specification sheets or MS standards), the text of this document takes precedence. Nothing in this document, however, supersedes a

15、pplicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Description. The case shall he in accordance with TA13217E7420 and as specified herein, 3.1.1 Drawings. - The drawings forming a part of this specification are end product drawings. No deviation from th

16、e prescribed dimensions or tolerances is permissible without prior approval of the contracting officer. tolerances could cumulatively result in incorrect fits, the contractor shall provide tolerances within those prescribed on the drawings to insure correct fit, ssembly, and operation of the case. A

17、ny data (e.g., shop drawings, layouts, flow sheets, processing prpcedures, etc, ) prepared by the contractor or obtained from a vendor to support fabrication and manufacture of the production item shall be made available upon request, for inspection by the contracting officer or the designated repre

18、sentative. Where 3.2 First article. When specified (see 6.2), a sample shall be subjected to first article inspection (see 6.3) in accordance with 4.3. 3.3 Material. Material shall be as shown on the applicable drawings, Materials not specified shall be selected by the contractor and shall be subjec

19、t to all. provisions of this specification. 3.3.1 Material deterioration prevention and control. The drafting equipment case shqll be fabricated from compatible materials, inherently corrosion resistant or treated to provide protection against the various forms of corrosion and deterioration that ma

20、y be encountered in any of the applicable operating and storage environments to which the drafting equipment case may be exposed. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- _ i- MIL-C-3779E bb = 999990b 04953bb O = 3.3.2 Dissimilar metals. Di

21、ssimilar metals shall not be used in intimate contact with each other unless protected against galvanic corrosion. Dissimilar metals and methods of protection are defined and detailed in MIL-STD-889. 3.3.3 Identification of materials and finishes. The contractor shall identify the specific material,

22、 material finish or treatment for use with component and subcomponent, and shall make information available upon request to the contracting officer or designated representative, 3.4 Recovered materials. For the purpose of this requirement, recovered materials are those materials which have been coll

23、ected from solid waste and reprocessed to become a source of raw materials, as distinguished from virgin raw materials. The components, pieces and parts incorporated in the cases may be newly fabricated from recovered materials to the maximum extent practicable, provided the drafting equipment case

24、produced meets all other requirements of this specification. Used, rebuilt or remanufactured components, pieces and parts shall not be incorporated in the drafting equipment case. 3.5 Seams. Seams shall be as shown on the applicable drawings. 3.6 Treatment of canvas. Canvas shall be treated as shown

25、 on applicable drawings. 3.7 Identification marking. The case shal1,be identified in accordance with MIL-STD-130. 3.8 Workmanship. Finished cases shall be clean and free from abrasion marks, permanently embedded creases and wrinkles, loopy and loose edges, dye stains, and streaks. 4. QUALITY ASSURAN

26、CE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified in the contract or-purchase order, the contractor may use

27、 his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed necessary to assur

28、e supplies and services conform to prescribed requirements. 4.1.1 Responsibility for compliance. All items must meet all requirements of sections 3 and 5. The inspection set forth in this specification shall become a part of the contractors overall inspection system or quality program. The absence o

29、f any inspection requirements in the specification shall not relieve the contractor of the responsibility of assuring that all products or supplies submitted to the Government for acceptance comply with all requirements of the contract. Sampling in quality conformance does not 4 Provided by IHSNot f

30、or ResaleNo reproduction or networking permitted without license from IHS-,-,-Li * MIL-C-3779E 66 W 9999906 0495367 2 W 1 - authorize submission of known defective material, either indicated or actual, nor does it commit the Government to acceptance of defective material. 4.1.2 Component and materia

31、l inspection. The contractor is responsible for a insuring that components and materials used are manufactured,. examined, and tested in accordance with referenced specifications, standards, and drawings, as applicable. 4.2 Classification of inspections. Inspection requirements specified herein are

32、classified as follows: a. First article inspection (see 4.3). b. Quality conformance inspection (see 4.4). c. Inspection of packaging (see 4.6). 4.3 First article inspection. 4.3.1 First article examination. The first article shall be examined as specified in 4.5.1. rej ection. Presence of one ormor

33、e defects shall be cause for 4.4 Quality conformance inspection. 4.4.1 SamplinK. Sampling for examination shall be in accordance with MIL-STD-105. and table IIa. A lot shall be accepted when zero defects are found and Sample size shall be determined by using MIL-STD-105, table I rejected when one or

