DLA DSCC-VID-V62 12658-2013 MICROCIRCUIT LINEAR ULTRACOMPACT PRECISION 10 0 V VOLTAGE REFERENCE MONOLITHIC SILICON.pdf

《DLA DSCC-VID-V62 12658-2013 MICROCIRCUIT LINEAR ULTRACOMPACT PRECISION 10 0 V VOLTAGE REFERENCE MONOLITHIC SILICON.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-VID-V62 12658-2013 MICROCIRCUIT LINEAR ULTRACOMPACT PRECISION 10 0 V VOLTAGE REFERENCE MONOLITHIC SILICON.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE APPROVED Prepared in accordance with ASME Y14.24 Vendor item drawing REV PAGE REV PAGE REV STATUS OF PAGES REV PAGE 1 2 3 4 5 6 7 PMIC N/A PREPARED BY Phu H. Nguyen DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil/ Original date of dra

2、wing YY MM DD CHECKED BY Phu H. Nguyen TITLE MICROCIRCUIT, LINEAR, ULTRACOMPACT, PRECISION 10.0 V VOLTAGE REFERENCE, MONOLITHIC SILICON 13-01-11 APPROVED BY Thomas M. Hess SIZE A CODE IDENT. NO. 16236 DWG NO. V62/12658 REV PAGE 1 OF 7 AMSC N/A 5962-V037-13 Provided by IHSNot for ResaleNo reproductio

3、n or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/12658 REV PAGE 2 1. SCOPE 1.1 Scope. This drawing documents the general requirements of a high performance ultracompact, precision 10.0 V voltage reference microcircuit

4、, with an operating temperature range of -55C to +125C. 1.2 Vendor Item Drawing Administrative Control Number. The manufacturers PIN is the item of identification. The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation: V62/1265

5、8 - 01 X E Drawing Device type Case outline Lead finish number (See 1.2.1) (See 1.2.2) (See 1.2.3) 1.2.1 Device type(s). Device type Generic Circuit function 01 ADR01-EP Ultracompact, precision 10.0 V voltage reference 1.2.2 Case outline(s). The case outlines are as specified herein. Outline letter

6、Number of pins JEDEC PUB 95 Package style X 10 JEDEC MO-193-AB Thin Small Outline Transistor Package 1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes as provided by the device manufacturer: Finish designator Material A Hot solder dip B Tin-lead plate C Gold plate

7、D Palladium E Gold flash palladium Z Other Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/12658 REV PAGE 3 1.3 Absolute maximum ratings. 1/ Supply voltage . 36.0 V Output s

8、hort circuit duration to GND . Indefinite Operating temperature range: . -55C to +125C Storage temperature range . -65C to 150C Junction temperature range -65C to 150C Lead temperature (Soldering, 60 sec) . 300C 1.4 Thermal characteristics. Thermal resistance Case outline JAJCUnit Case X 230 146 C/W

9、 2. APPLICABLE DOCUMENTS JEDEC SOLID STATE TECHNOLOGY ASSOCIATION (JEDEC) JEP95 Registered and Standard Outlines for Semiconductor Devices (Copies of these documents are available online at http:/www.jedec.org or from JEDEC Solid State Technology Association, 3103 North 10th Street, Suite 240S, Arli

10、ngton, VA 22201.) 3. REQUIREMENTS 3.1 Marking. Parts shall be permanently and legibly marked with the manufacturers part number as shown in 6.3 herein and as follows: A. Manufacturers name, CAGE code, or logo B. Pin 1 identifier C. ESDS identification (optional) 3.2 Unit container. The unit containe

11、r shall be marked with the manufacturers part number and with items A and C (if applicable) above. 3.3 Electrical characteristics. The maximum and recommended operating conditions and electrical performance characteristics are as specified in 1.3, 1.4, and table I herein. 3.4 Design, construction, a

12、nd physical dimension. The design, construction, and physical dimensions are as specified herein. 3.5 Diagrams. 3.5.1 Case outline. The case outline shall be as shown in 1.2.2 and figure 1. 3.5.2 Terminal connections. The terminal connections shall be as shown in figure 2. 1/ Stresses beyond those l

13、isted under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute maximum rated c

14、onditions for extended periods may affect device reliability. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/12658 REV PAGE 4 TABLE I. Electrical performance characteristic