34、 more defects are found. 4.4.2 Examination. Samples selected in accordance with 4.4.1 shall be a examined as specified in 4.5.1. Presence of one or more defects shall be cause for rejection. 4.5 Inspection procedure. 4.5.1 Examination. The cases shall be examined as specified herein for the followin

35、g defects : 101. 102. 103. 104. 105. 106. 107. 108. Dimensions not as shown on the drawings (see 3.1.1). Material not as shown on the drawings (see 3.3). Materials not resistant to corrosion and deterioration, or treated to be resistant to corrosion and deterioration for the applicable storage and o

36、perating environments (see 3.3.1). Dissimilar metals as defined in MIL-STD-889 are not effectively insulated from each other (see 3.3.2). Contractor does not have documentation available for identification of materials, material finishes, or treatment (see 3.3.3). Used, rebuilt or remanufactured com

37、ponents, pieces, or parts incorporated in the case (see 3.4). Seams not as specified (see 3.5). Treatment not as Specified (see 3.6). 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-109. Identification marking missing, incomplete, or illegible (see

38、 3.7). 110. Workmanship not as specified (see 3.8). o 4.6 Inspection of packaging. 4.6.1 Qualitv conformance inspection of pack. 4.6.1.1 Unit of Droduct. For the purpose of inspection, a completed pack prepared for shipment shall be considered a unit of product. 4.6.1.2 Sampling. Sampling for examin

39、ation shall be in accordance with MIL-STD-105. 4.6.1.3 Examination. Samples selected in accordance with 4.6.1.2 shall be Presence of one or more defects shall be examined for the following defects, cause for rejection. 111. Preservation not as specified for level A or C (see 5.1.1 and 112. Box closu

40、re not method V as specified (see 5.1.1). 113. Strapping not as specified (see 5.2.1 and 5.2.2). 114. Packing not as specified by the referenced document for level C (see 5.2.3). 115. Marking illegible, missing, incomplete, or incorrect (see 5.3). 5.1.2). 5. PACKAGING 5.1 Preservation. Preservation

41、shall be level A or C, as specified (see 6.2). 5.1.1 Level A. Each carrying case shall be folded and preserved in accordance with MIL-P-116, method III, using a close-fitting box conforming to PPP-B-636, W5c as the container. Box closure shall be in accordance with the appendix to the box specificat

42、ion, method V. 5.1.2 Level C. The cases shall be preserved in accordance with MIL-STD-1190. 5.2 Packing. Packing shall be level A, B, or C, as specified (see 6.2). 5.2.1 Level A. The carrying cases, preserved as specified in 5.1, shall be packed in close-fitting boxes conforming to PPP-B-601, overse

43、as type, style I or J. Strapping shall conform to ASTM D 3953 type 1 or 2, zinc-coated, size as applicable and ASTM D 4675. 5.2.2 Level B. The carrying cases shall be packed as specified in 5.2.1 for level A, except that boxes shall be domestic type and strapping may be zinc-coated. 5.2.3 Level C. T

44、he cases shall be packed in accordance with MIL-STD-1190. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-5.3 Markinq. In addition to any special marking specified in the contract or purchase order (see 6.2), marking shall be in accordance with MIL

45、-STD-129. 6. NOTES (This section contains information of a general or explanatory nature that may he helpful, but is not mandatory.) 6.1 Intended. use. The case is intended for carrying engineer battalion drafting equipment used in field reconnaissance. 6.2 Acuuisition requirements. Acquisition docu

46、ments should specify the following: a. Title, number, and date of this specification. b. Issue of DODISS to be cited in the solicitation, and if required, the specific issue of individual documents referenced (see 2.1.1 and 2.2). c. Time frame required for submission of first article, and number of

47、cases required (see 3.2). d. Level of preservation and packing required (see 5.1 and 5.2). e. Any special marking (see 5.3). 6.3 First article. When a first article inspection is required, the item(s) should be an initial production model. consist of one or more units. The contracting.officer should

48、 include specific instructions in acquisition documents regarding arrangements for examinations, approval of the first article test results and disposition of the first articles. Invitation for bids should provide that the Government reserves the right to waive the requirement for samples for first

49、article inspection to those bidders offering a product which has been previously acquired or tested by the Government, and that bidders offering such products, who wish to rely on such production or test, must furnish evidence with the bid that prior Government approval is presently appropriate for the pending contract. Bidders should not submit alternate bids unless specifically requested to do so in the solicitation. The first article should a