15、s. 1/ Test Symbol Test conditions 12.0 V VIN 28.0 V TA= +25C unless otherwise noted. Limits Unit Min Typ Max Output voltage VOT grade 9.985 10.000 10.015 V Initial accuracy VOERRT grade 15 mV 0.15 % Temperature coefficient TCVOT grade, Case X, -55C TA +125C 25 ppm/C Dropout voltage VDO2 V Line regul

16、ation VO/VINVIN= 12.0 V to 28.0 V, -55C TA +125C 7 30 ppm/V Load regulation VO/ILOADILOAD= 0 mA to 10 mA, -55C TA +125C VIN= 15.0 V 40 70 ppm/mA Quiescent current IINNo load, -55C TA +125C 0.65 1 mA Voltage noise eN p-p0.1 Hz to 10.0 Hz 20 V p-p Voltage noise density eN1 kHz 510 nV/Hz Turn on settli

17、ng time tR4 s Long term stability 2/ VO1000 hours 50 ppm Output voltage hysteresis VO_HYS70 ppm Ripple rejection ratio RRR fIN= 10 kHz -75 dB Short circuit to GND ISC30 mA Temperature sensor Voltage output at TEMP pin Temperature Sensitivity VTEMP TCVTEMP550 1.96 mV mV/C 1/ Testing and other quality

18、 control techniques are used to the extent deemed necessary to assure product performance over the specified temperature range. Product may not necessarily be tested across the full temperature range and all parameters may not necessarily be tested. In the absence of specific parametric testing, pro

19、duct performance is assured by characterization and/or design. 2/ The long term stability specification is noncumulative. The drift in subsequent 1000 hour periods is significantly lower than in the first 1000 hour period. Provided by IHSNot for ResaleNo reproduction or networking permitted without

20、license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/12658 REV PAGE 5 Case X 1 35 4Db5 PLSE E1eASEEDETAIL ADETAIL A0-8cLA1SEATINGe1A2PLANE2Dimensions Symbol Millimeters Symbol Millimeters Min Max Min Max A 0.70 0.90 E 1.60 BSC A1 0.10 E1 2.80 BSC A2 1.00

21、e 0.95 BSC b 0.30 0.50 e1 1.90 BSC c 0.08 0.20 L 0.30 0.60 D 2.90 BSC NOTES: 1. All linear dimensions are in millimeters. 2. Falls within JEDEC MO-193-AB with exception of package height and thickness. FIGURE 1. Case outline. Provided by IHSNot for ResaleNo reproduction or networking permitted witho

22、ut license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/12658 REV PAGE 6 Case outline X Terminal number Terminal symbol Terminal number Terminal symbol 1 TEMP 5 TRIM 2 GND 4 VOUT3 VINFIGURE 2. Terminal connections. Provided by IHSNot for ResaleNo reproduc

23、tion or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/12658 REV PAGE 7 4. VERIFICATION 4.1 Product assurance requirements. The manufacturer is responsible for performing all inspection and test requirements as indicated

24、 in their internal documentation. Such procedures should include proper handling of electrostatic sensitive devices, classification, packaging, and labeling of moisture sensitive devices, as applicable. 5. PREPARATION FOR DELIVERY 5.1 Packaging. Preservation, packaging, labeling, and marking shall b

25、e in accordance with the manufacturers standard commercial practices for electrostatic discharge sensitive devices. 6. NOTES 6.1 ESDS. Devices are electrostatic discharge sensitive and are classified as ESDS class 1 minimum. 6.2 Configuration control. The data contained herein is based on the salien

26、t characteristics of the device manufacturers data book. The device manufacturer reserves the right to make changes without notice. This drawing will be modified as changes are provided. 6.3 Suggested source(s) of supply. Identification of the suggested source(s) of supply herein is not to be constr

27、ued as a guarantee of present or continued availability as a source of supply for the item. DLA Land and Maritime maintains an online database of all current sources of supply at http:/www.landandmaritime.dla.mil/Programs/Smcr/. Vendor item drawing administrative control number 1/ Device manufacture

28、r CAGE code Vendor part number V62/12658-01XE 24355 ADR01TUJZ-EP-R7 1/ The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation. CAGE code Source of supply 24355 Analog Devices 1 Technology Way P.O. Box 9106 Norwood, MA 02062-9106 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-